Search Documents

By T Purvis, J Calverd, A-K Greve

The Ernest Henry Mining (EHM) underground mine is situated adjacent to the Great Artesian Basin in North Queensland and within a fracture zone. Underground development commenced in February 2008 and has extended to approximately 1000 vertical metres below the surface.Groundwater has been encountered in numerous locations throughout the mine, predominantly on the eastern side of the orebody and often related to fault structures. Most of the groundwater encountered has been managed with conventional pumping systems; however, on occasions large water inflows have been encountered, which have had a significant impact on the planned development of the mine. Some of the intersections encountered had the potential to compromise the mine from a combination of high temperature (over 45°C), high pressure (3500 kPa) and high flows (50–100 L/s).This paper describes three case studies where significant water inflows were encountered and then controlled by the injection of cementitious grout into the rock mass. The case studies are the 1650 mid-shaft heading, the 1325 shaft access decline and the 1625 to 1475 fresh air rise (FAR) raise bore. Each case study includes a brief description of the event that occurred and the grouting equipment and techniques developed to enable mining to continue.The paper also describes the development of a hydrogeological map of the mine, the probe-hole regime used for high-risk headings and the required processes and systems to inject both cementitious grouts and polyurethane resin into the rock mass.CITATION:Purvis, T, Calverd, J and Greve, A-K, 2014. Management of high-pressure groundwater in underground development at Ernest Henry Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 217–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Marshall B, Gee R. D

Geological data processing by machine enables'an increased rate of coverage, better supervision and control of field programmes, increased effectiveness of field operators, and vastly improved access to old and new field data. Even a system of restricted felxibility enables a mapping programme to be organ- ized and conducted independent of personnel changes, whilst elimination of much compilation time increases the rate of cover- age such that it relates to mode of transport and geological complexity rather than to personality factors. A machine is useful only if applied to tasks suited to its capabilities, and must be aimed at those types of mapping in which a limited number of attributes adequately define the problem, and the data is of a form suited to coding and is normally collected in sufficient abundance to make compilation wearisome. Machine systems are therefore unsuited to most types of lithological mapping and to most types of exploration in new areas, but have proved useful in many branched of cartographic geophysics (e.g. gravity and magnetics), and in cartographic Geochemistry.

Jan 1, 1969

The operations management system at Olympic Dam has evolved over a two-year period to the state described in this paper. This evolution has been driven largely by the requirements of the recent expansion of the Olympic Dam operation from three to nine million tonnes of ore per year. Such a change process demands an holistic approach to mine management and several techniques have been employed including XPAC, Mine Works Planner as well as a basic philosophy of æjust-in-timeÆ completion. The philosophies, software and tracking mechanisms for managing a large tonnage operation are described, outlining a fully integrated scheduling system from shift to shift detailed activity planning to a 20 year production plan. Moreover, the vision of production exceeding the current limit of nine million tonnes means that there are to be further developments to this state-of-the-art system in use at the Olympic Dam mine.

Jan 1, 2000

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

By Lee RJ

A significant basemetal province is recognised in the southern part of the Bonaparte Basin, Western Australia. Epigenetic stratabound carbonate hosted Pb-Ag-Zn mineral- isation occurs in dolomites of Tournasian age within a marginal marine transgressive carbonate and fine grained clastic sequence, spatially overlying the lagoonal facies of a Late Devonian reef complex. The deposits comprise coarse grained sulphide mineralisation characterised by high Pb:Zn ratios (10:1) and high silver (50 g/t) content. They occur at shallow depth, are flat to moderately dipping, and form a discontinuous mineralised trend at the margin of the Sorby Platform, which flanks a Precambrian basement high. Host rocks are predominantly sedimentary breccias and dolomitised footwall carbonates associated with a significant local unconformity transgressed by a siltstone cap rock sequence. The deposits are structurally related to synsedimentary growth faults, local basement highs and tensional en-echelon breccia systems. Fluid inclusion studies have concluded that mineralisation was deposited from a low temperature (85¦C-115¦C) saline ore forming solution. Lead isotope work reveals a Precambrian genetic source of the lead. Locally remnant textures after sulphates are recognised within the host sequence together with common bitumen and oil shows. Reduction of sulphate to H2S was possibly facilitated by either bacteria. activity, or by residual hydrocarbons which acted as a reducing agent. An alternative source of H2S may have been afforded by the thermal degradation of hydrocarbons. A 'mixing' genetic model is proposed for the mineralisation, which conceives the expulsion of metal enriched basinal brines followed by their precipitation as sulphides after mixing with locally derived reduced sulphur solutions at relatively shallow depths in their structural/stratigraphic sites of ore deposition.

