Search Documents

By D. J. Carney, R. R. Burt, E. J. Whittenberger

Hardenability (multiplying) factors for carbon, mongonese, silicon, chromium, nickel, and molybdenum have been developed for hypereutectoid low-alloy steels in which bainite is the first subcritical transformation product. These factors permit the calculation of 95, 80, and 50 pct martensite hardenability from chemical composition when steels with spheroidized structures are quenched from 1475°, 1525°, and 1575°F. The strong contributions to hardenability of the less expensive elements, silicon and manganese, suggest their use to obtain additional hardenability in hypereutectoid low-alloy steels. DURING the past decade a number of investigators'"11 have carefully developed information which permits calculation of the hardenability of medium -carbon low-alloy steels from chemical composition and grain size. These data have been especially valuable in developing less costly low-alloy steel compositions with equivalent or Improved

Jan 1, 1957

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-' during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By Leon W. Dupuy

A brief elemental discussion of the fundamental factors involved in diamond drilling often fills a need, particularly when a mine operator is contemplating for the first time an exploratory drilling campaign. Mr. James A. Barr, of the Mining Methods Committee of the Institute, has suggested that many engineers must undertake a drilling program of one kid or another and, in the case of diamond drilling, sometimes even are at a loss as to how to start correspondence. The Bureau of Mines has acquired much experience in managing exploratory diamond-drilling activities. Its activities in diamond drilling included exploring for potash in Texas, Utah and New Mexico1-' during the 1920's. The Strategic Minerals Exploration program was started in 1939 and was materially expanded during the war to include critical and essential minerals. At the peak of its war-time activity more than 200 engineers were employed, a majority of whom supervised diamond drilling. Many of them had little experience with such work prior to their employment with the Bureau, and it was necessary to instruct them in their duties. The purpose of this paper, therefore, is to present the fundamentals of exploratory diamond drilling from the viewpoint of management in such a way that they will Serve as a basis on which those beginning exploratory diamond drilling may build an experience and acquire ability to direct exploration as they gain that experience. Selection of Method of Drilling Selection of the method of drilling is governed by the type of material to be penetrated and by the type of sample needed to determine the quality and importance of a deposit. Types of drills that might be used for a given job include diamond drills, churn drills, hand auger drills, power auger drills, bucket drills, and rotary drills (sometimes called "seismograph rigs"). Each type has a specific field in which it is most useful. While the Bureau of Mines utilized all the types of drilling mentioned, diamond drilling was used on a majority of its exploratory projects. Factors Governing Selection of Diamond Drilling The prime consideration in selecting a method of drilling is first to determine what results are desired and then to choose a method that will furnish reliable data in the ground to be penetrated. Use of diamond drills permits recovery of a core as well as sludge at a comparatively low cost. The core provides an excellent means of studying the formation being drilled and furnishes much information that would be difficult to obtain otherwise. Diamond drills will recover a satis-

Jan 1, 1948

By David R. Mitchell

This paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual, it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenmenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and; izing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By David R. Mitchell

This paper is limited primarily to a description of dry coal-cleaning processes in which air currents are used to effectuate a separation between coal and refuse. Processes depending mainly on differences in the coefficient of friction, resilience and shape are not described unless the use of air is necessary for the proper functioning of the process. The air cleaning of coal is of primary importance to the coal industry of the United States. From figures presented in the 1941 edition Mechannual, it is estimated that at least 12 million tons of bituminous coal was cleaned in the United States during 1940 by machines using air as the separating medium. One of the current problems confronting the coal-preparation engineer is the dry cleaning of small sizes and slacks. Progress in machine development for the cleaning of small sizes has been slow in recent years in the United States of America; it has been much more rapid in Britain and on the European continent. This paper does not attempt an exhaustive survey of all these developments, and only machines and processes that have found considerable commercial application are cited. Further, no critical analysis has been made of the theory involved in the separation of coal from refuse by processes using air as the separating medium other than that necessary for an understanding of particular machine designs and applications. The possibility of using air for the separation of coal from refuse was recognized early by mining men and many attempts were made to develop commercial machines. The ingenuity of the early experimenters is to be marveled at in view of their lack of knowledge of the theoretical principles involved. As in other arts, practice has largely preceded theory. Yet, science and practice play a game of leap frog, now one ahead, then the other; the careful experimenmenter governs his efforts along practical lines by adapting his experiments to the limits prescribed by scientific laws. By first studying developments and the theory involved, it is not only possible to adapt processes to new uses but also to reduce materially operating cost and to build larger units without costly failures. Although many inventors have applied for patents for separating minerals by the use of air currents, the literature in regard to coal is meager. Berrisford2 describes briefly some of the early attempts to clean coal without the use of water. Several of the examples cited by him are reproduced herein. Fig. I shows a machine used for grinding and; izing, in which rollers running in a pan with a perforated bottom and fan opening on the side crushed the coal, which was then carried by the air currents to a settling chamber. The heaviest particles dropped out first and the light ones farthest away, as shown. In the year 1864, a machine was made that could be used as a sizer or to separate dirt from coal with a sized feed (Fig. 2).

