Search Documents

By James B. Fletcher

Leaching of the block caved mine from 1941 through 1970 is described, and the improvements made are listed. Detailed is the increased knowledge of leaching gained through this operation, including methods used in forecasting production, prediction of the economical end point, rate of recovery, and ultimate recovery.

Jan 1, 1972

By L. W. Saperstein, W. W. Kaufman

Stimulated by the hearing protection clauses in the 1969 Coal Mine Health and Safety Law, attempts were made to determine what safety hazards, in terms of warning signal discrimination, are attendant upon the wearing of hearing protectors. Warning signals of dangerous roof conditions were collected and analyzed from 11 different coal mines in four different coal seams. Primarily, signals of audible level emanating from roof, floor, or coal were recorded. The interpretations of these signals were seen to be very dependent upon coincident visual and tactile signals. Acoustic character of such signals is shown to be dependent upon the spectral energy distribution of the pulses. Roof talk signals generally have broad-band spectra concentrated below 5 kHz. Reverberation times of acoustic pulses are generally less than 0.5 sec in duration. Indications have developed which link the coal mine entry dimensions with the nature of noises recorded there. Related experiments suggest that roof talk can be discriminated from background noise equally well when wearing protection as when not. This conclusion is only appropriate when noise levels warrant the wearing of protection. When quiet, the wearing of protection somewhat reduces discriminatory ability.

Jan 1, 1976

By J. Weertman

High-temperature creep experiments were carried out on indium, lead, and on binary substitutional alloys of In-Pb, In-Sn, In-TI, In-Cd, In-Hg, Pb-Bi, Pb-Sn, Pb-In, and Pb-Cd. The stress at which the power law creep equution breaks down was found to be much smaller for indium and lead than for metals with larger elastic moduli. The exponent over the stress in the power law creep equation was found to decrease upon alloying from values close to 4.5 to values near 3. THIS paper describes a set of high-temperature creep experiments made on high-purity lead and indium and on lead-rich and indium-rich single-phase binary alloys of various metals. These ex- periments were carried out to check two predictions of some creep equations derived by us"2 from a dislocation creep model due essentially to Mott. This model is shown in Fig. 1. Here dislocation loops are emitted from sources, not shown, situated on different slip planes. As the loops expand they come into each others' stress fields and are stopped. However, at high temperatures, as Mott has pointed out.

Jan 1, 1961

By Leroy Palmer

ALL the domestic. production of magnesite during 1925 came from two states, California and Washington. Of a total of 120,660 tons of crude ore, 64,600 tons, or 54 per cent., were produced in California.1 Of .this quantity California produced about 99 per cent. of the caustic calcined, but only 10 per cent. of the dead-burned. The largest producer was C. S. Maltby, of San Francisco, who operated the Red Mountain mine, in Santa Clara County, and the Sampson mine, in San Benito County, under lease. These two mines have been studied by the author, and offer interesting comparisons as to mining and treatment methods and final products. GEOLOGY The general geology of the magnesite deposits of California has been described by Hess,2 Bain3 and others,4 and although a detailed discussion is not necessary here, a brief summary will assist in understanding mining conditions. California magnesite, when comparatively pure, is usually a white, fine-grained rock, with a conchoidal fracture, occurring in veins and lense-like masses in serpentine. The veins vary considerably in width, and usually occur in a series of more or less parallel veins intersected by other series or systems of veins, probably following original or secondary fissures in the enclosing serpentine. The most generally accepted theory of origin is that the magnesite was formed by the action of surface waters charged with C02 percolating downward through fissures and changing the magnesium silicates of the serpentine into magnesium carbonate.

