Search Documents

By Frederick Rhines

THE investigations of Wyman1 have demonstrated that copper deoxidized with several of the commonly used agents that confer immunity to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydro-gen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxy-gen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxi-dizing anneal, but beyond this the mecha-nism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subse-quently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves he reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the sub-scale may be complex compounds such, perhaps, as Si02-Cu20, which are partially reduced by hydrogen. These possibilities have been examined, and it has been con-cluded that the first three and possibly the fourth are operative collectively or indi-vidually under more or less predictable conditions.

Jan 1, 1940

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By M. G. Benz, J. F. Elliott

The austenite solidus of the iron-carbon system has been determined using a series of diffusion couples, each of which consisted of a specimen of austenite held in contact with a melt saturated with austenite. After the equilibrium distribution of carbon had been established by diffusion at a specified temperature, i.e. the austenite specimen had become austenite of the solidus conzposition, the diffusion couple was cooled, sectioned and anazlyzed for carbon. The solidus was found to be a straight line: A revised iron-carbon temperature-composition diagram is presented, COMPOSITION has a marked effect on the temperature at which austenite begins to melt and the austenite solidus of the iron-carbon system describing this effect has been the subject of many investigations.1-10 The significant results of these investigations are presented in Fig. 1. The experimental methods and purity of the materials used in them are summarized in Table I. In plotting the data in Fig. 1 no attempt has been made to convert these results to the International Temperature Scale of 1948," except for the data of Adcock,5 as this conversion would do little to reduce the uncertainty that exists as to the position and shape of the solidus. A point of major concern in evaluating these data is that the alloys studied, except those used by Adcock, were not binary alloys of iron and carbon, Table I. Also, it would appear that several of the methods did not permit equilibrium to be established through the system being studied. All that can be said for the results of these investigations is that they indicate only approximately the location of the solidus with the uncertainty as to its location at 1 pct C being approximately 100°C. The current investigation was undertaken to provide reliable data by which the austenite solidus could be established. It was hoped that information on the liquidus also could be developed at the same time, but experimental limitations prevented this as austenite segregated from the liquid on cooling. After a careful study of possible experimental methods and extensive laboratory tests, it was decided that the use of a series of austenite-liquid diffusion couples would provide the most reliable results. This paper describes the method and its results and also includes a complete iron-carbon temperature-composition diagram based on what are considered to be the best available data. EXPERTMENTAL METHOD The diffusion couple used for this investigation consisted of a small cylindrical pellet of austenite held in contact, at a specified temperature, with a melt saturated with austenite. The composition of the cylindrical austenite pellet was chosen to be approximately 0.1 wt pct C less than the estimated

Jan 1, 1962

By Frederick Laist

THE past year has witnessed no radical changes in methods for the reduction and refining of copper. The Carson litigation was finally brought to a close ant1 the copper smelter is again free to introduce charge into his reverberatory furnaces in whatever manner suits him best. This litigation naturally led to much experimentation with various methods of charging and with various types of bath. In some cases the charge was introduced more or less centrally on a relatively dry hearth and in other cases into a bath of greater or less depth. The results of these furnaces were meticulously compared with the results obtained in side-charger furnaces, and it was apparent that it made little, if any difference how a given furnace \\.as charged so long as care was taken that there was always something in the furnace for the flames to work on. So long as this requirement was complied with, consumption of fuel per ton of charge smelted and tonnage smelted per furnace day remained substantially the same regardless of the method of charging or the depth of bath employed. In some instances the center-charged deep-bath furnaces gave slightly better results than the side-charged particularly with respect to copper losses. The slags of the deep-bath furnaces are generally a little cleaner

Jan 1, 1930

By Ira B. Jorafemon

In the interesting Institute symposium of the preservation of peace by force, through mineral control, one important aspect of the question was not presented. This is the responsibility the United Nations, and particularly the United States, will incur the through limitation of the economic activities of nations that are now friendly to us, as well as of nations that are enemies or are under the control of enemies. After the war all nations, friends as well as enemies will be poor. Hunger and bankruptcy will, will like the sword of Damocles, hang over the heads of all of us on this blundering planet. When the actual fighting is over, there will be a universal attempt to squirm out from under the sword by resuming production of peacetime goods, for trade as well as immediate consumption.