Jan 1, 1942

By D. V. Doane, G. A. Timmons, W. G. Scholz

Molybdenum of high purity can be produced by direct dissociatiott of commercial molyhdenm disulfide in vacuo at 1600° to 1700°C (2910° to 3090°F). The Product is lower in oxygen than commercially available molybdenzdm powder. Analyses of ingots arc-cast from commercial molybdenum powder, hydrogen-re-cluced from animonium molybdate, and from thermally dissociated molybdenum disulfide indicate that the levels of chemical impurities in these ingots are similar. Equipment now in operation will produce 100-lb hatches of powder product. The paper describes development of processing equipment, control of processing varzahles, handling of the product, and evaluatiotl of the melal produced. MOLYBDENITE (molybdenum disulfide) can be decomposed by heat in the absence of oxygen to produce elemental molybdenum and sulfur, which is evolved as a gas. The temperatures required for the dissociation are above 1370°C (2500°F); the sulfur must be continuously withdrawn to permit the reaction to proceed to completion. This is accomplished by continuous evacuation of the thermal dissociation chamber and condensation of the gaseous sulfur in another part of the system. Cognizance of the fact that the dissociation takes place in two steps is important in controlling the process. Basically, the molybdenite dissociation process has two potential advantages as a method of produc- ing pure molybdenum: 1) The materials entering into the process contain little or no oxygen. Since the process is carried out in vacuum at high temperature, the quantities of interstitial oxygen, nitrogen, and hydrogen in the product should be very low. 2) The process is more direct than the commercia1 method of producing high-purity molybdenum. In the conventional process, molybdenite is roasted to molybdic oxide, the oxide is purified first by sublimation, then by conversion to ammonium molybdate, and finally, the molybdate is reduced in a hydrogen atmosphere (usually in two steps) to the metal lic molybdenum powder. This paper presents a description of the stages in scaling-up of the dissociation equipment and an account of attempts to evaluate the molybdenum produced by thermal dissociation, rather than a report of a fundamental study of the dissociation reaction. Since little has been written on the subject, it is appropriate, before detailing the development of the process, to review briefly the research that has been conducted over quite a period of years. LITERATURE SURVEY The first accounts of the possibility of thermal dissociation of the mineral molybdenite were re-

Jan 1, 1962

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

By M. W. Fabjanczyk, E. G. Alexander

INTRODUCTION The purpose of this paper is to summarise development of design processes used in the 1100 oreoody as a result of experience encountered. Design methods have been developed as a result of the history of ground behaviour, free-standing qualities of cemented back fill and mass blasting techniques. This paper contains an historical review of design methods previously described by Matthews ( 1972 ) , Hornsby and Sullivan (1977 and 19781, Kirkby, Blair and Hutton (19781, and Stewart (1980). The reasoning behind design philosphy changes are discussed and placed into context with methods now adopted. The 1100 orebody is Mount Isa's main producer of copper ore (5 million tonnes per year ) . Proven reserves are 120 million tonnes at 3.2% Cu. Location of the 1100 orebody in relation to overall mine geometry was well described by Dayton (1976). Geology The orebody is located in a series of massive brecciated shale lenses, in either a siliceous or dolomitic matrix, surrounded and separated by a uniform shale sequence. The whole formation is truncated at depth by a faulted contact with a greenschist facies metamorphic sequence below (Figure 1 and Figure 2) Mathias and Clark (1976). The breccia is known locally as silica dolomite and contains nearly all the economic mineralisation. Interfingering of shale and breccia often results in irregular boundaries to the silica dolomite and the ore limits. Geometry The geometry of the orebodies is shown by Figures 1, 2 and 3. Figure 3 also shows the location of the copper orebodies in relation to the lead orebodies. Structure Although the orebody is contained within the massive breccia (u.c.s. 150-250 MPa), it is cut by shear zones sub-parallel to the regional bedding (north-south striking, dipping approximately 60o to the west), and diagonally by major transverse faults (Figure A). These major faults have continuity in excess of 300 metres, with varying amounts of displacement up to 200 metres, and are zones of potential movement.