Jan 1, 1986

By Jaczkowski B

The lower orebody (LOB) at Chingola Divi- sion of Nchanga Consolidated Copper Mines Limited (NCCM) accounts for approximately 30 per cent of the total copper production for the company. The uniformity of the geology of the orebody lends itself readily to a computer based ore reserve calculation and accounting system. The mining units are physically defined such that a hierarchical type of com- puter file organisation can reflect the existing physical interdependencies. In 1972, a project team consisting of one representative from each of the mine planning, operational research, and computer services departments was formed to investigate and to define the technical mining requirements of the dynamic ore reserve system (DORS). The system was finally implemented in 1975ò

Jan 1, 1977

By Thomas G. A

THE irregularity of the Mount Morgan (Queensland) ore body presents problems other than those only of mining. For irregularity of outline is coupled with irregularity of grade, and the ore varies so rapidly from profitable to non-profitable, and fromhighly siliceous to highly pyritic, that the task of estimating quantities and values of ore reserves is manifestly rendered a difficult one, while the actual disposal of the broken ore demands constant supervision.Four classes of ore are handled. The oxidized ore, cheaply mined and cheaply treated, is obtained by quarrying from the top of the mountain. Below the 315-ft. mine level (measured from the original summit) sulphide ore comes in, and this is divided into siliceous sulphide ore (too siliceous for economic smelting), sulphide ore suitable for smelting, and ore too poor either to be smelted or to be treated by wet process with the siliceous ore. It is with these three latter descriptions of ore that this paper principally deals.Although the output from many stopes in the mine may usually be presumed beforehand to be either smelting or wet-treatment ore, yet it is never safe to take this for granted, and constant assaying is necessary. At the same time the ore merges from one class into...

Jan 1, 1911

This paper reviews some of the factors thought to control the formation of supergene gold in the Pacific and its Rim. Discussion of these should lead to reassessment of the economic potential of many areas. In several parts of the world many gold-bearing veins display rich gold values only in the oxidized zone, whereas beneath the present (or ancient) watertable the unaltered vein commonly holds only sub-economic refractory low grade sulphides or arsenides. In the Eastern Highlands of Australia some of the most spectacular concentrations of - gold have been found at shallow depths. For example, Harper (1918) describes the Canton mine in New South Wales which was stoped over a length of 180 metres from the 45 metre level to the surface. The reef yielded gold at 300 g/t in the upper levels, but became gradually poorer at depth. Present geologists of N.S.W. Geol. Survey, G.R. Mcllveen and B.P.J. Stevens, believe that many similar Australian enrichments were formed between the surface and its ancient water table level during the extended period of weathering in the Eocene or pre-Eocene. They concede, however, that further supergene movement of gold may have occurred since the early Tertiary. Large quantities of Mesozoic supergene gold of extreme fineness (Au 99.7%, Cu +òFe 0.3%; Leibius 1885) was found at Mt. Morgan near the Tropic of Capricorn in Queensland. Lower Jurassic sediments cover part of the gossan in a small depression caused by oxidation and collapse of the Main Pipe, thus showing that the supergene gold is pre-Lower Jurassic (Cornelius, 1968). Because the Lower Jurassic landscape around Mt. Morgan was mature with a surface slope of less than 10 (Playford and Cornelius, 1967), erosion would have been very slow. Moreover, once all sulphides had been removed from the ore body the Lower Jurassic environment would have reverted from highly acid to alkaline as it is at present. Accordingly, gold, goethite and 1. Dept. of Geology & Mineralogy, University of Queensland, St. Lucia, Australia,

Jan 1, 1987

By den Drijver J

Worldwide, hard coal mining is being carried out at ever increasing depth, and has, therefore, to cope with correspondingly increasing methane emissions. About seven per cent of global methane emissions are caused by coal mining. Beside carbon dioxide, chloro-fluorocarbons (CFCs) and nitrogen oxides, methane is one of the most significant `greenhouse' gases. It is mainly through the release of such trace gases that the greenhouse effect is brought about. Reducing methane emissions is therefore an important problem to be solved by the coal mining industry. This paper begins by highlighting some of the fundamental principles of methane in hard coal mining. The methane problem in German hard coal mining and the industry's efforts to reduce methane emissions are presented. The future development in German hard coal mining is illustrated by an example which shows how large methane volumes can be managed, while still maintaining high outputs at increasing depth.