Jan 1, 1944

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer's nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By L. D. HUNTOON

MY first article on Canadian Gold, published in the Canadian Mining Magazine in 1911 expressed the view that the Hollinger mine would repay all the money invested and that other mines would be developed in this area. Many published forecasts have since been made. Quoting from the Northern Miner of Oct. 29, 1931: "It will be noted in studying the chart prepared by this engineer that his forecast for 1931 at $50,000,000 was too modest, as the output for this country this year will be closer to $54,000,000."

Jan 1, 1932

By H. J. Mutz

THE International Nickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody.

Jan 1, 1953

By C. E. Cottrell, G. W. Preckshot, N. D. Delisle, D. L. Katz

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By J. L. Huitt, B. B. McGlothlin

The introduction of new fracture propping agents that are brittle but much stronger than sand created the problem of what loading strength is required for a propping agent to be effective in a given formation. It is shown that the load at which the propping agent crushes should exceed the load at which total embedment in the fracture faces is possible. Simple laboratory tests to determine loading strength of the propping agent and embedment in the fracture faces, and use of these data in selecting a propping agent for a given formation, are discussed. INTRODUCTION One of the most important factors in the design of hydraulic fracturing treatments is the selection of a propping agent that can effectively provide the fracture flow capacity needed for stimulation of a well. Sand, once generally accepted as being synonymous with propping agent in hydraulic fracturing, is now recognized as having limited effectiveness in many formations because of its low resistance to crushing. Sand particles are brittle and have relatively low strength. Because of this property, sand particles are crushed in rocks that offer high resistance to the penetration of fracture faces by the proppant particles when the fracture attempts to close under the action of the overburden load. For rocks that offer a high resistance to penetration, deform able particles are more effective propping agents than sand. However, for this same type of rock, a propping agent that does not deform, yet does not crush, is often more effective. Thus, a rigid propping agent with sufficient strength to prevent crushing is desirable. A method for determining the strength required for a rigid propping agent to function effectively in given formations is discussed. BEHAVIOR OF RIGID PROPPANTS AND FRACTURE FACES RELATED STUDIES An early qualitative description of the reaction of propping sand in fractures was given by Hassebroek et al.' In discussing fracturing in deep wells, the authors mentioned that even though propping sand entered the fractures, a high flow capacity did not result due to crushing or embedding of the propping sand. Dehlinger et al.2 in discussing the reaction of propping sand surmised that, because of the hardness of sand particles, deformation occurred in the fracture faces contacting the propping sand. In later studies,3,4 methods of determining the embedment of propping sand in fracture faces of soft rock and the critical load at which propping sand is crushed by the fracture faces in hard rock were discussed. In working with de-formable proppants, Kern et al. considered proppant particles to be deformed into cylindrical disks by action of the overburden and then pressed slightly into the fracture faces by further action of the overburden. Rixie et al.'0 reported on embedment pressure and presented a method of selecting a propping agent for use in given formations. The propping agents included sand, walnut shells and aluminum pellets. All these studies have contributed materially to a better understanding of propping agent behavior; however, the strength of brittle proppants (sand, glass and ceramics) required to result in embedment rather than crushing has not been discussed. This topic will be covered in the ensuing discussion. PROPPANT PARTICLE CRUSHING—-EMBEDMENT For this discussion, a rigid propping agent is considered to be one that is brittle and fails under tensile stress when loaded to a critical value. In an earlier study4 it was shown that the Hertzian4 loading theory could be applied to a spherical brittle propping agent if the propping agent and fracture faces behaved elastically. At the failure of the proppant, the ratio of the load to the square of the diameter of the particle should be constant for a given material combination, or: Lc/dp2=C ............(1) A partial derivation of this equation from proppant and formation properties is included in the Appendix. Should a rigid particle not be crushed as a load is applied, it embeds in the fracture faces. A study3 of particle embedment in fracture surfaces has been published. The embedment can be described by an equation based on Meyer's metal penetration hardness relationships: d1/dp=B 1/2[L/dp2]m/2..........(2) In Eq. 2, B and m are constants that are characteristic of the rock; the significance of the other terms is shown in Fig. 1. A STANDARD DEFINITION FOR PROPPANT LOADING STRENGTH Eq. 1 is useful in appraising propping agent strength," but it is strictly applicable only when the area of contact between a particle and a fracture face (or loading plate)

