Search Documents

By T. H. Troller

FOR a long time propeller-type fans have been considered a very adequate means to move great quantities of air against small static pres-sures. They have been in use for this purpose in mines, as well as in other installations. For static pressures of over 2 or 3 in. of water, the centrifugal blower almost ruled the field until very recently. Some attempts were made to use a number of propellers in line. Such arrange-ments made it possible to obtain pressures higher than 2 in. of water, but they complicated the construction and increased its expense, and the efficiencies were not improved. The more recent development of propeller-type fans has been decidedly influenced by the intensive aerodynamic research in connection with aeronautical development, which has taught us, in particular, how to use airfoils properly. The characteristic that makes an airfoil so valuable is the fact that when it moves through the air a high force component, the "lift," acts on it vertical to the motion, while the "drag" in the direction of the flow is small. The ratio of lift to drag is approximately 20 to 1 at the angles at which the profile is used in practice. An element of the turning blade, the movement of which, relative to the air, is mainly in the direction of the plane of rotation, thus experiences only a small "drag" FIG. 1.-DIAGRAM OF FORCES ON WING SECTION. opposing its rotation, and for this reason a relatively small torque is required at the driving shaft. At the same time there is a strong force component at 90° to the plane of rotation. This force is parallel to the propeller axis in the direction opposite to that of the flow of air, with a correspondingly high pressure increase.

Jan 1, 1936

By Rex W. Woods, Morris Muskat

A leastmsquare analysis procedure has been developed and applied for the study of the deviations in estimations of oil in place as given by the material-balance equations. The data used were those obtained from field observations on the Jones sand in the Schuler pool, Arkansas, and the Monroe dolomite in the Reed City pool, Michigan. Possible effects of water intrusion were taken into account by expressing the cumulative water influx in terms of various functions previously proposed in the literature. Formulas were developed and values calculated for the minimum deviations and minimal percentage deviations in the calculated volumes of oil in place from the average values, as could be obtained by suitable choice of the water encroachment and initial gas-cap volume parameters. The results show that the fluctuations in these calculated volumes are very insensitive to the values chosen for the rate of water intrusion and initial gas-cap volume, and hence cannot be safely used in discriminating between spurious values for these parameters and such as actually pertain to the producing reservoirs. Moreover, the exact form of the water-intrusion function seems to have but little effect on the fluctuations in the computed oil in place. Accordingly, it is concluded that the material-balance method does not of itself provide a satisfactory criterion for determining the basic physical unknowns of producing reservoirs or in making conclusive decisions regarding the production mechanism, unless independently established geological control data are available for eliminating unreasonable values for the reservoir parameters, even though they may still satisfy the material-balance formulas. If, however, from core or logging data the initial oil in place and the gas-cap volume can be established in advance, the material-balance formulas can be inverted to find the water intrusion. Moreover, by determining by such calculations the water-intrusion coefficient, the iuture production performance can then be predicted by the aid of the materiaI-balance formulas for specified operating conditions. This type of application may be of particular value in predicting the results of Pressure-maintenance operations. Introduction The evaluation of the forces acting upon an oil reservoir is a problem of considerable interest to the operator as an aid in determining the proper method of operation for the reservoir to obtain an optimum recovery of oil. In many pools, the nature and magnitude of the forces acting upon the reservoir remain unknown until an appreciable amount of ultimate recovery is obtained. To be of value to the operator, a reliable interpretation of reservoir performance should be available in the early life of the pool to permit an optimum plan of operation. Progress has been made in an understanding of reservoir behavior and the importance of the different factors involved. The material-balance method of estimating oil in place has been proposed as a tool in analyzing reservoir-performance problems.l The solution of such problems by this method ordinarily involves two or more unknown values relating to the nature of the reservoir, and the results

Jan 1, 1945

By Arthur Phillips

The progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yielding supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with particular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weertsl recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150" and 225' C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler and Sachs,2 who indicated a parameter value, for the same alloy annealed for 24 hr. at 200° C., some 0.0008Å. larger than that of pure aluminum. Stenzel and Weerts attributed the abnormal lattice dimension to the effect of strain induced by the precipitation of CuA12. Weerts3 later

