Search Documents

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, )"Why automate?" Automation, automatic control devices and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with a minimum of instruments for the purpose of merely guiding the operators. Processes were manually controlled by the operator on the basis of simple temperature, pressure, flow and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction savings in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material through- put, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins or producing a new and saleable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure, and (2) units which both measure and control a process variable. In coal processing, the first class of instruments, those which measure only, include analytical devices such as automatic ash, moisture and sulfur measuring units and the simple pressure, temperature, flow and level indicating devices mentioned previously. The second group of instruments, those which both measure and control, include a wide variety of units such as continuous weighing devices on conveyor belts and photoelectric cells which gauge the position of railroad cars on the track and insure that the cars are in the proper location for loading (see Chapter 15). The latter types of units as used in the coal industry differ from those used in other industries in one significant point. In coal processing these instruments need not be as highly sophisticated and accurate as in other industries; hence their cost is proportionately lower than in other industries. Because of the economic fact that coal sells for only a fraction of a cent per pound compared to dollars per pound for many chemical products, and

Jan 1, 1968

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By Carl Pierce

The writer of this article has not attempted to write a technical paper; on the contrary, he has tried to express in "steel-plant English," for steel men, a viewpoint drawn from his practice and experience. It is not his thought that it shall be taken as the "last word" in the making of this class of steel, or that good rimming steel cannot be made by any other practice. The paper was written to serve as the basis of a discussion from which it is hoped much benefit may be derived. The paper deals only with rimming steel made by the open-hearth process, and with the lower carbon steels, such as sheet and tin bar, rivet stock, skelp, etc., although good rimming steel as high as 40 to 50 carbon can be made by having good open slags and giving proper attention to working and tapping temperatures. Definition of Rimmed Steel Rimmed steel is sometimes called open or effervescing steel to differentiate it from killed or partly killed steel. It is steel made by a process which permits the free escape of gases from the metal in the molds. In passing up through the metal, the gases keep it in a rolling action from the walls of the mold inward. The top of the ingot rims in as the metal chills and the walls of the ingot get thicker, the center part remaining fluid until it reaches a pasty condition when it is covered with a cast-iron cap. The Charge In making up a charge for rimming steel, clean stock of a known composition must be selected, special attention being given to the analysis of the materials. The silicon in good rimming steel must be eliminated to a trace, therefore it is advisable to have a uniform amount going into the charge. Too much silicon gives a raw melting heat from which rimming steel is unlikely to result. For this reason a charge containing not to exceed 40 per cent. pig iron and 60 per cent. scrap, with no iron ore, is preferred to the Monell type of charge in which as high as 65 to 70 per cent. pig iron is used with a proportional amount of iron ore for the removal of the excess silicon and carbon. The silicon content of pig iron varies so much from day to day in the average blast-furnace practice that there is danger of getting too much of this element in the latter mixture when

Jan 1, 1926

By D. Turnbull, J. E. May

THE (110) [001] texture in silicon iron is of considerable interest both from the technological and scientific points of view. Its occurrence was reported more than 20 years ago.1-4 The texture develops by means of secondary re crystallizatjon5 and can be very strong, that is, greater than 90 pct alignment even thouh the primary re crystallization texture is weak or complex. This behavior is in contradistinction to the face-centered metals which develop their strong secondary recrystalliza-tion texture from a strong primary recrystalliza-tion texture.', The microstructural changes accompanying the (110) [001] texture formation in silicon iron are as follows: When properly prepared cold-rolled sheet (i.e., 0.015 in. thick) is annealed at about 800°C, primary recrystallization occurs and a fairly stable fine-grained primary recrystallized matrix of about 0.02-mm-diam grain size is produced. The material at this stage does not have the strong (110) [110] texture. As the temperature is raised to about 900°C, relatively large grains appear in the finegrained matrix and they grow at the expense of the smaller grains to many times the sheet thickness. In time the complete sample is consumed by these large grains. This process of the growth of relatively few grains (about one in 105 primary grains) at the expense of many grains is called secondary recrystallization. Since all the secondary grains are of essentially (110) [001.] orientation, the strong texture is developed by this secondary recrystallization process. Theories of the (110) [001] texture in polycrystal-line silicon iron have been proposed by Decker and Harker and by Dunn.Decker and Harker have shown that grains initially in the (110) [001] orientation will upon annealing after cold-rolling, re-crystallize back to the initial orientation. To account for the sharp texture in silicon iron they propose that (110) [001] grains become more highly strained than grains in other orientations and therefore recrystallize first. They are then the lowest energy grains and can consume their higher energy neighbors. Grains in orientations other than (110)

Jan 1, 1959

By Irwin Roman

THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years,1 but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1932