Jan 1, 1981

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By Wilbur H. Grant

THE property of the United Comstock Mines Co. lies in the eastern foot-hills of the Sierra Nevada Mountains, in the Washoe mining district of Storey County, Nev. Commencing at the boundary line between Virginia City and Gold Hill, covering all the town of Gold Hill, it extends south to American Flat; the main camp, or the new town of Comstock, the mills, shops, residences of employees, and the main haulage-tunnel portal are located on American Flat. The property extends for about 10,300 ft. along the lode; this covers the southern end of the main Comstock lode, the Knickerbocker branch, and the junction of the Silver City branch with the Comstock lode. Within the property, 5000 ft. of the main Comstock lode is known to have been productive, 1000 ft. of the lode at the northern end of the property is thoroughly developed, and 1000 ft. south of this is partly developed; this leaves about 3000 ft. of the known productive portion that has not been opened up by this company. The northern end of the property, or the Imperial mine, has been intricately developed by five main levels and numerous sublevels. The Yellow Jacket ground to the south has been partly developed by the reopening of three old levels. In addition, the main haulage level is driven from the portal at Comstock for 9250 ft., to the north end of the property; about 5500 ft. of this `is in the foot wall of the lode and parallel to it.

Jan 11, 1922

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

By H. F. Perkins

CORROSION as an economic problem is growing rapidly in importance not only because it entails a replacement of corroded parts, but because it interrupts operation and causes hazards of damage and injury through failures of corroded equipment. Nearly all industries are interested in this subject. This paper, although concerned chiefly with corrosion in a complete refinery on the sea coast, discusses many of the various forms of chemical decomposition, most of which are found universally. The petroleum refining industry, in the writer's opinion, is seriously afflicted by the presence of sulfur in nearly all crude oils. The complete removal of sulfur from the crude as it enters the plant would cause such a relief from corrosion that this problem for research would seem to demand active attention. Next to sulfur the most troublesome corrosive agent is the saltmagnesium chloride, found in the water associated with crude oil, the last traces of which are so difficult to remove. This is much less serious, however, than the sulfur. Refinery corrosion can be tabulated as follows: Causes of Corrosion and Places of Attack in a Refinery CORROSIVE ELEMENTS MATERIAL ATTACKED Air: Pipe lines Moisture Tanks COQ Electric fixtures Sulfur gases Still towers Chlorine Condenser boxes Other acid-forming gases Ladders and stairs Smoke stacks Steel buildings All exposed metal Water: Alkali Fire lines and hydrants Acids Cooling water lines Air Condensers and coolers Other dissolved gases Boiler tubes Steam Steam pipes and valves Turbines Oil Sulfur compounds Tanks, pipes, valves, stills, towers MgCl2-Hydrochloric acid Condensers Air contamination

Jan 12, 1926

By H. H. Kaveler

Education is for the purpose of developing citizenship, and, if it is pursued for the additional purpose of preparing for a professional career, such as engineering, it is also directed to developing a knowledge of essential science, aptitude for the application of science to practical situations, and a knowledge of the industrial art in which the engineer will be engaged. The process of education required for engineering must of necessity extend beyond the classroom into industry. For that reason, the education of engineers should be divided as between the university and industry. Specialization in engineering should logically come as a result of experience in an industry. The student cannot take the time in a university, and, the university cannot teach the skills required to develop a specialist without sacrifice to the more essential broad purposes of formal education. In addition to talent in science, aptitude in the application of scientific fact, and knowledge of the industrial art, the engineer should possess certain personal qualities which are helpful in the pursuit of a professional career. Those personal qualities are: the ability to work as a partner in an enterprise, the ability to do jobs in a way whereby job performance is a means of gaining experience and increased responsibility, the capacity to write and speak in an understandable manner, and, a Proper regard for the "significance of answers." These pcrsOnal qualities may be of almost equal importance to acabemic accomplishments in the field of science. Development of such personal qualities are an essential part of the student's training in the university and in industry. They can be developed effectively through the leadership of instructors. Compulsory Education Nature played a mean trick On the human race when the evolutionary Process failed to develop in the individual a capacity to inherit knowledge. Were knowledge transmissible in a cumulative manner from generation to generation, mankind would be by inheritance wise beyond measure within a few generations. Then there would be little if any need for a "system of education." As matters stand, however, all must suffer the burden of starting life at the "zero " level of learning from which station each rises depending upon individual capacity to assimilate knowledge left of record by our predecessors and the individual effort exerted to compensate for Nature's failure to endow the offspring with intelligence. In the United States some degree of education is generally regarded as essential and necessary. Therefore, all citizens are subjected by law to an educational process covering the primary school age from six to sixteen years. Beyond the schooling required by law, many attend secondary schools, and beyond that, schools of higher learning. Our standard of living is at a level that permits an increasingly large fraction of the population the opportunity to go through all of the formal educational process. As a result, education in the colleges and universities has almost reached a mass production level. In spite of the high

Jan 1, 1949

By M. R. Goldick

THE Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5 1/2-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mechanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. ORE TREATED Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopyrite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (90 pct minus-200 mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1947