Search Documents

A study was undertaken to investigate the relationship between the quantity and value of economic demonstrated resources discovered for 12 mineral commodities over a ten year period and the expenditure required to yield such mineable resources. The results showed that for every dollar spent on exploration, there is an apparent in-ground average value of around $54 dollars contained in the economic resources found. While this appears to be a satisfactory return, it should be remembered that more than 99.9% of exploration programs are judged to be failures because a viable ore body or mineral deposit was not proved up. What is behind this seeming paradox?   The fundamental truth behind mineral exploration is the fact that the more you explore, the more you find, and that one success will often lead to further discoveries. It appears that one rich and viable deposit creates such surplus that its inherent high value ('the pot of gold') makes up for all the failures. In short, mineral exploration is a high risk business with uncertain returns. However, with skill, enthusiasm, experience and venture capital, it can yield larger than normal returns for the brave and the fortunate.   Analysis of exploration expenditure and economic resources discovered for the period 1987 to 1996 revealed that the apparent in-ground value of economic ore discovered per dollar of exploration expenditure varied from a high of $429 for iron ore and $261 for bauxite to a low of $22 for gold and for lead, and $5 per dollar of diamond exploration expenditure. Preliminary conclusions drawn on the reasons for the variations observed include the inherent ease or difficulty of discovery for different mineral commodities which may in some cases, relate to the natural prospectivity of Australia as a whole. Layered deposits like iron ore and bauxite appear to yield higher in-ground value returns on the exploration dollar. To some explorationists, this may be considered as seemingly obvious, but it may have more to do with very large-exploration tenement grants pursued by various Australian State Governments in the early 1950s and 1960s than the apparent ease of delineating a stratabound deposit.   Despite the apparent relatively low in-ground value produced by the gold exploration dollar of $22, the 5660 tonnes of gold discovered in this ten year period was worth $9.1 billion and representing over a quarter of the new mineral wealth created in the ten years to 1996. This contribution, along with that from the other minerals discovered over the period, led to a significant boost to Australia's export income and standard of living.   It is concluded that, given the nexus between the amount of mineral exploration expenditure and the quantity of new resources likely to be discovered, this knowledge may help policy makers seek to influence the rate of resource discovery in countries like Australia for the benefit of the nation.

Jan 1, 2004

By M D. Taylor, G Duclaux, K Atkinson, L A. Fisher, A R. Latham, M F. Gazley, S J. de Beer, C M. Tutt

Geological logging by mine and exploration geologists involves the application of a logging code that requires a geologist to make a subjective decision to classify a particular rock unit. This will most likely result in inconsistencies in logging that will be difficult to monitor or assess over time. A potential solution to this problem is to have an objective method to determine the true nature of a given rock unit. This can be achieved using portable X-ray fluorescence technology (pXRF), as large geochemical data sets can be collected rapidly and at low cost. Plutonic Gold Mine (Plutonic), Western Australia, has a growing data set of more than 150 000 pXRF multi-element analyses from core and underground face samples, reconciled to Au fire-assay concentration, and logging codes. This study investigates and statistically validates the consistency with which the logging codes have been applied at Plutonic for the last four years, with respect to both Au distribution and other elements. In doing so, we have developed a schema that allows objective logging to occur once core has been sent for assay and analysed by pXRF. While far from replacing the geologist in the field, this is a complementary method that adds significant value to a data set.CITATION:Gazley, M F, Tutt, C M, Latham, A R, Duclaux, G, Fisher, L A, Taylor, M D, de Beer, S J and Atkinson, K, 2013. Objective geological logging using geochemical multi-element data - Plutonic Gold Mine, Western Australia, in Proceedings World Gold 2013 , pp 455-462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

From time to time failures occur in structures made of lead, and the failure may be due to corrosion involving a definite thinning of the lead sheet, or it may be of such a nature that cracks develop and the lead appears to disintegrate. The idea of lead cracking will at once suggest something abnormal, for common experience shows that this metal is very ductile and will withstand considerable bending without showing any sign of fracture. Cracking, on the other hand, is usually associated with brittleness.Fig. 1 is a natural-size photograph of a cracked sheet of lead. Prior to photographing, the sheet was etched byimmersion in a solution of ammonium molybdate. Several characteristics of this crack will be evident. First of all it is distinctly a zigzag crack, and secondly it passes between, rather than through, certain well-defined areas which appear bright in the photograph. This is particularly noticeable at the lower end where the crack appears to terminate.

