Search Documents

By F Brenguier, R A. Lynch, G Olivier

The seismic velocities of intact rock are dependent on the applied stress. Unfortunately, the low susceptibility of seismic velocity to stress changes mean that changes in seismic velocity have to be measured extremely accurately to infer stress changes from them. Previously, it was thought that measurements of this accuracy could only be made with active sources or repeating earthquakes. In this paper, we show that the noise generated by mining activity can be used to construct virtual seismic signals with which we can measure changes in seismic velocity accurately enough to see the short- and long-term effects of a production blast on the surrounding medium. The time-dependent velocity variations achieved with this method show that the blast caused weakening of the rock mass for the rock within a radius of 200 m of the blast. The weakening is healed by confining stresses over a period of five days, after which permanent changes in the seismic velocity can be seen. The size and spatial distribution of the seismic velocity changes were compared to modelled changes in static volumetric stress, which supported the notion that seismic velocity changes can be used to measure the redistribution of stress after a blast. The results of this study indicate that this method can be a powerful tool to evaluate the evolution of stress in a mine at a relatively low cost as the data that it uses would normally be discarded.CITATION:Olivier, G, Lynch, R A and Brenguier, F, 2016. Measuring the redistribution of stresses resulting from new excavations with ambient seismic noise correlations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 873–878 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G K. N Subasinghe

"In the design and operation of mineral processing plants, knowledge of the variability of ore properties and that of the expected metallurgical performance within the orebody is of great importance in order to avoid both production constraints due to inadequate design and less than expected metallurgical performance during operation. Of the many properties that determine the performance of downstream separation processes, such as flotation, gravity separation and leaching etc the liberation characteristics are of primary importance.Current methods of evaluating liberation characteristics of ores such as the use of Mineral Liberation Analyzer (MLA) and QEMSCAN techniques are expensive and suffer from the drawback that these tests are performed on comminuted particles at a given grind size and/or samples of product streams. This problem could be overcome by developing predictive models of liberation that can predict the grade distribution of comminuted products at any grind size based on texture of the parent rock. This paper discusses a procedure that has been developed to predict liberation using information obtained from a sample of the parent rock such as drill core, based on Barbery’s liberation models. The required characteristic statistical functions have been evaluated from image analysis techniques using scanning electron microscope (SEM) images of the parent rock and narrowly sized comminuted particles. Such information can then be used in a predictive model to predict or explain the variability of metallurgical performance at various grind sizes used in future operating plants. The model will predict not only the valuable mineral liberation but also gangue liberation, which will be useful to those who are looking to remove liberated gangue from comminution circuits.CITATION:Subasinghe, G K N, and Dunne, R, 2016. Predictive Model of Mineral Liberation for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 347–350 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The detailed work done by Stillwell and Edwards on the occurrence of cobaltite and safilorite-Iollingite at the South Mine, followed by its presentation as a paper to the Institute, calls for, a few notes on its occurrence elsewhere in the Broken Hill field. No massive cobaltite similar to that in the South Mine veinlet is known except from the Consols Mine (as mentioned in the paper). Fine grained cobaltite has, however, been found in low-grade ore from the North Mine. Microscopic grains occur in a mineralized green feldspar pegmatite. The feldspar has been replaced in part by graphite, and the cobaltite occurs in association with the graphite. In its hardness, pinkish-white colour, and resistance to the standard etchingqeagents it is similar to the South Mine cobaltite; it is etched by acid permanganate solution. An interesting feature of this occurrence is the way in- which some of the minerals (notably galena) have forced apart the graphite lamellae in crystallizing, forming lenses enclosed by the curved cleavage surlaces 0;[ the graphite.StillwelI and Edwards cite a note by G. Smitht for the statement that "cobaltite has been recorded from the Australian Broken Hill Consols Lode in the vicinity of the rich silver deposits, though not in contact with them."Smith, however, is here referring to the oxidized zone. Elsewhere in the same article he states "... a deposit of cobaltite in a very much altered condition was found. This was impregnated with silver, and assayed as high as 3,000 ounces," Of the cobaltite in the unoxidized zone, Smith simply states that it became rarer with depth.Cobaltite has also been recognized by Mr. H. F. Whitworth, M.SC., Curator of the Mining Museum, Sydney, in specimens from Burt's Copper Mine eight miles south of Broken Hill.

