Search Documents

By Frederick Mark Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and sciences. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By E. C. Carris

THE particular field of application of machines utilizing air currents as the primary separating medium is in the cleaning of the fine sizes of bituminous coal. Approximately 12,000,000 tons of bituminous coal were cleaned by air machines during 1940.They have not found any application for cleaning anthracite. Since the development and introduction of the first successful commercial pneumatic oscillating machine for cleaning bituminous coal in 1916, by the Sutton, Steele and Steele Co., Dallas, Texas, and the American Coal Cleaning Corporation, formerly of Welch, W. Va., four other successful pneumatic coal-cleaning machines have been developed and introduced to the American coal-mining industry: 1. Peale Davis: "Pneumo-Gravity" machine, 1924. 2. Arms "Concentrator," oscillating table, 1924. 3. Hey1 and Patterson oscillating table, 1927. 4. "Stump Air-Flow," pulsating air jig, 1932. Out of these five developments only the Sutton, Steele and Steele, or American Oscillating, and the Stump Air-Flow Jig remain on the market. They are the predominating pneumatic coal-cleaning machines in use in the United States. HISTORY OF AMERICAX TYPE SEPARATOR The first successful American machine, the CJ table (Fig. 1) was developed by the Sutton, Steele and Steele Co. The SJ table was the first standard model designed specifically for the cleaning of coal. It was installed in the original Crane Creek plant, owned and operated by the American Coal Co. at McComas, West Virginia. This plant was designed by The Roberts and Schaefer Co., Chicago, Ill., working in cooperation with the American Coal Cleaning Corporation, which had taken over the patent rights and sale of the pneumatic separators. Eight machines were installed in this plant. They were known as the type SJ. They were 60 by 84 in., the short dimension being the width of

Jan 1, 1943

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By Walter von der Linden

A description is presented of the mining conditions of four longwall shield type support installations in the Pittsburgh seam in northern West Virginia and southwestern Pennsylvania. Details of roof control and operating procedures, production and performance data, and equipment description and basic engineering specifications are given for these four longwall installations. The range of mining heights was between 150 and 250 cm (60 and 95 in.). The major accomplishment of the shield supports in all four faces was the provision of an almost 100% availability for coal cutting; i.e., the face-down time due to roof control problems and support maintenance requirements was minimal.

Jan 1, 1978

By B. H. G. Brady, C. M. St. John

Computational schemes for analysis of rock mass response to excavation, loading and other imposed changes, are employed pervasively in rock mechanics practice. Applications range in complexity from determination of stress and displacement distributions around openings, to prediction of the thermo-hydromechanical behaviour of a saturated fissured mass. While this may be taken as apparent sophistication in rock mechanics design activity, the indiscriminate use of computer methods may sometimes conceal inferior and inadequate engineering procedures. These inadequacies may not always be recognized, due to the general uncertainties which are inherent in rock mechanics investigations. This paper seeks to identify some common deficiencies in rock mechanics applications of computational schemes, and to propose ways of eliminating them. It also indicates some specific developments and applications of computational procedures, which are required to address persistent design problems in geomechanics practice.

Jan 1, 1982

By E. P. Pfleider, W. D. Lacabanne

Rotary percussive drilling, vibro-drilling, vibro-rotation drilling, rotary pulsating drilling-all names that mean the same thing-are gradually appearing in mining literature. What is rotary percussive drilling? It is a combined system superimposing a rapid percussive impact on a continuous rotary action in an attempt to utilize the most desirable features of both methods. At present single and multiple carriage-mounted rotary percussion units are being used in the European coal mining regions. One well engineered unit is the Hausherr "Albo" rotary percussive drill, utilizing two alternately operating percussion pistons, and another is the multiple-unit, jumbo-mounted Salzgitter machine. Niisse & Grafer also manufacture rotary percussion drills.

Sep 1, 1955

By Granville S. Borden

This brief is a reconnaissance report on some prospects in the field of taxation which can safeguard our Mineral Resources. The brief is a prospectus soliciting help and enthusiastic cooperation in the common task of developing these prospects in a manner which will be most beneficial to all parties-the owners, operators, employees, tradesmen, the federal and state governments, and the people of this nation.

Jan 4, 1950

By R. P. King

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.' They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan'gin' using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role ad the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By S. J. McCarroll

THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.1 During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO, process was constructed. Numerous operation difficulties ensued, and the plant was closed when the manganese situation in the country eased.