By William E. Ford, Edward Salisbury Dana

Examination in the Wet Way Examination by Means of the Blowpipe 479. The complete investigation of the chemical composition of a .mineral includes, first, the identification of the elements present by qualitative analysis, and, second, the determination of the relative amounts of each by quantitative analysis, from which last the formula can be calculated. Both processes carried out in full call for the equipment of a chemical laboratory. An approximate qualitative analysis, however, can, in many cases, be made quickly and simply with .few conveniences. The methods employed involve either (a) the use of acids or other reagents " in the wet way," or (b) the use

Jan 1, 1922

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By William E. Ford, Edward Salisbury Dana

A. Hexagonal Division 1. Normal Class (13) Beryl Type 2. Hemimorphic Class (14) Zincite Type 3. Pyramidal Class (15) Apatite Type 4. Pyramidal-Hemimorphic Class (16) Nephelite Type 5. Trapezohedral Class (17) B. Trigonal or Rhombohedral Division 1. Trigonal Class (18) Benitoite Type 2. Rhombohedral Class (19) Calcite Type 3. Rhombohedral-Hemimorphic Class (20) Tourmaline Type 4. Trirhombohedral Class (21) Phenacite Type 5. Trapezohedral Class (22) Quartz Type 6. Other Classes (23) 7. Other Classes (24) Mathematical Relations of the Hexagonal System 119. The HEXAGONAL SYSTEM includes all the forms which are referred to four axes, three equal horizontal axes in a common plane intersecting at angles of 60") and a fourth, vertical axis, at right angles to them. Two sections are here included, each embracing a number of distinct classes related among themselves. They are called the Hexagonal Division and the Trigonal (or Rhombohedral) Division. The symmetry of the former, about the vertical axis, belongs to the hexagonal type, that of the latter to the trigonal type. Miller (1852) referred all the forms of the hexagonal system to three equal axes parallel to the faces of the fundamental rhombohedron, and hence intersecting at equal angles, not 90". This method (further explained in Art. 169) had the disadvantage of failing to bring out the relationship between the normal hexagonal and tetragonal types, both characterized by a principal axis of symmetry, which (on the system adopted in this book) is the vertical crystallo raphic axis. It further gave different symbols to faces which are crystallographally identical. It is more natural to employ the three rhombohedra1 axes for tri- gonal forms only, as done by Groth (1905), who includes these groups in a Trigonal Syslem; but this also has some disadvantages. The indices commonly used in describing hexagonal forms are known as the Miller-Bravais indices, since the were adopted by Bravais for use with the four axes from the scheme used by Miller in the other crystal systems.

Jan 1, 1922

By G. A. Hellstrand

IN 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-New-foundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicat-ing about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereon, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods, under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere.. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1934

By Walter H. Munk

Generation of Waves by storms, and the transformation of waves in shallow water by local bottom topography are briefly reviewed. A detailed description of water motion in waves explains the nature and distribution of wave forces. A numerical example dealing with forces and moments against vertical piles summarizes the principles involved. Introduction The oil industry is moving into the open waters of the Gulf of Mexico. The design and construction of offshore drilling rigs present a number of difficult problems, among them problems involving the action of waves on fixed and floating structures. This paper deals with our present knowledge of ocean waves as it pertains to these problems, and the principles involved in computing wave forces against fixed structures. It is hoped that the more difficult case pertaining to floating structures can be discussed at a later time. None of the engincering aspects of the problem are entered upon in this paper, yet an understanding of the principles presented here should be helpful in the solution of practical problems. Waves are capable of exerting almost unbelievable forces. During a gale, waves at the harbor entrance of Amsterdam Canal in Holland lifted a 20-ton concrete block, which was resting on the bottom in 12ft of water, and deposited it on top of a pier which was 5 ft above the high water mark. At Wick Breakwater in Scotland, a mass of large stones in cement and bound together with iron rods, weighing 1350 tons, was broken loose and moved bodily! But one need not go to Holland or Scotland to find evidence of damage that waves are capable of inflicting (Fig I and 2). What is the mechanism by which waves are capable of exerting such enormous forces? To answer this, we must consider briefly the nature of wave motion. When a wind blows over a wheat field, waves appear to travel across the field, whereas the wheat itself remains rooted, slowly swinging back and forth. Similarly, in the case of water waves, the waveform travels swiftly over the water surface, whereas the water particles oscillate back and forth, but scarcely advance. The speed of the wave form is called wave velocity, the speed of the water particles is called orbital velocity. This fundamental difference between wave velocity and orbital velocity was already recognized by Leonardo da Vinci. Orbital velocity is generally much slower than wave velocity except for a breaking wave, a case which is of particular importance in the application to engineering problems. Forces exerted by the waves on obstacles