Jan 1, 1944

A broad zone of intra-plate volcanism occurs for some 3000 km along the E. Australian coastal regions, extending from far northern Queensland southwards to Tasmania, westwards to western Victoria, and into southeastern South Australia. The age range, taken over the whole region, extends from Eocene to Holocene. Wellman & McDougall (1974) recognised the occurrence of three distinct types of volcanic occurrences: (a) Lava field provinces, dominantly basaltic and commonly strongly undersaturated, but of variable size. Large lava fields are especially exemplified by the younger provinces in northern Queensland (e.g. Nulla, McBride), and western Victoria. (b) Central volcano provinces, in which a reasonably well defined volcanic edifice is discernable. Such provinces are built of mildly undersaturated to saturated mafic lavas, but are also characterised by felsic volcanism (and often substantial mafic and felsic intrusive phases). Examples are the Springsure-Minerva Hills province, the Tweed and Focal Peak Shields (southeastern Queensland to northeastern N.S.W.), and the Nandewars, Warrumbungles, and Canobolas volcanic centres (N.S.W.). (c) A single leucitite province in N.S.W. Wellman and McDougall (1974) were able to show that the central volcano provinces exhibit a remarkably regular southward age migration pattern, the calculated migration rate being 66 + 5 mm yr , and these authors interpreted this in terms of the northward passage of the Australian plate across a fixed 'hotspot' within the upper mantle. The leucitite province also fits this migration pattern. The lava field provinces apparently exhibit more erratic regional age distribution patterns, but Sutherland (1981) has interpreted the data in terms of a multiple 'hotspot' model. It is noted, however, that the youngest areas of volcanism (Pleistocene 1. Department of Geology and Mineralogy, University of Queensland, St. Lucia, Brisbane, Queensland

Jan 1, 1987

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

By J Davidson

Ion exchange using strong base resins is a well established technology for the recovery and purification of uranium from sulfuric acid leach liquors. Production of uranium at the Beverley Mine in South Australia includes acidic in situ leaching, ion exchange and uranium precipitation. The salinity present in the groundwater results in a relatively high concentration of chloride in the leach liquor reporting to the ion exchange plant. The impact of chloride on the ion exchange process is discussed in this paper. The results presented show that an increased chloride concentration in the lixiviant solution feeding the ion exchange plant leads to increased uptake of chloride by the resin during the loading cycle. At the highest chloride concentration studied (7.5 g/L Cl) chloride took up to 60 per cent of the resin loading sites. The impact of the chloride can be summarised as follows: for a given uranium concentration in the lixiviant feed solution, the uranium loading decreased with increasing chloride concentration; a consequence of decreased uranium loading is an increase in the frequency of elution, with an associated increase in elution reagent costs; and for a given elution efficiency, the uranium concentration in the barrens is expected to increase with increasing chloride concentration.A few options were examined to counteract the impact of chloride: an increase in elution efficiency was targeted to reduce the amount of uranium returning to the loading circuit; increasing the pH improved uranium loading, but this was found to also increase iron extraction; and preliminary screening of alternative resins showed that the higher the theoretical ion exchange capacity of the strong base resin, the higher the uranium loading.Work is continuing on uranium recovery from saline leach liquors, specifically investigating the performance of alternative resins.