Jan 1, 1932

By G T. Jemwa, F Rousseau, F J. Wolfaardt, J A. M Rademan, P W. Smit

Mining companies are increasingly faced with the challenge of reducing operating costs while maximising throughput and profitability. At the same time, the grade and quality of treated ores are becoming poorer and more variable, resulting in suboptimal process performance.It is now widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In particular, progress in plant automation and control systems has seen a trend towards unified frameworks for control and optimisation of mineral processing plants. These frameworks seek to seamlessly integrate different roles and tasks involved in process operations - IT, automation, plant maintenance and operations. An integrated solution framework for reducing process variability, increasing process efficiencies and maximising plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis ægapÆ evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.Resolving these problems can potentially avoid unplanned downtimes, process instabilities and other operational surprises, thus ensuring optimal plant throughput and optimal process behaviour for improved recoveries. Integrating control systems and plant automation with advanced analytics to analyse and optimise processes enables operations to achieve reductions in the variability of key process parameters. In addition, early detection of equipment malfunction or suboptimal process conditions leads to improved equipment availability and reliability. Ultimately, these operational gains reflect in profitability because of plant throughput and recovery gains. These benefits are demonstrated using data from a South African gold mining operation, where such an integrated asset and process health monitoring framework for process optimisation has been implemented.CITATION:Jemwa, G T, Wolfaardt, F J, Smit, P W, Rademan, J A M and Rousseau, F, 2013. Towards an integrated framework for asset and process health monitoring and optimisation on a milling circuit, in Proceedings World Gold 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Nguyen T. T, Williams A. M, Siauw T. H

During the last 20 years the CSIRO Division of Manufacturing Technology, through its research and development program, has made a substantial contribution towards understanding the pressure die casting process. Much of this work focused on the hot chamber die casting of zinc, where the importance of achieving optimum flow of metal into the die cavity, combined with the correct thermal balance of the tool, is critical to the production of high quality castings. Having developed a fuller understanding of the heat and fluid flow occurring in the pressure die casting process, CSIRO sought to make this information available to the industry in a form where it could be readily used by die casting engineers. This led to the development of DMT-CASTFLOW and DMT-CASTHERM, two unique, PC-based, die design software packages. DMT-CASTFLOW provides facilities for designing running and gating systems while DMT-CASTHERM enables the die designer to optimise the cooling and/or heating requirements of the die. These two packages are now being sold internationally. This paper will describe some of the major features and benefits that can be derived by using DMT-CASTFLOW and DMT-CASTHERM panicularly in the design of zinc pressure die casting dies.

Jan 1, 1993

Use of Impact Crushing for the Enrichment of Low-Grade Colemanite Concentrates This paper presents the results of an investigation into the enrichment of -25+3 mm low grade colemanite concentrates exploiting differential breakage properties of various minerals associated within the ore sample. Boric acid production process requires concentrates containing at least 42 per cent B2O3, hence concentrates below this grade either stock piled or further treated to increase B2O3 content. The low grade concentrate is obtained as a by-product of Emet Colemanite Concentrator and the B2O3 content may vary around 37 - 38 per cent. The sample used in the experimental studies assays 37.52 per cent B2O3. In the experimental procedures the sample was crushed using a laboratory size horizontal shaft impact crusher and the products were classified into different size fractions by screening so that any improvement by size could be observed. In the tests the effects of parameters such as the revolution speed of the crusher and heat treatment was checked. Test results prove that boron contents show a tendency to increase as the particle size decreases. As a result of the experimental studies a colemanite concentrate assaying 42.13 per cent B2O3 is produced with 76.55  per cent recovery. Arsenic content is seen to change inversely proportional with the B2O3 content of the concentrate such that it drops from 1016 ppm from the as received sample to 676 ppm in the concentrate.

Sep 13, 2010

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By L R. Sousa, M He

Rock burst is common in deep underground excavations and is characterised by a violent ejection of block rocks from excavation walls. It is critical to understand the phenomenon of rock burst and particularly the failure mechanism. Laboratory experiments are one of the ways. For that purpose, a rock burst laboratory test system was developed at the State Key Laboratory for Geomechanics and Deep Underground Engineering at the China University of Mining and Technology, Beijing. A true triaxial test system, designated the Deep Underground Rock Burst Analogue Test Machine, was developed, which can transfer a stress state from three-direction-compression on six surfaces to the compression on five surfaces with one set free. The rock burst experimental system comprises an acquisition of acoustic emission signals, a high-speed recording in order to accurately record the kinetic characteristics of rock fragments ejected during a rock burst event and the possibility of infrared thermography showing the surface temperature of the samples. In this paper, analyses of typical results from rock burst tests are presented with a description of the obtained results. The mechanisms of rock burst are illustrated, and a rock burst classification is proposed based on these laboratory tests. For the control of rock burst, the constant resistance, large deformation (CRLD) bolt or anchor is presented for accommodating the large displacement of surrounding rock masses and absorbing the impact of the sudden release of rock burst while outputting a constant resistant force in response to the external load. The CRLD bolt or anchor has had practical applications in underground mines. Finally, in situ tests performed in a tunnel at Qingshui coalmine, China, are analysed in detail.CITATION:He, M and Sousa, L R, 2014. Experiments on rock burst and its control, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 19–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