Jan 1, 1934

By G. H. Edmunds, C. H. Mathewson

About fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211). Attempts to develop the structure of the bands by various methods SO that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent, of niekel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form (211). Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form (211) as sketched in Fig. 2. Rosenhain and McMinn4 in 1925, after a careful study of slip bands in ferrite containing Neumanns previously produced by shock, concluded

By Donald C. Barton

Success in the use of the Eötvös torsion balance method of mapping geologic structure depends largely on the accuracy in the interpretation of the observed results. Skill in that interpretation depends (1) on the knowledge of the types of the variation of gravity, the gradient of gravity horizontally, and of the differential curvature produced by bodies of different sizes, shapes, dimensions, and densities; (2) on the knowledge of the possible types of structural bodies which might produce the observed anomalies; (3) on the empirical knowledge gained by experience not only in the geological interpretation of torsion balance surveys, hut of interpretations of inadequate geological data; and (4) on a knowledge of the possible and probable types of geologic structures in the area of the survey. The knowledge of the anomaly which a known body will produce and conversely the knowledge of the body or bodies which will produce a known anomaly may be gained by empirical experience and by mathematical study. The knowledge gained by empirical experience is fragmentary and inexact. The geology of most structures actually is known very superficially. The surface geology may be known accurately. If the structure is petroliferous, the subsurface geology of the oil field will be known down to 3000, 4000, 5000 ft. or in a few oil fields down to 7500 ft., but the deeper geology will be unknown and the metamorphic, igneous, or massive limestone basement below the reach of the drill may contrast sharply in density with the overlying sediments. Away from the oil field, the subsurface geology is known only from scattered drill holes, which do not go to the basement. A fair but not necessarily accurate knowledge of the geology of the nonproductive area can be obtained by correlation of the wells but the degree of its accuracy in general is proportional to the density of the occurrence of the wells. The geology below the bottom of the wells however is unknown. An anomaly mapped by the torsion balance is the sum of the effects of the contrasts in mass of its whole geologic surroundings. If the dimensions of a body of abnormal density are large enough, depth or distance makes no difference in the effects on the gradient and differential curvature; and as a matter of fact, in many places, the basement and irregulari-

Jan 1, 1929

By David White

THE search for potash salts in the great "Red Beds? region of the Southwest, conducted for several years by the U. S. Geological Survey, the work being carried on for a part of the time in coöperation with the Bureau of Economic Geology and Technology of the University of Texas, has resulted in the discovery, within shafting depth, of potash salts, apparently of workable thickness and commercial quality, and prob-ably of great extent. Definite information is lacking as to the exact thickness of the potash beds, the size and boundaries of the areas underlain by workable strata, and the locations of the deposits richest and most favorably situated for exploitation. Briefly to review the salient features, of the general situation: We have in the great Red Beds region of the southwestern United States, embracing portions of central Kansas, western Oklahoma, eastern New Mexico, and northern and western Texas, .a series of sandstones. shales, anhydrite beds, clays and limestones, which; through an interval of 1000 ft., more or less, carry beds of salt, estimated by Darton1 to contain over 30,000 billions of tons of rock salt. It is the greatest known salt field of the world. At some points the intercalated beds of rock salt, one of which is reported by the driller to exceed 300 ft. in thickness, aggregate, accord-ing to the drillers' records, over 1000 ft. The sedi-mentary strata are similar in composition to those carrying the potash deposits of western Europe, and they were laid down at the same time and under condi-tions which, in many respects at least, were similar The stratigraphy and character of the beds are des-cribed by Darton2 and a, part of the area and the reported aggregate thicknesses of salt are shown, with some revision after Darton, in the accompanying map Fig. 1. The assumption that in the great areas of shallow evaporation basins spread over -the vast base-level region of saline deposition in the Southwest during Permo-Triassic time, potash salts were in some places, and at different stages, thrown down in crystalline deposits associated with the beds of rock salt, anhydrite, and gypsum, is, geologically speaking, more than reason-able. They are to be expected, and the conviction that they are probably present has long been held both in the Texas Bureau of Economic Geology and Tech-nology, under Dr. J. A. Udden, and in the- U. S. Geological Survey. Accordingly, for many years, efforts to determine whether potash deposits are present in this region have been made, though under very great difficulties, such as insufficient funds for boring, hack of drilling on private initiative in the more promising regions, hack of interest at first on the part of the drillers and companies, and, hater, inadequacy both of the methods of boring and of the sampling, to reveal in definite terms the thickness-of any saline stratum of given composition.

