Search Documents

A flow sheet has been developed to treat a high tonnage highly preg-robbing gold ore. The ore is low grade and fine grained with a high proportion of very fi ne free gold. The key components of the flow sheet include gravity, flotation, intensive cyanidation with direct electrowinning, and carbon-in-leach of the flotation concentrate. The circuit produces a low overall mass pull to concentrate allowing economic intensive treatment of large tonnage low-grade material. Efficient recovery of fine gravity gold using a Falcon concentrator in both the milling and flotation circuits, and subsequent intensive cyanidation in a Gekko InLine Leach Reactor (ILR) is critical to the process with over 70 per cent gold recovery expected in this circuit. Grind size control was also found to be important in controlling the activity of the preg-robbers in the carbon in leach circuit and also in the solid liquid separation performance. Tests at the large-scale demonstration plant have been conducted to demonstrate the effectiveness of this flow sheet. A large low-grade deposit is currently under development with the aim of developing a 10 Mt/a treatment plant with the subsequent addition of equivalent sized process lines in multiples of 10 Mt/a. The economic development of this orebody is critically dependant on understanding and exploiting the properties of the ore. In particular it is critical to minimise the effect of preg-robbers by recovering free gold with Falcon concentrators and InLine Leach Reactors. Recovery of the remaining gold by flotation into a small mass yield allows this fraction of gold to be treated by CIL leaching utilising high carbon levels. It is critical is to ensure operation at the optimal grind size to maximise liberation of the free gold and minimise pregrobber activity. The ore has been identified as preg-robbing with low recoveries obtained if treated using conventional cyanidation and carbon absorption. The mineralogy consists of predominantly fi ne grained free gold with minor sulfides including pyrite and arsenopyrite. With conventional cyanide leaching in the absence of carbon, gold recovery is less than 50 per cent. Direct cyanide leaching of the ore in the presence of activated carbon results in an improved but still uneconomic gold recovery. The gravity recoverable gold (GRG - as defined by Andre La Plante) content of the ore has been measured to be 70 per cent to 85 per cent in various tests with liberation grind size of approximately 106 ¦m. This indicates gold is predominantly free and suitable for recovery by batch centrifugal concentrators into a low mass yield. This property of the ore presents the opportunity to maximise the recovery of gold by separating it from the majority of the preg-robbers prior to leaching. Due to the very fine gold particle sizes and the necessity to maximise recovery of this fine fraction Falcon concentrators were selected for the duty, with their proven high recoveries at very fine gold sizes. The gravity recovery in the milling circuit is designed to be in the range 55 to 65 per cent. This has been achieved in the existing pilot plant using a Falcon operating on ball mill discharge within the mill recirculating load. Intensive leaching in an InLine Leach Reactor is essential to recover the gold from the gravity concentrates. Tabling is not a preferred option since recovery is lower than intensive cyanidation and any gold losses to table tails will report to CIL where recovery is reduced by the presence of preg-robbers. Furthermore, tabling recovery from the gravity concentrates is particularly poor due to the fine particle size of the free gold. ILR recoveries of 98 per cent were demonstrated in the pilot plant using an ILR100BA and leach conditions were investigated in the lab using pilot plant generated Falcon concentrate. Recovery of gold from the pregnant solution was achieved with direct electrowinning at pilot and efficiency and sizing parameters were determined at lab scale. To further increase free gold recovery Falcon concentrators will be installed in the flotation circuit. Location of the Falcons in the circuit is not finalised but installation on the rougher concentrate stream is favoured since it will allow multiple pass recovery. This is expected to recovery a further ten to 20 per cent of the gold, as indicated by lab tests on pilot plant generated material. The gravity concentrate from the flotation circuit will also be leached using InLine Leach Reactors. Initial intensive cyanidation tests carried out on lab generated flotation concentrates indicated higher recoveries than CIL can be obtained even though the concentrates contain significant levels of preg-robbing material. This can be explained by the high cyanide, high pH leaching conditions used in the ILR which alters the absorption equilibrium of the preg-robbers. Further optimisation of the leach conditions will be undertaken once more concentrate becomes available. Recovery of the remaining gold content is achieved by flotation into a small mass yield, however the preg-robbers are also recovered into this concentrate. Due to the presence of the preg-robbers gold leaching must be carried out in the presence of high levels of activated carbon in a CIL system. The recovery has been shown to be strongly dependant on the carbon loading and the concentrate particle size. The carbon competes against the preg-robbers for dissolved gold while excessive grinding increases the surface area and activity of the preg-robbers. This has been demonstrated in test work however the economic optimum leaching conditions and carbon loading have yet to be determined. The grind size is critical to the economics of the project, not only due to its effect on gold recovery but also due to its effect on the major operating and capital costs at both the front and back end of the process. It is critical to grind enough to obtain both gravity free gold and flotation liberation at low mass yields however over-grinding results in large increases in mill size and power at the front end and filtration or thickening costs at the tails. Because these unit operations treat essentially all the plant feed even small changes can result in major impacts on project economics. The viability of this project is greatly enhanced by the high recovery of gold into a small mass yield. In particular the production and intensive leaching of the free gold gravity concentrates will allow over 70 per cent of the gold to be recovered efficiently with minimal impact from preg-robbers. By using flotation the mass of the remaining fine preg-robber contaminated material, to be leached in CIL, is greatly reduced allowing this difficult material to be economically treated. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By H Kim, M J. Sun