This paper identifies the challenges and opportunities for mining companies and communities in investing in human rights compatible, credible, effective and representative company-community relationships.   The paper draws on the work of Professor John Ruggie, Special Representative to the United Nations Secretary General on Business and Human Rights, and his Protect, Respect and Remedy framework for business and human rights, The CDA Collaborative Learning Project, and the experience of Oxfam Australia. This paper begins with the premise that Australian companies commence operations offshore with high expectations and a willingness to work harmoniously with local communities. However, as companies increasingly engage in global operations - particularly in weak governance and conflict zones - the challenge to establish and sustain rights compatible, meaningful, corporate community relationships and grievances mechanisms becomes both more complex and necessary. Establishing trust and honouring commitments made to communities, including legacy issues, is a critical component in good corporate community relations.   The second part of the paper will identify some of the impacts and challenges of mining that need to be addressed in corporate community negotiations and consultation. Respect for indigenous people's rights and their right to give or withhold consent for a project to proceed is increasingly evident, as is the growing global expectations with regard to revenue transparency. As such, key challenges include: grievance mechanisms; free prior and informed consent; transparency and accountability; the gender impact of mining; resettlement, compensation and benefit sharing; and security issues.   Finally, the paper will provide practical guidance to companies on how to establish effective corporate community relationships. It will include examples, such as human rights impact assessments, gender impact assessments, and establishing local level grievance procedures. The paper will include an Oxfam Australia case study of a dialogue mechanism at Tintaya copper mine in Peru.

Jun 1, 2010

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By H Yuan, H Tian, Y Zhang, Z Wang, C Wang

Submerged arc welding (SAW) is one of the significant metal-joining processes for manufacturing marine vessels, steel pipes, and offshore structures with high deposition rate and engineering reliability. Welding flux serves several essential functions, including atmospheric shielding, arc stabilisation, bead morphology control and weld metal (WM) refinement. Therefore, from a thermodynamic point of view, the focus for flux design and WM compositional/microstructural modification has been placed to elucidating the transfer pathways and mechanisms of major alloying elements, such as Si, Mn, Ti and O during welding. To this end, a thermodynamic model has been established to predict alloying element contents in the WM. Such functions are enabled by the physicochemical properties of the fluxes, which are inherently rooted in the nature of the fluxes. A unique yet systematical investigation, including physicochemical property changes and structural evolution behaviours, has been conducted over the wide range of fluxes applied to actual welding of EH36 shipbuilding steels. Combined with spectroscopic methods, structural behaviours of network formers such as SiO2, Al2O3 and TiO2 and network modifiers such as MgO, MnO and CaO have been illustrated. Viscosity and ionic conductivity have been found to be positively associated with the degree of polymerisation.

Aug 21, 2024

By P J. Marsh, P J. Bartsch, N J. Semler

Iron Road Limited is currently studying the feasibility of producing 20 Mt/a of high-grade (67 per cent Fe) magnetite concentrate from a 2.6 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate has been tested at a relatively coarse grind size of -106 ¦m. The preliminary flow sheet has been confirmed based on initial mine plans and comprehensive metallurgical testing across the range of mineralisation. Extensive Davis tube testing to predict magnetite recoveries has been conducted over the resource, however this was completed at settings different to the optimised settings developed in the metallurgical test work program.This paper outlines the development of an ore treatment simulation in SysCAD which utilises the mine production plan, the Davis tube test data from the resource, data from metallurgical test work and process design criteria to predict magnetite concentrate deliveries. Mineralogical data, including QEMScan results and metallurgical assessments, were a fundamental basis of the process models which enable predictions of concentrate yield and quality. Power and water requirements are also calculated within the model. SysCAD dynamic simulation has been used to assist with the design of the process plant and downstream infrastructure. The simulation has been set-up to allow iterative integration and optimisation of the mine plan when it becomes available.CITATION:Semler, N J, Marsh, P J and Bartsch, P J, 2013. Iron RoadÆs prediction of magnetite concentrate production from the Central Eyre Iron Project, in Proceedings Iron Ore 2013 , pp 539-546 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N Weerasekara, M Bird, M Yahyaei, M M. Hilden, M S. Powell, J Franke, P Toor