Jan 4, 1922

By J. W. Pamplin

SOME 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca3P20s) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix, Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by ½ mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, some-times a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix-1000 yd. in all-amounts to about 1500 tons of material moved each hour. The over-burden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7 ½ long tons in 4000 gal. of water per minute-a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By Simon D. Strauss

COPPER In terms of mining activity, copper is the leading nonferrous metal. It is true that in recent years the volume of aluminum consumption in the non-Communist world has exceeded the volume of copper consumption, but virtually the entire primary aluminum supply is derived from bauxite. On the average, only four tons of bauxite need be mined to produce a ton of aluminum. By contrast, the highest-grade, large-scale copper mines now in operation (those in the Congo) must mine at least 20 tons of ore to produce a ton of copper. In the United States an average of 150 tons of ore must be mined to produce a ton of copper. This does not take into account the huge amounts of waste overburden that must be stripped from the open-pit mines to account for their steadily rising share of the world's copper output. Copper epitomizes the economic problems of the mining industry in many ways. Its price is highly volatile, considering its great economic importance. It has been a tool of mankind longer than any other of the base metals-the dawn of history has been classified as "The Bronze Age." World Copper Production Although copper is mined in many countries, in recent years 70% of the non-Communist world production has come from six countries. Two of these are industrialized countries and are large consumers-United States and Canada. The other four are developing countries with very small domestic requirements-Chile, Zambia, Zaire, and Peru. Heavily dependent on copper exports to sustain their domestic economies, these countries find themselves oscillating between prosperity and depression with the changing levels of copper prices. In an effort to control their own destiny, in 1968 they formed an organization of copper exporting countries (CIPEC) which was designed to study copper markets and possibly to intervene actively in these markets. (When this chapter was being prepared, no actual steps along such lines had been taken.) Many of the leading industrialized nations are wholly dependent on imports for their primary copper supplies. These include West Germany, the United Kingdom, France, Italy, and many others. Japan, now the non-Communist world's second largest copper consumer, produces only 10 to 15% of its requirements from domestic mines. Although the bulk of the copper output is smelted in the country where it is mined, there is a limited international trade in copper concentrates. Canada, the Philippines, Australia, and Papua-New Guinea are significant exporters of copper concentrates; Japan, Germany, the United States, and Sweden are importers. However, this trade accounted for only about 10% of the non-Communist world production of copper during the decade of the 1960s.

Jan 1, 1976

By C. W. MacGregor

In the testing of materials there exist various methods of recording graphically the behavior of a material subjected to tensile stress. Probably the most common method is to plot the tensile stress So, obtained by dividing the load P by the original area of cross section A0 at the start of the test, as a function of the strain e0, which is obtained by dividing the ?Lo or the change in the gauge length by the original gauge length Lo. A list of the symbols used here is given in Table 1. This method, while it has proved useful in the routine testing and comparison of various materials, does not have a very sound physical basis, as was first pointed out by P. Ludwikl, and consequently does not afford a very deep insight into the true physical behavior of the material under stress. Among the objections to this method may be mentioned: (1) that by dividing the load P at any stage of the test by the original area A. a fictitious stress is obtained, which does not actually exist; (2) that the strain e0 = ?L0 is not an exact expression for the true strain for large values of ?LO in per cent of Lo; (3) that when necking starts the strain varies considerably along the gauge length and the above expression no longer gives the true strain existing at any point on the outside of the bar; and (4) that the axial strain varies over the cross section of the necked portion and e0 does not represent an average of these strains over the cross section. Stresses taken from such a diagram would be only approximate and, if used to compare results of a test on a given material under simple tension with results obtained under combined stresses, certain errors would be thus introduced. In order to overcome some of these objections, various methods have been suggested, both as to the quantities to be measured and as to their graphical representation. In some cases the so-called "true stress," obtained by dividing the load P by the actual area of cross section A existing when the load P was applied, is plotted as a function of the strain

