Search Documents

Early theories of coal formation are outlined, with special emphasis on the arguments for allochthony and autochthony. Various aspects of the nature, growth, and decay of the characteristic vegetation of the brown coal peat moors, their conversion into coal, the origin of banding, and the influence of tectonics are discussed.A description of the banding in Victorian brown coals is followed by a discussion of their vitrain, fusain, and natural carbonized coal; and concludes with the nature of the coal resin and the possibilities of its extraction.The nature and derivation of inorganic matter in brown coal, based on Lessing's classification, is described. Assimilation of mineral substances in specific plants with variations due to environmental factorsare illustrated by analyses of present day trees. Consideration is then given to possible sources of salt, marcasite, and quartz in brown coal.It is shown that part of the inherent and extraneous ash may have been removed during and after coal formation. The nature and abundance of the organically combined substances in brown coal emphasizes the anomalies that may arise from estimating the total inorganic matter from ash contents.After classifying deposits on external heating surfaces of boilers, theoretical and practical aspects of slag formation, alkali matrix deposits, and the effect of sulphur and chlorine are considered.Analyses of deposits in boilers burning Victorian brown coal are tabulated.Slagging at the Yallourn power station from sand in the Yallourn open cut, and difficulties with Yallourn North Extension coal at the Maryvale paper mills are described.Tests carried out on Morwell and Yallourn coals showed that with the former, impacted deposits formed on boiler heating surfaces, and left a high percentage of chlorides on probes. Morwell briquettescompared with Yallourn briquettes also reduced the running time of a semi-industrial boiler through deposits with sodium sulphate as...

Jan 1, 1962

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

By G R. Hancock, M J. Saynor, J B. C Lowry, T J. Coulthard

Landform evolution models (LEMs) can assess the effectiveness of landform designs applied to a rehabilitated landform by predicting where erosion may occur. Here, we compare erosion predictions produced by the CAESAR-Lisflood LEM with field observations from the rehabilitated Pit 1 landform of the Ranger uranium mine, based in the Northern Territory, Australia (Figure 1). The ability to predict long-term erosion at a catchment scale is important, as the final rehabilitated Ranger landform is required to physically isolate buried tailings material for at least 10 000 years. CAESAR-Lisflood has been extensively tested and calibrated using data collected from erosion plots (0.09 ha) on the Ranger trial landform (TLF) for multiple years (Lowry et al, 2020; Saynor, Lowry and Boyden, 2019). However, until recently, it was impossible to compare model predictions with field observations for areas larger than the TLF erosion plots. We can now compare model predictions of Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 116 gully development with field observations from the newly rehabilitated, 40 ha surface of Pit 1 over two contiguous one-year periods: 2020–2021 and 2021–2022. The aim of this study was to assess whether the CAESAR-Lisflood model can successfully predict gully erosion at a larger spatial scale.

Aug 2, 2023

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

MANPOWER RESOURCES The optimisation of human effort has been an ongoing and significant process in the coal industry since industrialisation as we know it began. The extent to which the changes sought have been achieved has, over the years, been in the main determined by the economic and political forces existing at that time and the determination and character of the individuals involved. The question of optimisation is therefore not new in our industry. Hopefully this presentation will demonstrate to the reader the effect of previous measures adopted by industry to optimise all facets of its operation and in particular that of the human Resource.

Jan 1, 1991

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

By G Forbes, D J. Bradshaw, G S. Heinrich, D

Traditionally, operators on mineral flotation plants have relied on visual inspection of the froth surface when making adjustments to process set-points. Machine vision systems are being developed to relate froth surface descriptors, which can be consistently measured in real time, to flotation performance. By investigating the impact of various selected operating variables on both froth surface characteristics and metallurgical performance it is possible to develop a management strategy for the control and optimisation of the process. This paper presents the results of testwork conducted at Kennecott copper mine which investigates the relationship between the froth colour and the concentrate grade and discusses the factors which affect the froth colour. This work shows that the main factors that influence the froth colour in this system are molybdenum, copper and iron concentrate grade, pulp and concentrate per cent solids and pulp iron grade.It goes on to develop models to predict the concentrate grade based on colour information and velocity and stability information. It also shows that the most accurate prediction is made with combined colour and stability information.