Jan 1, 1967

By Frederic E. Carter

There have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

By G. W. Preckshot, C. E. Cottrell, D. L. Katz, N. D. Delisle

Most crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir. mechanisms. Asphalt has been the subject of widespread investigation but, owing to the complexity of the substances being considered, progress has been slow. Investigators working primarily with the asphaltic substances have treated the subject from the colloidal standpoint and have developed theories that picture the asphaltic particles as surrounded by adsorbed materia1s.14,15,17,24 The deasphaltization of lubricating oil by the use of solvents treats the subject primarily from the standpoint of liquid-liquid equilibria.'' A complete understanding of asphaltic substances would make possible the following of the material from its initial state in the crude oil through precipitation processes to the final plastic stage, the most common form of which is used in asphaltic pavements. Since these asphaltic particles are very small, it appears 'hat the electron microscope4 might be a useful tool in studying the precipitation processes. Specimens are examined by the electron microscope in a vacuum and as very thin films, requiring special techniques in preparation of samples. A brief description of the electron microscope and its operation will bring out the difficulties and advantages of its use for this problem. The first work was done with crude oils that had been diluted with solvents for the preparation of the film to be examined. Later a technique was developed by which the undiluted oil film could be made thin enough for direct examination. These two techniques show vastly different results Asphaltic particles have been precipitated from crude oils by a variety of

Jan 1, 1943

By J. W. Bolton, S. A. Weigand

This paper discusses some fundamental metallurgical principles involved in production of sound cast bronze. In a previous paper the writers advanced the theory that "oxidation" in bronze castings is due to incipient shrinkage, and showed the effect of reducing melting atmospheres.' In the present paper the effects of certain impurities and of actual oxidizing conditions are shown. The appendix deals with the appearance of various inclusions. For many years the prevailing opinion has been that unsoundness, dark colored fractures and other phenomena accompanying porosity and weakness in bronzes are due to oxidation. The actual troubles are caused by fissures of intercrystalline type, which are often mistaken for intercrystalline films. These weaken the metal and make it porous. Grave doubt regarding the accuracy of the oxidation theory appears when several research papers presented within the last 10 years are reviewed critically. In 1919, Comstock2 conducted metallographic researches, attempting to identify "oxides" in synthetically prepared metals. He found that oxides of tin, aluminum, zinc, etc. are different from the intercrystalline films (or cavities) to which porosity is due. Apparently he believed that these "oxide films" may be caused by volatile oxides of zinc or of phosphorus or by dissolved gases thrown out of solution during solidification of the metal. In 1923, Woyski and Boeck3 definitely questioned the accuracy of the oxidation theory and indicated the danger from reducing atmospheres. They say that "oxidation, gassing and shrinkage may produce effects very similar." In 1926, investigations by Iwasé4 showed marked change in absorp-tion coefficients for various gases in copper above and below the liquidus.