In order to reduce carbon emissions from the steelmaking process and achieve carbon neutrality, global steel companies are establishing their own medium to long-term strategies and implementation plans using competitive technological advantages held by each steel company. At this point, Hyundai Steel has formulated a product-oriented carbon-neutral strategy based on innovative processing that makes use of Hyundai Steel’s own strength. Based on our experience in electric arc furnace product manufacturing and blast furnace operation in an integrated steel mill, Hyundai Steel is driving the Hy3 (Hy-cube) project, which involves a unique hybrid production system utilising hydrogen and hydrogen-based renewable energy sources. This initiative aims to achieve carbon-neutral production and eventually specialise in producing premium carbon-neutral automotive parts. The project has originality in that it involves not only designing processes using electric furnaces to produce premium steel products such as car body panels and electrical steel sheets, but also aims to reduce carbon emissions from the process, developing carbon-neutral products based on market demand. To assess the feasibility of the Hy3 project, Hyundai Steel conducted two pilot productions. The first pilot was producing a prototype of lower-arm part using electric arc furnace with three different kinds of raw materials: molten iron, HBI (hot briquetted iron), and scrap. Successful performance evaluation of auto parts with 1 GPa strength was achieved. The second pilot has been focused on tire cord steel, with the first-phase tests yielding a 33 per cent reduction in carbon footprint (CFP). Using the advantages of operating experience in electric arc furnace, Hyundai Steel is preparing for test operations producing various automotive parts using an electric arc furnace (EAF) to advance the Hy3 concept. From a medium to long-term technological development perspective, Hyundai Steel’s blueprint includes producing high-end carbon-neutral steel products using hydrogen-reduced iron as raw material.

Jun 19, 2024

By M S. Tuohy

Poorly judged or under-appreciated change plays a role in many major accidents. In particular, operational changes related to continuous improvement, maintenance and introduction of new technology can lead to unintended safety (and other) consequences. This paper provides an overview of the role of management of change in preventing unwanted impacts on safety, community relationships and the environment. It draws on a range of incidents covering mining, minerals processing, refining and smelting where inadequately assessed or ineffectively implemented change led to significant safety, environmental or community consequences. The paper will also highlight cases of well-managed complex change and the underlying model of decision-making in place to make those decisions. All these examples are drawn from Atturra’s experience in response to accidents or working with sites to improve their management systems. The paper will report on the challenges of applying conventional risk assessment approaches to complex or technically significant change. These typically result in either onerous and lengthy change procedures that are prone to workarounds or poor implementation. Conversely, ‘light touch’ or efficiency driven change processes present the risk of intended consequences by failing to bring appropriate expertise to bear in decision-making. Such balances can be resolved by considering the designation of ‘technical authority’ with appropriate expertise to consider the change and deconflict any production, cost or schedule trade-offs. Finally, the paper will reflect on the key components of management of change systems in the context of major accidents, highlighting good practice in how they are implemented. This will consider the integration of existing corporate processes, risk management and organisational structures into management of change systems, not just the content of change forms and procedures.