Jan 1, 1995

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

By P B. Hills

Almost a quarter of a century since Bridges (1993) documented techniques for the assessment of ground conditions in a seminal paper in the Proceedings Second International Mining Geology Conference, the necessary role of the geologist in recording geotechnical data on exploration properties and in mines remains. Typically, the geologist is the first professional on the exploration property. Of course, most exploration properties don’t become mines. However, when a property does start to come together and form a coherent mineral deposit and professionals from across the minerals industry spectrum, including specialist geotechnical engineers, become increasingly involved, it remains the geologist who has the most intimate knowledge of the deposit. By association, that knowledge extends to the character of the rock mass.Throughout the various phases of prefeasibility, feasibility, construction and production, culminating in the mature mine, the knowledge of the rock mass held by the geologists continues to grow. In the current era of minimising cost and optimising profit, meeting the requirements and expectations of stakeholders ranging from fellow employees to investors, industry and financial regulators and the broader public, in a social environment where occupational health and safety concerns are of uppermost concern in every endeavour, the value of the geologists’ observations cannot be understated. Mines nowadays employ more geotechnical engineers than they did in the early 1990s when Bridges (1993) wrote his paper. More funds are available for specific geotechnical investigations of exploration properties and mines; none-the-less, those programs remain limited in their extent and there is a wealth of additional data available for collection with the appropriate training, at little additional effort. Fundamentally it is all about the numbers. Any hole not geotechnically logged is a hole that will need to be drilled again if the data is required. Any face, surface or underground, not geotechnically mapped is one that may need to be mapped a second time. That doesn’t mean every hole or every face. However, it is the proposition of this paper that the opportunity for additional geotechnical data to be gathered during traditional geological investigations is an opportunity that cannot be ignored. Occupational health and safety requirements demand that the geotechnical risks associated with mining are appropriately managed. Mining regulations in most Australian and overseas jurisdictions requires the consideration of geotechnical risk through formalised management plans. The Joint Ore Reserves Committee (JORC) Code requires the consideration of modifying factors more than ever before. The benefit to be realised through improved geotechnical understanding by geologists on the ground leads to improved occupational health and safety, optimised reporting compliance, and improved financial and social outcomes for the exploration property and ultimately for the mine that follows.CITATION:Hills, P B, 2017. The necessary role of the geologist in geotechnical data gathering, in Proceedings Tenth International Mining Geology Conference 2017, pp 347–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P Vass, C Butler, J Condon, B Hooper

DeGrussa Copper Mine, resource status 10.2 Mt at 5.7 per cent Cu, 2.1 g/t Au (Sandfire Resources, 2013), commenced concentrate production through its 1.5 Mt/a conventional copper flotation processing plant in September 2012. Geometallurgical assessment during the feasibility study identified potential process-critical ore factors that required further investigation to determine potential impact on processing. Ore characterisation and metallurgical processing performance test work of ore types ensued and subsequently, the first quantitative DeGrussa geometallurgy model was born. Now one year into steady state production, the geometallurgical program has evolved significantly from its infancy and provides valuable insight into ore characterisation and behaviour in the processing plant. This paper details geometallurgical investigations undertaken at DeGrussa to date; from feasibility metallurgical test work through to geometallurgical modelling and management practices, as well as reconciliation between observations at feasibility study level and subsequent observations in production.CITATION:Condon, J, Butler, C, Hooper, B and Vass, P, 2013. DeGrussa Copper Mine, Western Australia - feasibility to first production: a case study in developing a working geometallurgy model from first principles, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Mayer TE