Jan 1, 1927

By Walter Mueller

Transition in the underground coal industry, begun with the passage of the Federal Coal Mine Health and Safety Act of 1969, should be completed midway in the 1972-80 period. Surprisingly, many of the far reaching effects of this act have been, for the most part, beneficial to the industry from the standpoint of health, safety and basic operating standards. Production has dwindled, but the next few years will see production declines level out. Average declines of approximately 27% have been recorded since passage of the 1969 act, with costs increasing an average of $1.50 per ton throughout the industry. Nationwide averages presently are in the range of 14 tons per man-shift, and by 1980 this may be further reduced to a 10-ton per man-shift average for the industry. But in spite of the many temporary set-backs affecting the industry, the marketing opportunities are clearly visible. Due primarily to the energy squeeze facing the U.S. over the near term, the 'underground coal operator is and will be enjoying unusual leverage in selling his product.

Jan 10, 1972

By Herbert D. Drechsler

Mining Finance is the interrelated aspects of "determining the total amount of funds to employ in a mining firm; allocating these funds efficiently to various assets; and, obtaining the best mix of financing in relation to the overall valuation of the firm." The first section is an overview of the financing problem through examination and discussion of the Balance Sheet and Income Statement. The next section is a discussion of the nature of the criteria developed in feasibility study. The third section describes type of capital funds, and the final section describes case studies of mining finance

Jan 1, 1985

By William E. Ford, Edward Salisbury Dana

1. Normal Class (6) Zircon Type 2. Hemimorphic Class (7) Iodusuccinimide Type 3. Pyramidal Class (8) Scheelite Type 4. Pyramidal- Hemimorphic Class (9) Wulfenite Type 5. Sphenoidal Class (10) Chalcopyrite Type 6. Trapezohedral Class (11) Nickel Sulphate Type 7. Tetartohedral Class (12) Mathematical Relations to the Tetragonal System THE TETRAGONAL SYSTEM includes all the forms which are referred to three axes at right angles to each other of which the two horizontal axes are equal to each other in length and interchangeable and the third, the vertical axis, is either shorter or longer. The horizontal axes are designated by the letter a; the vertical axis by c (see Fig. 166). The length of the vertical axis expresses properly the axial ratio of a : c, a being uniformly taken as equal to unity. The axes are orientated and their opposite ends designated by plus and minus signs exactly as in the case of the Isometric System. Seven classes are embraced in this system. Of these the normal class is common and important among minerals; two others have several representatives, and another a single one only. It may be noted that in four of the classes the vertical axis is an axis of tetragonal symmetry; in the remaining three it is an axis of binary symmetry only.

Jan 1, 1922

By Wm. Terry Siemers, Frank E. Kottlowski, George S. Austin

The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded $227 million. The state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fuorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand. Non-metallic resources are distributed throughout the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9% to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1982

By Price E. R.

The coal industry was beset with work stoppages and strikes throughout the year, and there was some loss in markets to oil and gas. These conditions, along with the mild decline in industrial activity, the steel strike, and the reduction in exports, contributed to an unfavorable year for the industry. All coal mines are working three days a week at the time of writing, and in estimating production for the year, it will be assumed that the mines will continue to work on that basis through December. Total production of bituminous coal in 1949 is estimated at 420 million tons, which is 179,518,229 tons under the production in 1948. Anthracite production is expected to reach 39,400,000 tons as compared with 57,139,948 tolls in 1948, a loss of 17,739,948 tons. Coal stocks, as of January 1, 1949, were 69,373,000 tons but at the end of the year will have dropped to approximately 22 million tons. Regardless of the difficulties during the current year, the industry has made substantial

Jan 1, 1950

By O. W. Ellis

IN VIEW of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal in the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metallic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone are used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt.

Jan 1, 1930

By Y. Oinouye, H. Ries

Of the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which result in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.' There appears to be a difference of opinion, however, regarding the temperature at which it is formed. Thus Klein2 notes that sillimanite forms only above 1300" C., while Mellor claims that it can develop below 1200" C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mel-lor's, the temperature rose from 800" to 1180" in 24 hr., and occupied the same time in cooling back to 800".