The combination of new tools with a more rigorous approach to understanding the interaction of mill liners with overall mill performance and economics, forms the basis of an integrated approach to liner management. Based on accurate liner wear measurements, some (limited) physical mill inspections and surveys, accurate calibration of the mill load and analysis of process data, a whole new approach to liner selection, relining intervals and mill control is proposed. Collection and analysis of this information in operating mills illustrates the mill performance improvement which can be attained through this careful measurement and modelling approach.A more holistic approach to liner management is proposed, including a broadening of the current work to cover the potential benefits of improved relining technologies and predictive liner wear modelling. CITATION:Powell, M S, Hilden, M M, Weerasekara, N, Yahyaei, M, Toor, P, Franke, J and Bird, M, 2012. A more holistic view of mill liner management, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 95-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A Halim

"There is still debate about who should ultimately be responsible for the ventilation system in anunderground mine. The Queensland Coal Mining Safety and Health Regulation 2001, states that adedicated ventilation offi cer is the person, while Western Australian Mines Safety and InspectionRegulation 1995 states that it is the mine manager who is responsible; the ventilation offi cer actsas the managerÆs principal ventilation advisor. This paper outlines a comparison between bothapproaches."

Jun 1, 2012

By M P. Sandy, V Louchnikov, V Eremenko, M Orunesu, O Watson

"Surface support is a key component of most ground support systems which are applied as a means of reducing the risk of rockfall occurrence and maintaining serviceability of mine development. Surface support has two primary functions: distributing the applied load throughout the system by providing connection between rock bolts retaining smaller rocks that unravel between rock bolts.Confinement is also provided to the rock mass, which may increase its capacity to resist further degradation or loosening.Surface support has been routinely installed in most underground mines around the world for many years, yet the operators are still not always certain which type is best suited for deformable ground conditions. A number of factors need to be taken into consideration prior to selecting the type of surface support liner, such as its capacity, availability, practicality of installation, manual handling and loading conditions (static or dynamic) to ensure the system’s optimal performance in terms of safety and costs.This paper presents an overview of the surface support types currently used in underground mines in Australia. Shotcrete, weld mesh, high-tensile chainlink mesh, reinforced weld mesh and high energy absorption (HEA) mesh are discussed. A detailed description of each system is provided in terms of capacity, energy absorption, installation cycle and costs. The cost of each system has been normalised to the units of energy absorbed. The information presented in this paper can be used by underground operators as a reference guide when deciding on suitable surface support type for deformable ground conditions.CITATION:Louchnikov, V, Sandy, M P, Watson, O, Orunesu, M and Eremenko, V, 2014. An overview of surface rock support for deformable ground conditions, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 57–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15 000 tpa magnesium alloy production facility in Nanjing, China. Site construction commenced in February 2005, with installation of all major components completed by the end of October 2005. Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005. Since that time, ramp-up to the name plate capacity has been undertaken. This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By K Williams, A Lavrinec, V Gurung, D Ilic

The moisture content of iron ore during handling can range from the dust extinction moisture at the point of arrival at the port to the transportable moisture limit at the point of loading ships for maritime transport. Moisture content and ore composition, specifically fines content, have a large influence on ore flowability. Typically, elevated moisture can result in bottlenecks, downtime and lost productivity due to build-up, conveyor carry-back and blockages, increasing maintenance costs. On the other hand, low moisture can result in increased dust emissions influencing the environmental footprint and product losses. Managing the use of water across the supply chain is therefore critical for service life of equipment, productivity, but also has environmental and social impacts, affecting the social license to operate. Previously, experiments have shown that oscillations induced in iron ore during handling and transport can result in movement of moisture through the ore. This kind of moisture migration depends on the nature of these oscillations, such as the undulation of idlers during conveying, the inherent ore properties and the initial moisture content. Moisture has been observed to move either upwards and/or towards the bottom of the burden. These effects can be exploited to remove excess water from the ore influencing handleability and operation, however, the actual mechanisms of moisture migration are currently poorly understood. The study presented herein involves the use of simulation to examine moisture and ore interactions. Simulations using discrete element method (DEM) and coupled with smoothed particle hydrodynamics (SPH) are implemented to investigate the behaviour of moisture in wet ore in the presence of oscillation. This is conducted at a fundamental level first using glass beads and water which is then compared to iron ore at high moisture content. The results of the modelling are discussed in view of experiments conducted.

Sep 18, 2023