Search Documents

By Y Durkheim, P Saunier, L Ameglio

"In the last decade Afitex developed the Draintube™ geocomposite, which provides simultaneous drainage and waterproofing functions. This new type of drain tubes planar geocomposites (DTPG) differs from other geocomposites as the drainage core is composed of multiple corrugated and perforated pipes instead of biaxial or triaxial nets. It is furthermore associated with needle-punch stitched layers of non-woven geotextiles, which act either as capillary mediums or as filters.In this paper, the structure of the Draintube™ drainage composite is presented along with its key properties and the drainage mechanism associated with its particular structure.The relevance of this kind of structure is then reviewed based on past and current laboratory bench evaluations and field installations for mining applications such as the covering of acid rock drainage (ARD) tailings for the Central Manitoba Mine (Canada) site-rehabilitation; and as a pregnant solution collection layer in heap leach pads.Some of the demonstrated critical advantages of Draintube™ in the mining industry are as follows: reduction of the thickness, hence lower volume of granular drain layers improvement of fluid and gas collection and reduction of the hydraulic load reduction of secondary collector network mechanical protection of the sealing membrane fast and economical installation of interlifts stability under extreme conditions (compression, temperature, pH) increased stability of entire covering system and reinforcement of protection of dykes filtration of the covered material customised drainage positive connection of the geocomposite to collector pipes enable leaks detection (using a conductive textile layer) with an electrical test.CITATION:Saunier, P, Ameglio, L and Durkheim, Y, 2015. Tubular drainage and lining geocomposite for mine tailings and heap leach pads, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By Lock PR

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 kin north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bed's life cycle of construction and placement and mucking of ore from the marker bed.

Jan 1, 1998

By L Gobbo

X-ray diffraction (XRD) provides useful information about the composition of an ore sample in terms of quantification of crystalline phases and amorphous content. The use of new, fast detection systems implemented in CubiX FAST industrial diffractometers creates the opportunity to use this technique in exploration and modern process control. Besides the chemical composition of iron ores, their phase composition is also an important factor for exploration, quality control and processing. In the analysis of iron ore, XRD can identify the phases containing iron, such as haematite Fe2O3, magnetite Fe3O4, and goethite FeO(OH), and any other mineral phases present, especially silicas. Quantitative analysis is possible by various classical methods such as straight line or polynomial calibration with standards, but modern quantification analysis techniques such as Rietveld analysis or full pattern autoscale analysis are attractive alternatives, as they do not require any standards. These methods offer impressive accuracy and speed of analysis. Another analysis technique offering great benefit to ore exploration and process control is cluster analysis. This technique greatly simplifies the analysis of a large amount of data, eg from drill core samplings, and automatically sorts closely related scans of an experiment into separate clusters and marks the most representative scan of each cluster as well as outlying patterns. This can facilitate multi-dimensional compositional mapping of ore deposits, identifying regions of favourable mineral composition and allows fast and reliable tracking of the process. It is the most economic procedure to have automatic data evaluation without involving any dedicated personnel in the process. Details of the techniques used, sample optimisation methodologies, results, data precision and limitations will be discussed. The approaches have enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron ore materials in an industrial environment.

Jan 1, 2009

By A Fowler

The unpredictability of the location, grade and width of narrow-vein deposits presents difficulties for mine geologists and engineers attempting to estimate, schedule, forecast and mine their deposit profitably. This unpredictability stems not only from the grade distribution within a vein, but also the irregularity of vein geometry in three-dimensional (3D) space. Traditional deterministic methods of modelling vein geometry do not account for the inherent variability of the veins, resulting in significant errors when using limited drill hole information. This paper presents a probabilistic method of modelling narrow-vein deposits using sequential gaussian simulation (SGS), which can quantify this variability and improve production forecasts. Vein geometry, thickness and grade are simulated to provide a number of different equi-probable realisations that each honour the drill hole and face sample input statistics. An example is presented from the Augusta narrow-vein Au-Sb mine in central Victoria, where the simulation results are validated against the input data and survey pick-ups of the veins along ore drives.