Jan 1, 1918

By Richard E. Gray, William S. McCann, Robert C. Speck, Robert W. Bruhyn

Subsidence of the ground surface is the inevitable result of high recovery longwall and room and pillar coal mining operations. Up to now, U.S. research into this phenomenon has been concerned primarily with documenting the magnitude and extent of ground movements and prediction of the attendant ground strains through traditional ap¬proaches that have been developed in Europe and the United Kingdom. Preoccupation with ground strain prediction has, unfortunately, diverted attention from the more meaningful objective of predicting the severity of damage to structures at ground surface and the prob¬able cost to repair such damage. An attempt has been made to rectify this situation by reviewing in detail one hundred thirty four cases of subsidence damage to dwellings above active mines in western Pennsylvania, identifying the types of damage and the circumstances under which damage took place. The data reveal that damage to dwellings virtually always includes basements in addition to the readily apparent effects to the superstructure. In 90 percent of the subsidence cases, more than half the repair cost is associated with damage to subgrade components. A damage classi¬fication system has been devised that relates observed damage to severity and repair cost in a uniform manner for conditions in the Northern Appalachian Coal Field. Damage severity has been examined in the context of depth to the mine, the character of the near¬ surface overburden materials, mining type and other parameters.

Jan 1, 1983

By Samuel Wyer

1. THE following is an abridgment of a recent report made by the author, covering an investigation of (A) The necessary use of natural-gas compressors; (B) The effect of gas compressors on natural-gas field operating conditions in Ohio, with special reference to the working pressure relations of gas wells of one company discharging by natural rock pressure flow without compressors, and adjacent wells of other companies, discharging into intake lines to gas-compressing stations. Tests were made at 107 different places in the counties of Fairfield, Licking and Knox, Ohio, which required 7,000 miles of automobile driving, and consumed 6 months' time. 2. A proper conception of. the necessary use and effect of natural-gas compressors in natural-gas production necessitates a clear understanding of certain fundamental definitions and judicial doctrines, which are given herein. 3. Gas is a fluid composed of a large number of molecules which are vehicles of energy continually in motion, and having an inherent. tendency to get farther and farther apart. The range of motion of the molecules is limited only by the volume of the closed containing vessel in which they constantly move to and fro. The most distinguishing characteristic of gas is its universal property of completely filling an inclosed space.

Jan 2, 1916

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.'s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

By J. E. Kemp

1. Situation.—From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway. which connects Monterey with Tampico. follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares. and from Linares one can see far away to the southeast the peaks of another group of mountains rising from the general plateau and forming a more eastern

Jan 1, 1906

Jan 1, 1882

By Luther W. Bahney

(San Francisco Meeting, October, 1911.) LIME is the alkali that is almost universally added to the solutions in the cyanide process of gold- and silver-extraction for maintaining the so-called, protective" alkalinity. It is produced by the burning of limestone. The value of lime for this purpose depends upon the percentage of calcium oxide contained, which is determined by three factors : 1, purity of the limestone used; 2, degree of the burning-temperature and the period of burning; and 3, length of time of storage of burned material and the condition stored, and whether it has been damp or wet during the storage. These three factors render uncertain the quality of lime bought in the open market. In the United States, lime bought from reliable manufacturers, who thoroughly burn a pure limestone and deliver at once to the consumer from the kilns, may be of a fairly-high and uniform composition ; but in Mexico and Central America, where it is purchased from many small producers, who often start with a poor grade of limestone and burn it in small crude kilns with as little fuel as possible, the quality of the product is quite variable. In consideration of the foregoing, it is apparent at once that there is a great need for a rapid technical method for the valuation of the lime to be used in a cyanide-plant. The determination of calcium by the gravimetric method, with the necessity of determining also the proportion of carbon dioxide, silica, and iron, requires too much time, and is usually out of the question for an isolated plant unequipped with a skilled chemist and, the necessary apparatus. The calculating of all the calcium so found to calcium oxide, although sometimes done, is manifestly very inaccurate.

Nov 1, 1911

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940