Jan 1, 1930

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957

By R. W. Raymond

CLARENCE King born January 6,1842, at Newport, R. I. His ancestors on both sides mere New Englanders, of English blood, and among them not a few distinguished themselves in art, science, politics or commerce. His grandfather, Samuel Vernon King (partner in 1803 in the house of Talbot, O1yphant & King, later known as King $ Co.), was a pioneer in the China trade, and four of his sons succeeded him in the business. Three of the four died in the far East; and one of

Jan 1, 1903

By Leon Dominian

I. INTRODUCTION APART from local needs in the country's development, the interest attached to Turkish fuels grows chiefly out of the importance of the railway industry in Asiatic Turkey. Geographical conditions make of the tracks in this region the most essential link in a chain of world-girdling lines. By its position Asia Minor can be likened to a bridge in the through routes destined to connect European factories with Asiatic and African markets. An uninterrupted right-of-way from points in central Europe to populous Indian cities must necessarily pass through the valleys A Anatolia. Crossing thence the Taurus Mountains its natural passage is indicated as the Mesopotamian lowland and the shores of the Indian Ocean. Similarly land connection between Europe and Africa can be obtained only by passage through Asia Minor, Syria and Palestine. The occurrence of fuel within an area of such significance from the

Jan 6, 1916

By J. L. Dumanoir, Maurice Martin

The induction-electrical log is a combination of a SP curve, a short normal curve, and an induction log; all three logs being recorded simultaneously in a single run. The spacing of the short normal is 16 in. The induction log is designated as 5FF40, which means that the sonde involves five coils and a focusing system, and that the distance between the main coils is 40 in. Examples of induction-electrical logs are shown in Figs. 13 and 15. The right-hand track contains the induction conductivity curve. The scale of this curve is linear with the units of conductivity, i.e., mhos/m or millimhos/m (mmhos/m), increasing from right to left. The same curve can be read in the reverse direction as a resistivity log, with a hyperbolic scale. In the middle track, the solid curve represents the short normal. (An amplified short normal is also shown in Fig. 15). The dotted curve is the resistivity curve of the induction log, i.e., the reciprocal of the conductivity curve, recorded with the same linear scale as the short normal. The SP is in the left-hand track. In this combination, the SP curve and the 16-in. normal are the essential correlation curves, as in the conventional electrical log. The induction log provides a more accurate and detailed record of formation boundaries than the conventional log, especially in hard rock territories. Furthermore, the induction-electrical log makes possible the determination of fluid content, particularly in thin beds—at least qualitatively and very often quantitatively. In such thin beds, because of the adverse effect of the adjacent formations, the responses of the conventional devices are generally doubtful and/or incom-plete. Another advantage of the new combination is that the induction log is little affected by the presence of thin hard streaks interbedded within the permeable sections, whereas such occurrences are the cause of serious distortions of the long normal and lateral curves. The evaluation of saturation from any resistivity log implies the knowledge of the true resistivity R, of the bed and of the resistivity R.. of the flushed zone, or at least of the ratio Rxo/Rc. With the induction-electrical log run in fresh mud, the 16-in. nor-mal has a smaller radius of investigation than the induction log, so that the former reads closer to R.. and the latter closer to Rt. Thus, it has been observed that the ratio of the 16-in. normal to the induction log readings can be used as a basis for the interpretation in terms of saturation, with the help of appropriate charts. The purpose of the present paper is essentially to explain this procedure and to provide the corresponding charts. On the other hand, when a formation is deeply invaded, the response of any log (in particular the induction log) depends upon the radial distribution of formation resistivities behind the wall of the hole, which itself is a function of the arrangement of the fluids saturating the formation pore spaces. This paper, accordingly, will begin with a schematic description of the distribution of fluids and resistivities in the invaded zone. Next, some essential characteristics of the induction log will be reviewed. Finally, the determination of the interpretation charts and their application will be explained. The discussion will be confined to the case of fresh muds, i.e., muds whose resistivity is at least five times as great as that of the formation waters. With the present equipment the induction log is not well adapted for logging in salty mud. The Laterolog and guard electrode log are at their best under conditions of low resistivity mud. Accordingly, when these tools were introduced a few years ago, the use of salty mud was recommended. Now, with the introduction of induction logging, spe-