Jan 1, 1937

By F. J. Lecznar

An investigation of the problem of separating two minerals by a moving inclined plane has revealed that only minerals with considerable difference in sliding friction coefficients separate readily; that it is possible to separate two minerals when only one of them has a rolling friction coefficient; that difference in geometrical shape of the minerals is important to separation which improves as grain size increases; and that the thickness of the stream falling on the belt influences the grade of separation - the thinner the stream, the smaller the interference between the grains of the minerals to be separated and the higher the degree of separation. The problem of separating two minerals with different friction coefficients and shapes by a moving inclined plane has been investigated. Friction separators can be used to separate two materials that differ in shape and in friction coefficient. 1,3 Gladkov has presented some theoretical aspects of using a moving plane to clean corn and podded seeds; this method, however, did not result in practical application. When considering the separation of minerals, only those with considerable difference in sliding friction coefficients can be taken into account. Furthermore, it is possible to separate two minerals when only one of them has a rolling friction coefficient. The difference in geometrical shape of two minerals is also important to separation. It has been found that the separation of two minerals improves as the grain size increases. For example, coal and slate over 2 in. in grain size separate much better than materials of smaller grain size. As Table I indicates, the slate grains smaller than 25 mm gradually lose their flat shape with decreases in size and are more rounded than larger grains, which are almost flat. The smallest grains of slate in first and second fractions slide down the belt since their friction coefficients decrease and approach the value of the rolling coefficient. The percentage of separation of the first fraction is, therefore, low. Thickness of the coal stream falling on the belt also influences the grade of separation; the thinner the stream, the smaller the interference between the grains of the two minerals to be separated and the higher the degree of separation.

Jan 1, 1963

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By T. A. Rickard

The province of Otago consists, roughly speaking, of the southern half of the South Island* of New Zealand. On three sides it is washed by the Pacific Ocean and on the north it abuts against Westland and Canterbury. It covers an area of over 20,000 square miles, and for the most part has an extremely broken surface; the narrow plains of the sea-board are bounded by the rounded foothills which in turn are overlooked by range after range of the snowy summits whose varied beauty has made the island known as the Switzerland of the southern hemisphere. The gold-fields are confined to the quartzose schists which, in a broad band, 70 to 75 miles wide, cross the district, extending in a northwesterly direction from the shore of the western ocean into the northern provinces. These quartzose schists are the characteristic rocks of Otago, and to their curious structure are due the interesting differences exhibited by the mining districts in the modes of occurrence of the gold. These rocks, which are almost unbroken over their full extent, have been divided by the Provincial Geologist, F. W. Hutton, into two series of beds, named respectively the Wanaka and Kakanui formations. The only reason given for this division is the desire " to divide such an enormous thickness of rocks in order that the map might display somewhat of the geological structure of the district." As Hutton and others have pointed out, there is in fact no dividing line. The changes noticeable in the ascending series of schists are very gradual, and are due to the slowly decreasing effects of metamorphism. Hutton estimates the thickness of the Wanaka series at as much as 50,000 feet, and the

Jan 1, 1893

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949

By E. A. Barnard

ARSENIC is a very old substance. The ancients speak of it in their writings, and its use has developed very little until recent years. The ancients used it in making pigments, in medicine, and for poison. They also tell of the difficulties of handling it-an experience which is very similar to our own. Until about 10 years ago, arsenic was very cheap and was a drug on the market. About that time the boll weevil began making serious inroads on the American cotton crops, and after much investigation the Depart-ment of Agriculture developed a very successful poison for this pest, consisting of calcium arsenate. The weevil pest has continued, and as the cotton planters have become convinced that calcium arsenate is the best material to use against the weevil, the demands for it have been steadily increasing, resulting not only in a rising price of arsenic but in a very serious shortage so far as our country is concerned. So serious has this shortage become, and so vital is it to the cotton growing industry, that Congress has appointed a committee to investigate and report on the situation. A meeting of arsenic producers and consumers was held in New York last December to take stock of the situation and to see what could be done. The extreme increase in, the market price of arsenic-from 6 c. to 15 c. per lb. in less than a year-has been very harmful to the producers as well as to the consumers. Some very interesting' data were brought out at this meeting, as follows: CONSUMPTION PER YEAR, SHORT TONS Arsenate of lead 2,000 Paris green 1,200 Proprietary mixtures 750 Sheep dips : 1,000 Weed killers 1,500 Glass : 2,000 8,450 1922 Consumption as calcium arsenate 4,000 12,450 1923 Estimated consumption as calcium arsenate... 12,000 Estimated 1923 consumption 20,450