Jan 1, 2005

Titanium dioxide (TiG ) is produced 2 commercially by two methods generally referred to as the "sulfate" route and the "chloride" route. The SCM Corporation, in supplying 15% of the world's demand for TiO 2, uses both of these processes. Of the two processes the sulfate route is generally regarded as the older and more established technology. Worldwide the sulfate route accounts for some 70% of total Ti02 production. However, in the U.S.A. the chloride process accounts for 80% of production. The processes vary in chemistry and raw material requirements. In the "sulfate" process finely ground ilmenite or titanium slag is digested with sulfuric acid to produce a porous "cake" vrnich is extracted with water and recovered liquor. The solution is treated with scrap iron to reduce any ferric ions to the ferrous state which is then crystallised and removed as ferrous sulfate heptahydrate. The liquor is concentrated by evaporation and hydrolysed to form the insoluble hydroxide which is filtered and washed free of impurities. This is converted to the dioxide by calcination at 800 - 1000¦C and milled to break up any aggregates. The "chloride" process uses a higher quality feedstock of natural or synthetic rutile and/or high grade titania slag. The feedstock is mixed with ground high-purity coke and chlorinated at 950¦C in a fluidised bed. The resulting crude titanium tetrachloride is purified by distillation and chemical treatment. The purified titanium tetrachloride is burned with oxygen or oxygen enriched air to give titanium dioxide and chlorine, which is recovered and recycled to chlorination. Titanium dioxide pigment from both processing routes undergoes similar finishing techniques. It is subjected to further stages of wet and dry milling, then coated with layers of inorganic oxides in order to enhance its properties for specialist applications.

Jan 1, 1986

My closest personal connection with the problems of rehabilitation comes from two years spent on a project at Weipa. At the beginning I am fairly certain that the engineers did not understand the mental processes of the ecologist they were dealing with. I am absolutely certain that the ecologist did not understand the minds of the engineers. This form of the two cultures problem is the root of some of the matters that lie behind this lecture. It is possible to establish a stabilising cover of vegetation on virtually any land surface, short of a cliff. While the biologist knows this he also knows that the physical and chemical nature of a given acre of land combines with climate to define quite sharply just what plants can be grown there. In the case of land after mining the range of plants may be quite limited. The engineer, and his masters in the accounting section, seem (in my experience) to expect that rehabilitation can be carried on with equal speed and facility in any location. This belief commonly leads to a situation where rehabilitation is not considered until mining is well under way. True, the mine must be proved as an assured profit- earner before money can be justified for the non-productive (to the miner) expense of rehabilitation. But when the miner finally starts rehabilitation he does not always get a convincing and speedy result. Furthermore, the failure may not be easy to overcome. This is even more likely to be the sequence of events if the miner wants, or is obliged, to specify the exact type of vegetation to be produced, e. g. commercial forest, pasture,' or the original native vegetation.

Jan 1, 1971

Although the effects of sea level changes on ore concentration processes are to some extent obvious with certain deposits, e.g. beach placer deposits, they have been largely overlooked with others such as Mississippi Valley type lead-zinc deposits. It is contended that sea level variations may have more profound effects on a wide range of deposits than has previously been appreciated. These deposits include not only placer'and residual deposits but also stratiform copper deposits, Mississippi Valley type deposits, stratiform manganese deposits and Minette type iron deposits. Sea levels in paralic basins profoundly affect the influx of 'detrital sediment, and this has to be suppressed to allow for the accumulation of thick rich deposits of coal evaporites, phosphate or metalliferous sediment. Emergence can be associated with oxidized waters, erosion, and,solution of soluble rocks. Submergence can reverse the Eh trend and can lead to preservation of ores. Both realms of surficial sedimentary environments and subsurface diagenetic environments can be affected by changes in water pressure, gas pressure (pC02), Eh, pH, and temperature as sea levels fluctuate. Even relatively small sea level changes may have profound effects. For example, there is some evidence to suggest that when the level dropped below 100 metres about 10,000 years ago, the Red Sea became isolated by the sill at Bab el Mandeb in the south, and evaporated away to leave a series of shallow lakes. The Red Sea is 1 to 2 km deep. It was at times such as this that the well-known copper-zinc mineralization developed in the Red Sea trough. Changes in sea level also affect the stability field of gas hydrates which can yield large volumes of gas leading to mass movements on the sea floor (Warnke, 1986).