Jan 1, 1958

By R. G. Hawthorne

This report is concerned with fluid displacement in porous media, in those cases where viscous and gravitational forces control the displacement. Such a system would usually be found in a sand body of large physical dimensions such as an oil reservoir, although it is possible to create such a system in the laboratory. It is shown that the position of the fluid interface can be predicted by numerical calculations using a basic idea presented by Dietz. Fluid flow is considered in a vertical plane in a homogeneous, porous medium of sufficient thickness that the capillary transition zone is small in comparison with the total reservoir. A theory developed by Dietz' is used to make numerical calculations of the position of the fluid interface. The results for several conditions are compared with scaled model experiments. The results show that, for gas drive in a reservoir of steep dip, a relatively low flow rate can displace large volumes of oil before gas breakthrough. On the other hand, water injection at favorable mobility ratio and low dip may show best performance at high rates. Water tends to underride the oil and, given sufficient rime, will break through without much oil displacement. For certain conditions, which include relatively low flow rate, the interface is a straight line and its behavior is simple to calculate. At higher flow rates, the interface is unstable, and a numerical solution was programed for an automatic computer. In general, good agreement is shown between the fluid model and the computed results so long as gravitational forces have control. For a water drive at very unfavorable mobility ratio, many small water fingers appear. These viscous fingers are not controlled by the relatively small gravitational forces. When viscous fingering becomes the controlling factor, the mathematical model is oversimplified, and results do not check the fluid flow model. INTRODUCTION Present methods of reservoir analysis depend upon certain simplifying assumptions to obtain mathematical descriptions of practical use. Material-balance methods (Muskat2 or Tarner2) assume uniform fluid saturations in the entire reservoir, or in a few subdivisions of the reservoir. An unsteady-state flow calculation by West, er at considered pressure and saturation changes in flow to a well during solution gas drive, and neglected gravity effects. Results showed only a 4 per cent difference for ultimate oil recovery by the Muskat method, even though the case chosen for study was one in which unsteady-state effects should be high. The Buckley-Leverett5 method commonly assumes a one-dimensional flow system. It is applicable at high flow rates where viscous forces predominate over gravity forces. Simultaneous, parallel flow of the two fluids is assumed, and the concept of a fluid interface is not introduced. Permeabilities to each fluid for a given saturation must be known. The method is not applicable for a two-dimensional system where cross flow becomes possible. Less well known is the displacement equation derived by Dietz. This method is designed for two-dimensional flow systems and assumes a definable fluid interface within the porous medium. Dietz showed that, for a range of low flow rates, the interface would be stable. straight and at an angle of inclination which could be simply calculated. At a certain critical flow rate, the calculated interface tilt would equal the formation dip. For higher flow rates, a finger of displacing fluid would invade the displaced fluid. Dietz indicated that his method applied only to macroscopic reservoir behavior, while the Buckley-Leverett method applied to the small transition zone at the fluid interface. The examples worked out in this report are based on the fluid-displacement theory of Dietz. It is shown that the Dietz theory may be used to derive equations analogous to the Buckley-Leverett equations. In contrast to the Buckley-Leverett method, flow is considered in a plane rather than being limited to a line. Rather than a frontal advance, the movement of a fluid interface is followed. For flow rates substantially exceeding the critical rate and for high viscosity ratio, many fingers of invading fluid occur-—rather than the single finger assumed by Dietz. On the other hand, so long as some gravitational influence remains, the flow is not entirely parallel to the bedding planes as assumed by Buckley and Leverett; therefore, both methods fail to give an adequate descrip-