Apr 16, 2024

Currently all engineering schools face a common problem, an ever expanding technological base which must be presented to students within a fixed time period. Traditionally the programmes of study taken by engineering students destined for employment within the mineral industry include formal instruction in aspects of management to an extent greater than that presented in other engineering disciplines. Providing an adequate coverage of an expanding technological base within a fixed time span can lead to a reduction in the time available for 'non-technical' subjects, such as 'management'. This situation calls for periodic review of course contents and allocations of time. Following consultation with an Advisory Committee representing the mineral industry, mining research establishments, and kindred teaching institutions, the University of Melbourne has revised its mining programme. This programme is offered as an example of how aspects of management such as communications, economics, labor

Jan 1, 1980

By C Paoletti

About 15 years ago the debate on the reliability of sampling procedures for agricultural food and feed commodities was initiated by a few brave scientists who questioned the representativeness of what, at the time, were routine sampling procedures established exclusively on the basis of tradition and practical feasibility. Over time several national and international organisations contributed to the discussion, developing standards and publishing papers either to underline the fact that sampling is always a source of error, in itself, which cannot be overlooked, or to minimise the relevance of sampling on the basis of argumentations linked to time and money limitations. The latter dominated, but is nevertheless impossible to accept from both a scientific and a responsible management perspective. Here the author presents an historical overview of these past 15 years, illustrating the most controversial issues, reporting major achievements in food/feed sampling, highlighting milestones, as well as unresolved problems that still need the attention and contribution from the sampling community. The need to incorporate Theory of Sampling (TOS) into food/feed safety assessment (pre-market), as well as into food/feed safety monitoring (post-market) has recently been highlighted, and the practical applicability of TOS to base food/feed safety decisions on representative sampling, has been explored and documented via concrete examples of risk analysis in different areas of food/feed industrial production chains. Now it is time to move forward and ensure that TOS is fully integrated into the well-established Food and Agriculture Organization (FAO) / World Health Organization (WHO) risk assessment approach, in order to guarantee a transparent and correct universal frame for risk assessment and the subsequent management decision-making process. WCSB8 offers the ideal platform to explore the best way to do so, switching from a theoretical discussion of correct sampling principles for food and feed agricultural commodities to practical recommendations in the interest of consumers, worldwide. These 15 years have also been a personal journey of interesting dimensions, indeed a veritable roller-coaster ride in-and-out of the scientific, technological, industrial and (last but not least) regulatory worlds. The start was WCSB2 in 2004, when I flew to Australia to discover if in other areas sampling had been identified as an unavoidable issue and, if so, what the solution was. There, I found a good travel companion who today is still on my side, to assemble the puzzle and explore how to shape the future, to concretely answer to the 15 years’ quest for proper sampling in the assessment and monitoring of food/feed safety.CITATION:Paoletti, C, 2017. Assessing and monitoring food and feed safety – a 15 year quest for proper sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 39–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By P Lukic

The definition of the working sections that will be used in a mine is usually initially made in the field by the geologist supervising the drilling program. These initial definitions are often made on the basis of rules of thumb such as æcoal less than 30 cm thick cannot be mined separatelyÆ; æpartings more than 30 cm thick will be mined separatelyÆ; and æif a coal seam is less than 50 cm thick and the parting above or below is thicker than the coal, the coal will be wastedÆ. These decisions are also often made based on the requirement for a minimum sample mass for analysis, and the desire to collect data at the minimum resolution to conserve the exploration budget.In many cases the geological models based on this data are produced at a resolution that is inadequate to allow the mining engineer to produce a mine plan that will maximise project value. This problem is generally unrecognised.Where data is collected to a higher level of resolution the subsequent processes employed in the production of geological models and mine plans often discards the inherent value that is hidden in this data. Again this problem is generally unrecognised.This paper highlights this problem and then presents a methodology that ensures that the optimal working section is selected and compares the outcomes of applying this methodology versus adherence to the usual rules of thumb.