Jan 1, 1987

By P Gilroy

In recent technical investigations that were triggered from ore for rail shortfalls at Yandi, BHP Iron ore has identified a gap in resource knowledge relating to geo-metallurgical characteristics that predict materials handling performance and throughput. Within these investigations BHP has learnt that this lack of resource knowledge has translated to a lack of predictability associated with mine planning inputs which has resulted in poor compliance to plan and deviation management practices. A business value chain was developed in an attempt to identify the best possible solution to unlock this resource knowledge in the short, medium and long term planning horizons. A fast fail approach was taken with the implementation of hyperspectral blasthole analysis, which was chosen to deliver the best possible value driver for the asset. This report will detail the Yandi journey in expanding the hyperspectral and geo-metallurgical value chain, unlocking resource knowledge along the way. CITATION: Gilroy, P, 2018. Development of an empirical geo-metallurgical model that unlocks value of the mineral resources at Yandi Mine, in Proceedings Complex Orebodies Conference 2018, pp 85–87 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H J. J Boshoff

Mine closure planning integrated into life-of-mine (LOM) planning during the operational phase consists of many subcategories. One of these subcategories that needs to be fully integrated into the LOM planning is that of water management planning. Issues arise when mine water management infrastructure, which is required post-mine closure, is only considered closer to the end of LOM. Once the mine is closed monitoring is focused on water quality as an indicator of closure performance, hence inadequate upfront post-mining water management planning or integration into operations will result in environmental harm. The lack of considering post-mining water management is not uncommon in LOM planning. Poor mine site water management and planning are a wide reaching problem for the mining industry. Numerous active mines have been issued with environmental notices and penalties for contaminated water discharge; including issues with abandoned mines now being cared for by governments all over the world.Mitigating sources of water contamination caused by existing and closed mine sites that are leaching pollutants might be impractical, due to inaccessibility to the contaminants or final landform topography. The opportunity to consider and introduce post-closure required mine water management infrastructure is lost once the waste facilities are constructed. Mitigating contamination is made more problematic with mines located in remote areas, serviced by dedicated roads, water supply, electrical supply, etc. It is expected that these services will be decommissioned or drastically reduced, once closure is reached making remedial work much harder. Inadequate planning, to ensure access and easily maintainable water management infrastructure, could lead to erosion and contamination going unnoticed. There are numerous examples of poor mine water management practices in Africa, Asia, Australia, South and North America. In the United States more than 23 000 km of streams are affected by pollution sourced from some 50 000 abandoned or mature mine sites (DeGraff, 2007).CITATION:Boshoff, H J J, ?2014. Inadequate water management planning resulting in long-term closure liabilities, in Proceedings Life-of-Mine 2014 , pp 233–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Pearce, B Miles, V de San Miguel

Incorporating industry best practice waste rock management methods can be a relatively straight forward task when preparing management documentation, such as an acid and metalliferous drainage management plan (AMDMP). However, a key difficulty is the incorporation of industry best practice methods that are practical and non-compromising on their purpose from a scientific standpoint. The second key difficulty is the implementation of these practical methods as various operational groups/departments are typically relied upon to execute and take ownership of different tasks or procedures.One approach to overcoming these difficulties is to develop an AMD Operations Manual (AMDOM) that:•Incorporates, where practicable and without compromising scientific merit, existing processes that those groups/departments ultimately responsible for the execution of the management action are familiar with; and•Provides standalone, simplistic, and easy to follow procedures for site personnel. The purpose of the standalone operations manual is to ensure site personnel who are responsible for undertaking specific procedures, have clear, step-by-step instructions for an individual procedure, without requiring interpretation and understanding of the more comprehensive AMDMP.In adopting a best practice approach to waste rock management for their iron ore mine in Western Australia’s Pilbara region, Roy Hill developed an AMD Management System that is comprised of both an AMDMP and an AMDOM that are connected through adaptive management processes. The Roy Hill iron ore mine, which has a mine life of 18 years, will require the management of more than three billion tonnes of waste rock.CITATION:de San Miguel, V, Miles, B and Pearce, J, 2018. Practical waste rock management at the Roy Hill iron ore mine, Western Australia, in Proceedings Life-of-Mine 2018, pp 80–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Smith, R Gelson