Jan 1, 1949

By Ralph L. Erickson

The discovery of a Carlin-type gold deposit at Cortez, Nevada, in 1966 can be attributed directly to the use of geochemical exploration techniques. Most mineral deposits owe their discovery to geologic concepts, geologic analysis, and luck, but at Cortez, geochemistry as an exploration tool played the clearly dominant role in discovery. Of course, the economic significance of the discovery had to be determined by exploration and development drilling. The story of the discovery began in 1959 when field work was initiated on a new project, "Geochemical Halos Utah and Nevada," by R.L. Erickson and A. P. Marranzino for the US Geological Survey. The Cortez district was selected for geochemical work because it was an area with good geologic control where we could address the problem of how to prospect in barren outcrops for concealed ore deposits in potentially favorable structures (buried thrust zones) or favorable host rocks in the subsurface. Geologic mapping of the Cortez 15-min quadrangle, just being completed by Gilluly and Masursky (1965), showed that the quadrangle contained excellent exposures of both the upper and lower plates of the Roberts Mountains thrust fault, a major structural feature of north-central Nevada. Roberts (1960) had noted that a number of mining districts were associated with windows in the thrust. In 1959, Erickson and Marranzino did some reconnaissance rock sampling and spring-water sampling in the siliceous clastic rocks of the upper plate of the thrust. Results of this reconnaissance prompted a full-scale sampling program in 1960 in the upper plate rocks on the west flank of the Cortez window. Results of the investigation showed that anomalously high concentrations of metals occur in the upper plate rocks, and further, that the distribution of metals is fault controlled and shows a pronounced zoning pattern (central copper zone; intermediate zinc, copper, and lead zone; and outer arsenic zone). The anomalies were interpreted as primary leakage halos that originated from metal occurrences in the thrust zone or in carbonate rocks below the thrust and moved upward along normal faults that cut both upper and lower plate rocks. Erickson gave a talk about these anomalies in the summer of 1961 to the local AIME Section in Reno, Nevada; two short reports were published that year-" Geochemical Anomalies in the Upper Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1961) and "Hydrogeochemical Anomalies in Four Mile Canyon Near Cortez, Nevada" (Erickson and Marranzino, 1961). These releases prompted blanket staking in the area by several small companies. In 1963, geologic and geochemical mapping were started by the USGS in the lower plate carbonate rocks of the Cortez window west of the quartz monzonite stock at Mount Tenabo and north of the old townsite of Cortez. The results of the work showed anomalously high concentrations of arsenic, antimony, and tungsten in jasperoid, fracture filling, and shear zones in Silurian and Devonian carbonate rocks. The anomalous area was about 1.6 km (I mile) long and 300 m (1000 ft) wide. A brief report, "Geochemical Anomalies in the Lower Plate of the Roberts Thrust Near Cortez, Nevada" (Erickson et al., 1964a), was published in 1964. During this same time period, 1959-1964, several exploration or mining companies were active in the general area (chiefly mapping geology and acquiring property). In 1964, American Exploration and Mining Company (Amex) concluded that the entire Cortez district was worthy of an extensive exploration effort involving drilling as well as geologic, geophysical, and geochemical studies. To carry out the program, Amex formed a joint venture group with the Bunker Hill Company, Vernon Taylor, Jr., and Webb Resources. Their early efforts were directed to the upper plate rocks and to the lower levels of the old Cortez silver mine. The group also drilled some shallow rotary assessment holes adjacent to the area of the arsenic, antimony, tungsten anomaly in lower plate carbonate rocks described in Erickson et al. (1964a). Assay results from these holes offered little or no encouragement to the joint venture group. Splits of these drill samples were made available to the USGS. In order to enhance any metal content present in these rocks and to determine the mineral residence of any metals detected, heavy-mineral concentrates of each 3-m (10-ft) sam-

Jan 1, 1985

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

By A.J. PHILLIPS, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Win. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm.. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four, binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for-examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

By E. C. Harder

CERTAIN typical characteristics of bauxites, ores of aluminum permit their classification into a number of categories, each of which has special features that enable grouping within it deposits from widely scattered bauxite fields. There may be local variations in conditions that have introduced differences of lesser importance between similar deposits in different fields, resulting perhaps from the influence of factors other than those that have produced the distinguishing features of each of the different groups, but in general the similarity between the deposits in each group is sufficiently striking to make the grouping indicated of interest. Several factors and conditions enter into the decomposition process that results in the development of bauxites and laterites and affects their character. The principal conditions favoring optimum bauxitization are: (1) pres- ence of rocks with easily soluble minerals yielding residues rich in alumina; (2) effective rock porosity, enabling easy access and free circulation of water; (3) normal to abundant rainfall alternating with dry periods; (4) vegetation, including bacteria, advantageously distributed; (5) available sources of appropriate solution and precipitation agencies; (6) a tropical or at least a warm climate; (7) low to moderate topographic relief, allowing free movement of the water table but a minimum of erosion; and (8) long quiet periods in earth history. Assuming that all of these factors are operating to a greater or less degree, it seems that the one that affects most the physical character of the resulting bauxite or laterite deposits is the chemical and mineralogical composition of the rocks that by their decay yield the bauxite deposits. This factor is used in the classification followed in this paper. In the process of weathering of ordinary silicate and carbonate rocks of the earth's crust, whether of igneous or sedimentary origin, it is the minerals of the alkalies that yield most readily to attack. The alkaline earth compounds also offer no great resistance, particularly the carbonates. Thus, among the rock-forming elements, those producing the most insoluble compounds are aluminum, iron, and silicon, together with certain ones of less importance, such as titanium, manganese, and phosphorus. In normal weathering processes such as prevail in temperate regions, the common minerals of rock decay are