Jan 1, 2005

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By E Giles

Pike River Coal Limited (PRCL) is opening a new underground coal mine in the Paparoa Ranges north-east of Greymouth. To access the coal reserves, PRCL have had to build a 13 km access road through regrowth and virgin forest, and appointed McConnell Dowell Constructors Limited, with URS New Zealand Limited as their consulting engineers, to construct the final access link: a 2.3 km long, 5.5 m wide and 4.5 m high incline tunnel. This paper discusses the logistical issues of construction in an isolated pristine forest in mountain land and how they were addressed. It provides an overview of the 90 per cent complete tunnel and how challenging rock conditions have been mastered. It outlines briefly the remaining work which is construction of pit bottom workings where the mine infrastructure will be housed and construction of a 110 m deep, 4.0 m diameter, vertical ventilation shaft.

Jan 1, 2008

Portfolio management tends to separate the functions of Asset Allocation and Stock Selection, so the person responsible for reviewing an expert's report on a company would typically be choosing between companies rather than between a company and cash or bonds. How these choices are made depends on the investment time horizon, philosophy and style. Two styles, momentum investing and value investing are contrasted and the role of valuation methods within the framework of each style is evaluated. Finally, pricing is distinguished from valuation.

Jan 1, 1994

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By R Shaw, T T. Neidel, C Adams

Sampling equipment manufacturers endeavour to ensure that the mechanical equipment installed in sampling systems are designed and manufactured to adhere to the requirements of the International Organization for Standardization (ISO) or other standards relevant to the application. The mechanical parameters necessary to achieve these standards can be well controlled and requirements such as constant speed can be met through good mechanical design and engineering. However, when the equipment is installed and put into operation, the ISO compliance of the system is out of the hands of the equipment manufacturer and handed to the operator, who may be a generalist control system integrator.Making a sampling system perform according to standards, and being able to monitor and report on compliance require that the sampling system knowledge and the control integration is combined and applied in an integrated approach. Using a dedicated library of control routines developed for sampling can change a system from having compliant equipment to being a compliant system. The library has to include monitoring of relevant parameters and control and reporting on sampling parameters.CITATION:Neidel, T T, Adams, C and Shaw, R, 2014. Control and monitoring of International Organization for Standardization compliance for industrial sampling systems, in Proceedings Sampling 2014 , pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Fraser RJ

A Robbins Raise Drill Model 61R was used to provide one 7' diameter shaft 1050' deep in Clutha Development's exploratory mine at Blackwater in Central Queensland and two 7' diameter shafts 1450' deep at their South Clifton mine on the Illawarra Coast of New South Wales.

Jan 1, 1972

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

By Xueqiu H

Since the hypothesis of coal and methane outburst mechanisms based on elastic mechanics gives no consideration to time, it cannot give satisfactory explanation of the outburst occurrence and its development. A creep mathematical model of coal containing gas has been set up through creep tests and analysis under a condition of triaxial compression. Such a model can explain the phenomenon of coal and methane outbursts successfully. The tests proved that there is no essential difference between the rheological properties of prone outburst coal and non-prone outburst coal. Outburst can take place in any kind of coal if the rheological conditions of coal containing gas are met. The creep mathematical model provides a basis for establishing a comprehensive index of coal and methane outburst potential.

Jan 1, 1992

By Barro L

Very large reserves of gas are contained in coal. Because of the low permeability of the coal gas flow rates are very low. Fracturing of the coal can be achieved by use of the nitrogen - foam frac techniques described but the flow rates after fracturing are not sufficient to support economic development. Fracturing of the seams in the Bowen Basin was as predicted but in the Sydney Basin no trace of the fracture could be found when development proceeded past the fractured well. Testing of coal samples has provided some insight into parameters affecting desorption Rates.

Jan 1, 1982

By Toivanen R-M, Leinonen O, Pekkarinen H

This paper presents developments in designing an integrated mine control system at Kemi mine. The aim of this paper is to present the general structure of the system and to outline some features of the process control strategies. The results o

Jan 1, 1998

By Hayward N, Sutherland D, Wilkie G

A pilot plant study has been made of the liberation characteristics of a nickel ore under different milling conditions. A series of runs were made ranging from fully autogenous grinding to semi-autogenous grinding with a ball load of 8%. The mill products were sized and assayed then analysed by QEM4SEM. This enabled a full liberation analysis to be carried out to see whether the autogenous grinding leads to improved liberation by promoting selective breakage. Though it is frequently claimed that fully autogenous grinding yields superior liberation this could not be detected in the present study.

Jan 1, 1991

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997