Jan 3, 1954

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

Discussion of the paper of John H. Hall, presented at the New York. Meeting, October, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1247 to 1256. WILLIAM 'R. WEBSTER, Philadelphia, Pa.:-I would like to call ,attention to the fact that the results of the ordinary tension and bend tests do not always give us the information we want even if we figure out the amount of work done. You want a bending test of sufficient width and full thickness. In the case of eyebars, for instance, I have had experience with a 10- by 1-in. eyebar which gave perfectly good results in a full-size test of the finished bar. The 10- by 1.5-in. and 10- by 1.75-in. eyebars from the same heats-of steel were absolutely worthless in full-size tests. The narrow bending tests from all these bars gave good results. Bat after going into the matter fully, we found that if pieces about 3 in. wide and full thickness were used for the. cold bending tests, the heavier material would not stand this test, but failed. That is, in order to check the quality of the rolled bar you should have a wide piece of full thickness for cold bending, as the narrow pieces give misleading results. J. E. JOHNSON, JR., New York, N. Y. :-I would like to ask if there have been any tests made to compare the results of Charpy tests with the true dynamic test similar .to the Wohler test, except that the piece is subjected to a tensile or compressive stress and to alternating stresses in addition, at the same time. This seems to me to approach more nearly than any other test to the conditions of actual service. where the piece is under a fixed initial stress plus a highly variable and often alternating stress. Some tests were made on this plan in England within a year or two. The test piece was Subjected to either a tensile or compressive stress of known amount and simultaneously to alternating stresses in addition. Such a. test as this gives information which we cannot get by a tensile test or even from the tensile strength multiplied by an. elongation. Such tests, however, are exceedingly tedious and require long periods of time in order to obtain valuable results. If material could be subjected to these dynamic tests and the same material to the. Charpy shock test, and if some reasonable qualitative relation could be established between the results of the two tests, then we could assume that the shock test, which is so simple and easy to make, was a measurably accurate test of the dynamic qualities of the material. At present it does not seem

Jan 12, 1913

By Danforth R. Hale, R. E. Blair

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the US over the past decade as a man-made mineral and a multimillion dollar crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for "cultured quartz"-that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to US government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezoelectric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can be varied through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1983

By Edmund S. Davenport

The production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium. Materials and Methods The thorium employed in this investigation was made from pure thorium oxide (ThO2) by the Ca-CaCl2 reduction. The washed and dried metal powder was pressed into bars approximately 0.160 in. dia. and 10 in. long, at a pressure of 75,000 Ib. per sq. in. The bars were heat-treated in vacuum at 1175' C. for 1 hr. This treatment yielded ingots sufficiently dense and coherent for mechanical working. Thorium has been successfully worked without a protective metallic covering, but for the purposes of this investigation it was more convenient to inclose the ingots in soft iron tubes and swage or roll cold to the desired sizes. The iron sheath was dissolved with nitric acid, leaving the cold-worked thorium exposed. Chemical Analyses Analyses of typical samples of the material used in this work arc given in Table 1. Thorium powder oxidizes in moist air, even at room temperature; no unusual precautions were taken to prevent such oxidation of the material used in this investigation. A certain amount of oxidation probably takes place during pressing; certainly during heat-treating unless a very slow heating schedule is employed. These factors account

Jan 1, 1930

By Nathaniel Arbiter, Chas. H. Behre

Two outstanding factors characterize most undertakings in the mineral industries: (1) mineral deposits are not equally distributed over the earth but are localized by natural processes, and (2) the mineral industries are largely based upon wasting assets. Neither of these factors is invariably true, for a few mineral materials, such as water, are essentially world-wide and others are replaced periodically by processes not unlike crop production. Indeed, with some, such as the salts in the sea, the supply is cyclic in short or long periods, whereas others, like water, though locally or periodically in short supply, are essentially inexhaustible. But to the extent that most minerals are limited to certain areas and are "permanently" consumed, any industry founded upon them, by implication, demands great care in planning for the most effective extraction-the essence of wise and conservative expenditure. Several less unusual yet also truly fundamental factors in the economics of the mineral industry are those involving (1) the various kinds and properties of mineral materials, which influence their use; (2) their geologic and geographic availability; and (3) the 'techniques unique to their discovery, exploration, and utilization. This chapter is designed primarily as a brief background for later ones and as a summary of the several unusual or at least special factors and of their effect upon the economics of the mineral industry. The social and political and especially the economic aspects of the industry are the main subjects of this volume and are dealt with in extended fashion in subsequent chapters. Fundamental Characteristics of Mineral Deposits DEFINITIONS Minerals are naturally occurring compounds of nonliving matter, each technically defined as having ( 1 ) a chemical composition that may vary

Jan 1, 1964

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By W. H. Bassett, C. Davis

Although brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent, copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,' the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By L. D. Jaffe, D. C. Buffum, F. L. Carr

SINCE the temper brittleness of steels is generally considered to be a grain-boundary phenomenon¹,² it would be expected that austenitic grain size would affect temper brittleness. Several investigators"" reported that temper brittleness, as measured by room-temperature impact tests, increased as the austenitiz-ing temperature was raised. It was subsequently pointed out that conclusions as to temper brittleness based upon room-temperature impact tests are likely to be misleading.1,6 Hurlich7 used a range of testing

Jan 1, 1954