Aug 22, 2011

By J Loeb, R Ramanathan, H Ingham, P Cameron

Most mining operations, including iron ore, maintain a focus on continuous improvement and asset optimisation in their operations. As all the unit operations in the Mine-to-Mill value chain are interdependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and impact of changes to the process. In this paper, we discuss some of the critical attributes in the Mine-to-Mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve Mine-to-Mill processes. Mining operations are planned and executed based on designs and models to achieve the operation's objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Therefore, measurement of the key attributes establishes the baseline for Mine-to-Mill (or Pit to Plant) performance, which is necessary to understand the impact of any proposed improvements to the process design and execution and monitor the outcomes on an ongoing basis sustain the improvements that have been implemented. This paper focuses on two types of measurement – blast movement and particle size of materials through the Mine-to-Mill process. Several innovative technologies and control loops are readily available to measure these attributes and assist operations to improve productivity and mine site profits. The size of the tangible benefits, which can flow from measuring and optimising fragmentation and blast movement, provide a remarkable return on the investment. Realising these benefits needs a focus outside conventional operation silos as a successful Mine-to-Mill project requires a multidiscipline approach across all the silos in the value chain. Required technologies are available; adding the necessary ingredients of communication and co-operation by all concerned across the silos will ensure the benefits are realised.

Nov 8, 2021

By J Lea, D C. Kettlewell

The Carina iron ore deposit lies 105 km northeast of Southern Cross, WA. The area designated the Yilgarn Iron Ore Project (YIOP) is comprised of five prospects along an east-southeast trending greenstone belt that extends from the Helena-Aurora Ranges in the northwest to the Yendilberrin Hills in the southeast, over a strike length of approximately 40 km. The YIOP project encompasses the previously identified iron deposits of Bungalbin, Bungalbin East and Mt Walton. The Carina deposit was discovered by Polaris Metals NL in May 2007. The Carina deposit is located within and parallel to the structurally complex northwest trending Mount Dimer shear zone. The volcanosedimentary Archaean-aged greenstone sequence consists of ultramafic and mafic lavas and flows with interbedded sediments dominated by chert and banded iron formation (BIF). Supergene enrichment processes formed a goethite orebody replacement of BIF sequences within a doubly plunging synclinal fold structure. Mineralised outcrops dominated by goethite form a low ridge 1500 m long, up to 90 m wide and drilled to over 200 m in depth. In the vicinity of the Carina deposit, iron occurrences have been identified over at least a 12 km strike length and the exploration potential of the area is identified as 30 - 40 Mt. Polaris Metals began exploration in the area in 2006. Target generation in the area used existing state geological survey maps and regional magnetic survey data to focus on BIF occurrences associated with major structures. Early field investigations resulted in the identification of a large outcrop of predominantly goethite mineralisation at Carina. Detailed geological and structural mapping was completed, followed by close-spaced reverse circulation and diamond drilling. The mineralisation is predominantly goethite with specular and coarse platy haematite localised along structures that cut the goethite mineralisation. Mineralised zones are moderately vuggy and larger cavities occur in proximity to fault zones that transect the orebody. A capping by a thin veneer up to 9 m thick of canga or ferricrete occurs in places. By December 2008, 178 reverse circulation and 11 diamond drill holes (seven surface holes, four tails) were completed. The current JORC-compliant resource estimate is based on assays from 72 RC drill holes and using a 55 per cent Fe cut-off stands as an Inferred Resource of 27.9 Mt at 58.6 per cent Fe, 1.3 per cent Al2O3, 3.7 per cent SiO2, 0.09 per cent P, and 10.1 per cent LOI. Assaying has recently been completed and will be incorporated into a new updated resource later in 2009.