By Hugh Rose

THE properties of the company lie within the Pachuca district, State of Hidalgo, Mexico, connected by three railway lines with Mexico City, 55 miles southwest, and by two lines with Vera Cruz, 250 miles southeast. The ores were formerly divided by sorting into two classes, smelting and milling, the former averaging about 2 oz. gold and 335 oz. silver, the latter 0.12 oz. gold and 23 oz. silver. The smelting ores were sold to custom plants, principally the American Smelting & Refining. Co. at Aguascalientes. The milling ores were treated by the patio process at the Guadalupe Hacienda, at Pachuca. This patio was probably the largest in existence at the time and continued in active operation up to March, 1910. In January, 1910, the mines and patio were sold to English interests, represented by Camp Bird Limited. Two new companies were formed, the Compañia de Santa Gertrudis, S. A., to operate the mines, and the Compañia Beneficiadora de Pachuca, S. A., to build and operate a custom cyanide milling plant. (Fig. 1.) GEOLOGY The historical geology of the Pachuca district is described by Fred J. Pope as follows: 1. The most recent sedimentary rocks in the district belong to the Cretaceous period. 2. The Cretaceous rocks were penetrated by large intrusions of ande-site (referred to hereafter as primary andesite) which occur as elliptical dome-shaped masses, striking northwest-southeast. These andesite bodies are from 8 to 15 miles long and from 6 to 10 miles wide. 3. A period of erosion during which the contour of the andesite domes was changed. 4. Andesite flows (secondary andesite) which rest unconformably on the primary andesites.

Jan 8, 1916

By C. D. Stahl, S. M. Farouq Ali

This investigation attempts to describe and simulate the alcohol displacement process by means of a cell model, as employed in chemical engineering practice. The proposed model is more simple than previously proposed models. and utilizes parameters chosen on a theoretical basis. The model successfully reproduced the formation of the stabilized bank and the breakthrough of alcohol, the latter depending on one of the model parameters, which may be correlated with the length of the porous medium. Moreover, the effects of the phase behavior of the liquid system involved, as observed in experimental studies, were reproduced. Several variations of the basic model were devised and tested on a digital computer. These included the cases in which: (1) the actual value of fractional flow was used in cell-to-cell computations; (2) the number of cells was varied within the same run; and (3) incomplete rather than complete phase equilibrium was assumed within each cell. The proposed cell model clarifies the basic mechanism of the process. Detailed concentration profiles obtained for each cell, for instance, showed the mechanism of bank formation in relation to the phase behavior characteristics. The results obtained indicated a varying degree of phase equilibrium concommitant with changes in the velocities of the phases in an actual alcohol displacement. This condition was approximated by changing the number of cells during the simulation. Interesting information was obtained on the influence of path length on the efficiency of alcohol displacement, which has been the subject of some controversy. Certain limitations preclude the use of the proposed model as a substitute for experimental studies. The results obtained were, nevertheless, of value in interpreting the experimental results. INTRODUCTION During recent years considerable effort has been directed toward an understanding of alcohol displacement, the process whereby oil and water are recovered from a porous medium by the continuous injection of a solvent. The complex nature of the physical process involved has so far defied a complete mathematical treatment. Other methods of approach, amounting to an overall material balance, have been proposed, yielding useful information on certain aspects of the process.1-3 Taber et al, in particular, defined the displacement mechanism in terms of the phase behavior of the alcohol-oil-brine system invoIved.2 Wachmann reported a mathematical treatment of alcohol displacement subject to certain simplifying assumptions? Donohue proposed the use of a "cell model" for simulating alcohol disPlacement.5 The nature of the assumptions involved limited the utility of the model. The present work attempts to examine the variables involved in the simulation of alcohol displacement and discusses several possible versions of the basic cell model. Under certain conditions the model results are similar to the experimental results. In particular, the spontaneous formation of of the stabilized bank and the effects of the system phase behavior were successfully reproduced. PREVIOUS WORK ON CELL MODELS Cell models and the theoretical plate concept are often used in solving chemical engineering problems in which an explicit mathematical solution may be difficult or impossible to obtain. Examples of such applications occur in distillation, gas-liquid chroma tography,6 reactor technology, absorption, etc. In petroleum engineering, such a model was used by Attra7 to describe non-equilibrium gas drive, and by Higgins and Leigh ton8 to calculate sweep efficiency in water flooding. Aris and Amundsen pointed out the equivalence between the diffusion model and perfectly mixed cells connected in series.9 Deans proposed a three-parameter cell model to simulate two-component

Jan 1, 1966