Springvale Colliery is an underground longwall mine situated approximately 10 km north-west of Lithgow in the western coalfields of New South Wales. Following a full-scale review of the mineÆs ventilation system in mid-2010, it was clear that the mine by early 2013 would become ventilation constrained as a result of the increasing size of the mine workings, the predicted worsening tailgate conditions and plans to introduce a fourth continuous miner unit. This realisation led Springvale to embark on a major upgrade of the mine ventilation system that would meet short-term and life-of-mine (LOM) requirements.Included in the upgrade project was the installation of a new high pressure centrifugal main exhaust fan that is capable of overcoming the high resistances imposed frequently on the circuit by restrictions in the tailgate airway. The new fan featuring a 2.5 MW motor is designed to be capable of operating at a quantity of 250 m3/s at a pressure of 7.9 kPa, a substantial improvement over the previous system, which had an operating duty of approximately 145 m3/s at 1.9 kPa. The new fan is of a centre hung design and features a backup diesel motor to maintain ventilation in the event of a power outage.Structural engineering analysis determined that under the operation of the new main fan the existing standard of ventilation control devices (VCDs) at Springvale would not be adequate to withstand the increase in differential pressures. As such, an upgrade of critical VCDs was undertaken utilising a novel high flexural strength (9 MPa) shotcrete and thin spray-on liner, which help serve to safeguard the structural integrity of the appliances and prevent increased leakage as roadway conditions at VCD sites deteriorate over time (a serious problem in many areas of the workings at Springvale).In addition to the main ventilation system upgrade, a separate upgrade focusing on improving development face ventilation was also undertaken. This upgrade included the purchase of two high capacity (22 m3/s) variable inlet vane (VIV) auxiliary fans to facilitate comfortable development face ventilation.The upgrade of the mine ventilation system at Springvale has been three years in the making, but has removed a major business risk in that it has afforded mine planning and operational flexibility (a fourth unit can now be introduced) for the LOM, and importantly provided unprecedented levels of comfort to operators at the working faces where previously ventilation and heat issues were frequently reported. The impact of this on the morale of the workforce, and hence their output, should not be underestimated.CITATION:Gelson, R and Smith, B, 2013. Life-of-mine ventilation system upgrade at Springvale Colliery - A case study, in Proceedings The Australian Mine Ventilation Conference , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By K Sommerville, J Parkinson

"Open pit mines today have more technology and data available. The challenge is to effectively use resources to analyse and identify mine productivity improvements. AMC Consultants Pty Ltd (AMC) has completed more than 100 benchmarking studies worldwide. In the process of gathering cost and productivity data, insights have been gained on how mines are using data to drive productivity. This paper aims to share good practice on using data, what benchmarks operations should be aiming for, where mines are currently sitting, high value areas to target, and how to best prioritise improvement to meet operational goals.A key purpose of data is to assist in managing and improving operations. Key information is used to drive meetings, decisions, budget estimates and reports. Safety, equipment productivity, available stocks, grade and spatial reconciliation are examples of where data is important for management systems. The key is to keep reporting simple whilst maintaining access to source data for troubleshooting and analysis.Some operations still have paper-based reporting systems. Some operations collect data directly off machines and instruments, use cameras and have off-site control centres. The level of technology is a fit-for-purpose choice.Comparisons of productivity assumptions commonly used in feasibility studies with good practice productivity numbers sourced from AMC’s benchmarking database will be shared in this paper. A typical activity mining cost breakdown will highlight where the high value areas for productivity improvement sit.In addition to examining the productivity of each mining step it is also important to examine the impact on the mine plan. Equipment numbers, strip ratio, grade and material hardness can impact the results of bottleneck analysis. A bottleneck example case study will highlight how productivity and other factors can be used to identify and prioritise improvement opportunities.Keep it simple. Use only the critical data for meetings, decision-making, reports and plans. Knowing and communicating the key performance indicators (KPIs) you are striving for aligns the operation and prioritises improvement plans.Citation:Parkinson, J and Sommerville, K, 2016. Getting the Most Out of Technology to Drive Mine Productivity Improvements, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 84–93 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