Jan 1, 2009

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J V. Mehrabani, A R. Sayadi

Adequate estimation of equipment costs is a key factor in a feasibility study and in evaluation of design alternatives for mining and mineral processing projects. Inaccurate early cost estimation could lead to the elimination of investment benefits. However, this estimation is complex and time consuming because of data accessibility problems and consequently access to a rapid, up-to-date and accurate tool is desirable for carrying out cost estimations.This paper describes the development of models for estimating capital and operating costs for a jaw crusher, which is used as the primary crusher for a wide variety of mineral beneficiation plants, applying single and multivariate regression analyses, together with the design of experiment approach, based on principal component analysis. Explanatory variables include gape size, length of feed opening and power as numeric (quantitative) variables and toggle type (single or double) and the existence of extra heavy duty construction as categorical (qualitative) variables. The performance of each model has been investigated and comparing the estimated R-squared (R2) of each model, the best was selected and its validity examined. The cost models include the capital and operating costs along with the operating cost components. The results indicate that the suggested best cost model is sufficiently accurate for use in feasibility studies.

Sep 26, 2011

The Kidston breccia pipe is situated approximately 280 km west northwest of Townsville, north Queensland. It is currently Australia's largest gold producer with production varying between 8,000 and 16,000 tonnes of ore per day. Current reserves are estimated at 36.2 million tonnes averaging 1.74 C/t Au and 2.21 g/t Ag. Alluvial gold in the gullies surrounding the deposit was first discovered in the 1880's and between 1907 and 1948 small scale open cut and underground mining was undertaken. Advances in extractive metallurgy and an increase in the gold price were major factors influencing the recent exploration and development of large scale mining of the deposit by Placer Pacific and Kidston Gold Mines. The breccia pipe is trapezoid in shape with surface dimensions of 1100 m by 900 m. Clasts show only limited evidence of mixing during brecciation, with the pre-breccia stratigraphy still discernible on the basis of clast types. This lack of mixing together with the intimate association with intrusive activity, suggests that the brecia formed by collapse, probably associated with the escape of a large volume of irothermal fluid from a crystallising hatholith. Mineralisation and alteration are also sratially and temporally associated with rhyolite emplacement and brecciation. Pre-breccia mineralisation consists of laminated stockwork quartz veins associated with muscovite, quartz and orthoclase-epidote alteration. Stockwork veins contain either anomalous molybdenite or gold. Uneconomic early stage post-breccia mineralisation and alteration consists of cavity infill quartz-epidote and calcite associated with potassic and propylitic alteration respectively. Economic late stage post-breccia cavity infill and sheeted veining consists of quartz-carbonate-sulphide infill associated with phyllic alteration. The grade of gold mineralisation generally decreases downwards in the system with an increase in the amount of pyrrhotite relative to pyrite. Pre-breccia stockwork quartz veins mineralisation is genetically related to the

Jan 1, 1987

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Willis, A Shanahan, C Jacobs, T Luxner

The application of tunnel boring machines (TBM) for reef mining is a unique practice with benefits over current mining methods given the right geology and geometry of the orebody. The Stillwater Mining Company (SMC) of Nye, Montana, USA operates two mines for obtaining platinum metals. The operation is currently using a 5.5 m diameter open-type machine for further mine development, as well as another TBM that they own.The latest 7.1 km bored tunnel, known as the Blitz Tunnel, will be routed parallel to the ore deposit in igneous mafic intrusive rock, and will be used for the life of the mine operation. It will be used to map the ore deposit, and provide a rail haulage route.Detecting the reef in relation to the TBM requires careful analysis. Diamond core drilling occurs ahead, above, and alongside the machine at every 150 m. The core is drilled, logged, and interpreted on the spot, concurrent with boring. Based on the data, the TBM is readjusted so that it stays on the correct bore path.This paper will highlight the application and benefits of TBM usage for reef mining, with detailed descriptions from the mine site.CITATION:Willis, D, Jacobs, C, Luxner, T and Shanahan, A, 2014. Tunnel boring machine usage speeds up development at Stillwater Mine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 683–690 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