Jan 1, 1952

By C. O. Fairchild

THE meaning of temperature control can be extended to cover not only the control of temperatures' but also the control of processes through a knowledge of the temperatures involved. In this sense it has a very wide interest. A list of the industries in which temperature control is used in one way or another would cover nearly the entire industrial field. This discussion will be confined to the field of high temperatures. In practically all industries involving operations at high temperatures, pyrometers are used or men are paid for their ability either to estimate temperatures or gage an operation by some physical or chemical change or condition dependent on temperatures. As progress is made in the development of instruments and of methods for measuring temperature, some of these highly skilled artisans are learning the use of a new tool. Many processes have been, in recent years, improved by means of exact measurement thus substituted for estimation, but in a great many industries the pyrometer has had practically no opportunity to demonstrate its usefulness. The perfecting of instruments must be accompanied with a dissemination of the knowledge that new instruments are available and can be economically used. The demand at present, however, is ahead of the supply, and many industries are handicapped by the want of pyrometers. One of the highest paid skilled tradesmen of the present time is the man in the steel rolling mill who knows when proper working temperatures are attained. The metallurgist in his development of steels is continually demanding closer adherence to given temperature ranges in the processes, and the pyrometer is rapidly becoming indispensable. Properties of the finished products are being correlated with working temperatures and so closely that in some cases even the pyrometer is taxed to give the required accuracy. The greatest progress has been made in those industries in which the lower temperatures are used, particularly below 500° C. In this lower range automatic control has been highly developed.

Jan 9, 1919

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By H. B. Smith, B. Egererg

In a previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature between 200" and 450" F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress — tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy. Tensile and Bend Tests Two ingots 73/4 in. wide, 11 in. long and ¾ in. thick were cast from the same pot. One ingot was cold-rolled in one direction to a strip 0.241 in. thick, which furnished the tensile test specimens; the other ingot was rolled in the same way to 0.253 in. and furnished the specimens for the bend tests. The ingots were cast as described in the previous paper and cold-rolled in six passes.

Jan 1, 1930

By Leon Eliel

TEN years ago a broad knowledge of aerial mapping, coupled with a smattering of geology, qualified one to speak on the subject of the appli-cation of aerial mapping to geology. Today, with aerial maps a common tool in the hands of expert geologists on every continent throughout the world, it would be nothing short of presumptuous for the author of this paper, who is not a geologist, to give any geological statements on his own authority. Relatively, today we are only purveyors of general geological gossip, with a definite case here and there by way of illustration. But we can present a story of the really marvellous strides that have been made in the evolution of aerial mapping, built around a skeleton of geological tidbits, from which some useful conclusions may be drawn. The average geologist goes about reading his aerial maps much as one would approach the problem of deciphering a cryptogram. To begin with, typical key expressions appear in recurring sequences and under certain conditions. If once the meaning of these isolated bits of infor-mation can be ascertained, the message begins to take meaning. In a similar fashion, the geologist works out his key from aerial maps of territory with which he has some familiarity. He learns that a certain type of thin, white line may mean a vein of quartz. He sees that a certain change in the photographic tone of vegetation on the ground reflects two kinds of soils on opposite sides of, a contact. He sees that a certain type of alignment of topographical features often means a fault. He learns that by the erosion pattern .he can frequently distinguish soft formations from harder ones. And so, bit by bit, he ties together the information of the picture with his experience on the ground until he develops a reasonably creditable capacity of interpretation. Through the complete gamut of surface conditions, ranging all the way from flat, arid, exposed desert terrain to dense jungle, or rugged mountains, the evidence from which the geologist must make his inter-pretation varies with bewildering profusion. The quality of photographs which are obtainable may range from perfect pictures in the desert to almost useless smudges in the steaming jungles. One thing he has learned with certainty-the airplane carrying its mapping camera is a superb reconnaissance tool, only awaiting his ingenuity in correlating the pictures with the ground to simplify most exploratory problems.

Jan 1, 1936