By A Fern, A Hawkes, o, W Smith, K Mee

Serious Injury and Fatality (SIF) prevention remains a priority focus within high-risk industries sector. A major mining operation sought to strengthen their approach to the management of high-risk activities through an in-depth review of all historical incidents that had serious injury or fatality potential (SIFp) events (sometimes known as hi-potential events). The analysis found that the organisation invested a disproportionate level of resources, time and effort on low consequence incidents with a high proportion of SIFp incidents going under the radar. It was found that 76 per cent of SIFp incidents were rated in moderate or lower risk categories and conversely, almost half of those incidents with a ‘serious risk’ rating had little or no potential for a serious outcome. As a result of this project, the operation engaged in a renewed focus on critical risk management and enhanced its operating cadence in critical risk for the workforce. This included bow tie analysis, an update to critical risk standards and increased workforce engagement in the use of critical control verifications in the field. Data analytics with lead and lag indicators continue to provide senior leadership team and risk owners with an understanding of exposure for SIFp and control effectiveness. The audience will take away learnings from a real-world case study that provides data-driven insights of the human, local and organisational factors contributing to incidents with SIF potential. In addition, participants will understand the steps taken to categorise and analyse this incident data and the initiatives currently being implemented by the organisation as a result.

Apr 16, 2024

By P Marianelli, J Theiler, B Beamish, A Spillman

The presence of reactive pyrite in waste rock contributes to the hazard of spontaneous combustion in emplacement facilities as it acts as an initiator of self-heating at low ambient temperatures. Organic carbon also present in the waste rocks acts as a fuel at elevated temperatures above 120°C and can lead to thermal runaway resulting in eventual ignition. A new laboratory test method (adiabatic incubation testing) is now available that can identify the presence of reactive pyrite and quantify the self-heating behaviour of the waste rock. McArthur River Mine has a waste rock profile that contains pyritic shale units, which have created spontaneous combustion events in the past. A systematic sampling and testing program is underway to characterise the spontaneous combustion hazard likelihood of the McArthur River Mine waste rocks to provide a sound database for future mine planning of the waste removal and emplacement. This paper presents some initial outcomes of this program and shows the leading practice in spontaneous combustion hazard assessment and management that has been adopted at McArthur River.CITATION:Beamish, B, Marianelli, P, Theiler, J and Spillman, A, 2018. Spontaneous combustion hazard assessment of McArthur River Mine waste rock, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 422–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By O Bascur, A Soudek

Large metallurgical complexes are substantial users of energy, water and assets. To improve the effectiveness of energy and assets the quality of the data and events become paramount for real-time operational management. A lack of resources at the local operations and at the enterprise makes it impossible to process the sea of information and many projects have failed. As such, a novel approach for implementation of continuous improvements at the local level and innovations at the strategic level was implemented at all operating plants at Anglo American Platinum. Sixteen concentrators, three smelters and two refinery process systems were integrated to scale the information for manufacturing services at the local and enterprise level. The new capability of an enterprise real-time monitoring and diagnosis software infrastructure was available to implement many business strategies in tandem. Mineral and metallurgical processing knowledge is used to simplify the implementation of the data model. As such, asset monitoring, energy, production and process control management were implemented in an integrated approach reusing the same data but with different context and time horizons to have a standard methodology for local root cause analysis. This paper will highlight a sustainability management approach to change and empower the local and strategic team to collaborate using a new approach for adaptive reporting and condition-based event management and notifications. The results based on the integrated and collaborative team efforts will be presented. OSIsoft Plant Information system was installed and configured to achieve a targeted reduction in energy consumption of 15 per cent by 2015.CITATION:Bascur, O and Soudek, A, 2014. Implementation strategies for energy effectiveness and sustainability – example of Anglo American Platinum, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014