By B L. Dickson, E, M F. Lee, P A. Mikula

Computational techniques are needed to assist in the analysis and interpretation of the increasing amounts of geoscientific and mining related data and information that are routinely gathered at mine sites. New interpretation methods are needed to provide an integrated approach so as to establish relationships (cause and effect) or to be predictive about possible outcomes based on acquired data. Traditional multivariate statistical methods are often confused by variable relationships that are non-linear, data distributions that are non-normal, and by the data themselves that may contain missing values, text and both continuous and discontinuous numeric values. Modern data mining methods are available to understand the relationships within and between diverse data sets, and identify relationships or trends associated with processes, measurements and mine design parameters in mines. The self-organizing map (SOM) is a data mining approach with the advantage that all input data samples are represented as vectors in a data-space defined by the observations (variables). The SOM procedure is an exploratory analysis tool that highlights patterns and relationships. Results are internally derived, in an unsupervised fashion based on measures of vector similarity. Our SOM outputs are highly visual, which assists in understanding and illustrating the dataÆs structure and internal relationships. Two studies are presented. The first uses SOM to investigate the relationships between a range of measured and derived rock property parameters and their observed behaviours during mining. Our aim was to determine whether a SOM analysis would allow a better understanding of observed and predicted rock behaviours from their rock properties. The SOM analysis showed that there were indeed relationships between æbrittleÆ, æsugaryÆ, æslabbyÆ and æsqueezingÆ rock behaviours and a number of the input parameters. The computed SOM æstructureÆ was then used to assess the likely behaviour of unknown samples by assigning them into behavioural fields based on their measured and derived geotechnical responses. The second study was aimed at assessing whether a SOM analysis of microseismic data at the Kalgoorlie Consolidated Gold MineÆs (KCGM) Mt Charlotte mine can contribute towards understanding and potentially forecasting/minimising seismicity at the mine-design stage. The database comprised 40 sample æclustersÆ of microseismic parameters from the MS-RAP software package, which were derived from 2500 individual seismic events. The SOM analysis showed that some of the initial mining conditions are related to the seismic parameters. In each of the studies, the SOM procedures assisted in understanding the data and provided new insights. Because of its æordered vector quantisationÆ foundation, the SOM procedure is a substantial improvement over traditional statistical methods in three main areas:its ability to analyse data from disparate sources, including different data types; its ability to analyse sparse data sets with missing values; and its ability to analyse and visualise non-linear relationships within a data set.

Jan 1, 2006

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Bartle

In many operations the use of less electrochemically reactive grinding media in the first grinding stage (for example, rod milling and high aspect ratio SAG milling) is rarely considered. Therefore, in reality a plant may inadvertently be using a 'mixed' media charge. That is, whilst employing inert grinding media during secondary grinding, electrochemically active forged steel grinding media may be used in the primary grinding stage. This paper discusses the impact of such a circuit on the pulp chemistry and flotation response of a refractory gold ore. The Wiluna concentrator has two grinding circuits operating in parallel. Line 1 operates a single ball mill in closed circuit with cyclones, and utilises high chrome grinding media, while the second circuit (Line 2) consists of a rod mill (with forged steel rods) in series with a ball mill, which also utilises high chrome grinding media. The cyclone overflows from both circuits are combined to feed a sulfide flotation circuit. Pulp chemistry surveys were completed around both grinding circuits, and laboratory flotation tests were conducted on the cyclone overflows. The results demonstrate clearly that the rod mill/ball mill circuit operated at significantly lower Eh and dissolved oxygen values, while the percentage EDTA extractable iron was considerably higher, when compared to the single stage ball milling circuit. These variations in pulp chemistry had a marked negative impact on the laboratory rougher flotation response, and suggests that plant performance may be affected.

Jan 1, 2008