The Granites Goldfield is located 550 km northwest of Alice Springs. Mineralisation was discovered in 1900 and intermittently worked along nine km of strike until the early 1950's, yielding a recorded production of 470 kg of gold. The geological environ- ment, pre-existing exploration drilling results, and an optimistic view on gold, prompted acquisition of the property by North Flinders Mines Limited in 1975. An agreement was signed with the Central Land Council in August 1983 and drilling commenced in the same month. In the past, gold was won from alluvial deposits, rich quartz veins and lower grade, disseminated stratabound mineralisation. The last is contained within a distinctive unit in the Mt. Charles Beds, of the Early Proterozoic Tanami Complex. This informally named "Host Unit" is a metamorphosed, chemical- pelitic sediment. The schist contains variable proportions of amphibole, quartz, garnet, clinopyroxene, carbonate and sulphide, inter- calated with recrystallised chert beds. Free gold occurs in several mineralised horizons within the Host Unit, generally conformably distributed within lithologic bands or at lithologic contacts. The Host Unit occurs within a sequence of metamorphosed pelitic sediments and intermediate volcanics. Although mostly confined to the Host Unit, stratabound gold mineralisation also exists in both Footwall and Hanging Wall Schists, usually within zones displaying certain Host Unit characteristics. The deposits may be loosely categorised as being of banded iron formation (bif) type, although some important differences are noted between them and classical bif type orebodies.

Jan 1, 1984

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

In todayÆs evolving and globalised world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to æengageÆ communities and measure the success of these engagements without a clear understanding of æhowÆ to do this. This move, away from compliance, develops more of a focus on sustainability and æcommunityÆ social responsibility rather than corporate social responsibility. This shift leads to the development of world-class projects that provide sustainable development for people, reduce the incidence of costly delays, and promote good global citizenship for companies. The process of æengagingÆ communities in mining project design and development leads to sustainable development, a stronger license to operate, and a reduction in social and political risk. To create this mutually beneficial relationship between communities and companies, communities must be æengagedÆ in the project development and risk assessment processes as early as possible, preferably during the exploration or the concept phases. How to create this æengagementÆ and manage this risk will be discussed.

Jan 1, 2007

IN this paper the author's intention is to convey a brief resume of the lead flotation treatment and lead flotation machines, which have replaced the May jigs and Wilfley tables at the plant of the North Broken Hill Ltd., and converted this mill into an all-flotation plant.Attention is directed to the fact that this drastic change from semi-gravity to all-flotation treatment, has been successfully accomplished without resorting to finer grinding than that previously in vogue for Wilfley table concentration, viz.: 10% to 16% plus 40-mesh I.M.M. screen.From the figures now available it is manifest that the scheme of all-flotation concentration-new as regards its successful application to Broken Hill ores is resulting in considerably higher-grade lead concentrates, and is substantially decreasing charges for labour, stores, and maintenance.The new treatment is far-reaching in its simplification of plant, as evidenced by the idle jigs and tables, and the results being obtained by North Broken Hill Ltd. may possibly influence metallurgical practice generally in Broken Hill.The outstanding features of the treatment are:(1) The coarseness, and high grade of lead concentrates obtainable.(2) The low time factor required for flotation.(3) The plant capacity, and the simplicity of its operation.(4) The low horse-power consumption.(5) The small cost for reagents used (not exceeding 3d. per ton of ore).

Jan 1, 1930

By G Clarke

Commissioning of the Cannington processing plant began in October 1997. The nameplate capacity (of 1.55 million tonnes of ore per annum) was achieved relatively quickly. Since then (like many mines) the operation has strived to increase throughput and improve valuable metal recoveries, to offset declining head grades and lift the value of the operation. The processing plant now has the capability of treating over 3.2 million tonnes of ore per annum and in financial year 2005/06 the combined concentrate production exceeded 600 000 wet tonnes, approximately 80 per cent above concentrate output in the first full year of operation (at the design feed rate). This improved performance was achieved by making changes and additions to each of the major unit processes û primary grinding, flotation, leaching, filtering and paste fill preparation. The changes have included: adding a fines flotation circuit, expanding the grinding circuit, adding a pebble crusher, switching from continuous to batch leaching, building paste conveyors and decommissioning the column flotation cleaning circuits. This paper reviews these changes, outlines the current operating practices and discusses the challenges or opportunities that remain.

Jan 1, 2007

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Lowell J. D

This paper is an outgrowth of a continuing compilation of the geology of Chilean ore deposits by Carlos Ruiz who was the author in 1965 of Geologia y Yacimientos Metaliferos de Chile which was the definitive compilation of the ore deposits of Chile. A new version was written by him in 1988, with the co-operation of Federico Peebles L, published in Geologia, Distribucion y Genesis de los Yacimientos Metaliferos Chilenos. Over the past eight years J David Lowell studied the geology of the Chilean mineral belts in connection with planning mineral exploration for copper and gold.

Jan 1, 1990