Jan 8, 1923

By Charles J. Potter

There are many sources of energy available for consumption. Some available are solar, tide and wind. However, in terms of relatively large usage, only four principal sources are used for primary energy today. They are coal, oil, natural gas and water power. Such additional items as wood and nuclear energy, although supplying quantities of energy today, do not in the aggregate amount to any real significant quantity, but nuclear energy must be considered for future use. In addition, such a thing as gas from distillation of coal and oil is not considered primary energy. The principal markets for primary energy are the electric power utilities, space heating, industrial uses and transportation. The electric utility use of energy is primarily from coal, followed by natural gas and water power. Space heating is primarily a gas market, followed by oil and then coal. Space heating by electricity is only considered in the generation of electric power. Transportation's principal source of energy is oil. Coal has practically no market left in this field.

Jan 4, 1962

By A. C. Watts

For several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to one million cubic feet of methane every 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside, after all men and animals were outside, had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the placc at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft, from the shot-firers' switch outside the mine and the most remote working face was 2½ miles. The various working faces were scattered over a wide area between these two points. A description of the main power line would be valueless; the conductors were of sufficient size, the drop in voltage being not more than

Jan 1, 1927

By G. W. King, A. Bogrow, L. F. Marek

The purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction of FeO to Fe. Unless the gas has a CO!CO, ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles .at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available): the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity of the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"—i.e., the efficiency of conversion of the "available" CO supplied— is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1948

By L. F. Marek, G. W. King, A. Bogrow

The purpose of this paper is to present the data and some interpretation of the results of a laboratory study of the reduction of iron ore and the deposition of carbon from the reducing gas mixtures in such reductions. One major object of the study was to determine the effect of gas pressures on these chemical processes. Effort was made to approximate the conditions of temperature, gas composition, linear and mass gas velocities, pressure range, and extent of reduction prevailing in commercial blast furnaces. The results show that the reduction of Fe203 proceeds by two steps, largely consecutive under the conditions used herein: reduction of Fe203 to FeO, and reduction of FeO to Fe. Unless the gas has a CO!CO, ratio greater than 2.1 only the first step occurs under these conditions (850°C) but the following generalizations apply to either step or to the combination. The rate of reduction of relatively fine ore particles .at any time is proportional to the mass rate of supply of CO (provided some of it is thermodynamically available): the rate therefore is proportional to the linear velocity at constant pressure, or to the pressure at constant linear velocity. Thus, the rate of reduction may be increased without increase in linear velocity of the reducing gas by increasing the mass velocity of the gas and increasing the pressure correspondingly to avoid any increase in the linear velocity. The rate "constants"—i.e., the efficiency of conversion of the "available" CO supplied— is not actually constant but decreases as the reduction proceeds, and is a function only of the state of the ore; i.e., of the amount of reduction already accomplished and hence of the amount of CO passed. The particle size of ore used in nearly all the experiments was relatively small (8 to 14-mesh). The rate of reduction in run 16 with 3 to 8-mesh ore particles is within experimental error the same as with the finer ore. Although this would indicate an absence of effect due to particle size in this range of ore particles, it is desirable to have more data on other ore sizes and on ore of different densities before arriving at any generalizations on this point. Although it is possible to extend the analysis of these results to consideration of the more detailed kinetics and mechanism of iron oxide reduction, such extension is beyond the scope of the present paper. From the experiments on carbon deposition, it was evident that if carbon deposition is increased at all by the application of pressures up to 10 psi ga., such increase appears to be less than the experimental and analytical error. It appears safe to conclude that at top pressures on the order

Jan 1, 1948

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958