Sep 26, 2011

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By B Waldon, M Valastro

A coal dust explosion is one of the most significant risks in the harsh and complex environment of an Underground Coal Mine (UCM). Reviewing literature, regulations and existing systems surrounding explosive dust management shows that there have been few advancements in managing this risk over the past 90 years. Legislation has remained relatively stagnant and minimal systems are implemented in the real world that can simplify, standardise and improve the effectiveness of UCM explosive dust management. To help bridge this gap, Corehesion, in collaboration with an UCM has designed, developed and implement an Explosive Dust Risk Mitigation System (EDRMS) utilising components of Business Intelligence (BI) that is capable of real-world use in industry. To do this the existing explosive dust management process at the associated research mine was evaluated to form high-level and detailed design requirements, focusing on digitally simplifying the procedure, not replicating it. The system was then iteratively and incrementally developed and implemented at the research mine to commence real-world use. The developed BI platform is compared with the existing process to highlight the advancements in performance transparency, efficiency and optimisation of UCM explosion mitigation. This comparison and evaluation of the real-world system implementation at the research mine demonstrate its success in automating procedure steps, providing a readily accessible source of data and enabling a proactive approach to planning and managing explosion risk mitigation. In addition to improvements just for the research mine, this EDRMS created directly address many Queensland regulatory audit findings. By finalising the total system and making the highlighted changes for standardisation, this BI system will have the adaptable capabilities for implementation across the UCM industry. As accurate data availability improves at UCMs, further work can be done to improve the systems’ optimisation techniques and integration of other risks.

Apr 16, 2024

By A Harris, L Balzan

Accurate measurements of the moisture content of iron ore have increasing importance in modern mining operations. Knowledge of the moisture content allows process control actions to be carried out to ensure that the moisture is within prescribed limits, whether this is ensuring sufficient moisture to be above the dust extinction limit or that the moisture level is below the transportable moisture limit for sea shipments. Additionally, controlling moisture within desired limits can allow for greater throughput of iron ore by limiting the amount of water transported. There are a range of options available for operators wishing to obtain moisture data, though there are few demonstrated and proven devices that are able to provide real-time analysis of the full bed-depth of material. Scantech’s through-belt moisture systems are able to accurately analyse the full bed-depth of conveyed iron ore in real time using its unique microwave transmission technology, providing valuable data for operators. Recent advances in these systems have overcome errors associated with the highly attenuating nature of iron ore, particularly for large conveyor belts and deep ore. Furthermore, analysis of different ore mineralogy and its effect on the accuracy of moisture analysis has been examined and quantified. This paper discusses some of these recent results, demonstrating achievable accuracies in spite of changing ore mineralogy. Scope for future work is also briefly discussed, concluding the paper.CITATION:Balzan, L and Harris, A, 2015. Real-time through-belt moisture analysis for iron ore, in Proceedings Iron Ore 2015, pp 539–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Vakili

Dilution is associated with considerable direct and indirect costs in underground open stoping operations. As shown in previous works, an improved ability to predict dilution enables the economic risks associated with unplanned dilution to be reduced. Depending on the width of the orebody and depth of mining, the economic performance of an open stoping operation can become even more sensitive to dilution. It is shown in several well-documented studies that as little as 1 per cent of additional dilution can impose millions of dollars of lost profits per annum. Optimisation of a stoping operation is therefore largely dependent on the ability of the operation to minimise dilution. This can only be achieved through sensible analysis of past and future performance of mined stopes using the most appropriate recent available technologies and tools. This article presents a new design process that utilises advanced geotechnical numerical modelling and various other analytical tools to assist with a more robust mine design of open stoping operations. The focus of this design process is on geotechnical factors affecting dilution during the life-of-mine. A recent application of this optimisation method for a mining operation is presented in this paper as a case study. Through the application of this method and various other operational improvements, the mine was able to deliver more consistent production and lower operating costs over its life-ofmine outlook and was able to reduce dilution by up to 50 per cent and achieve sustainable record high production rates.

Mar 29, 2023

By I Gray

This paper examines the effects of the changes in stress that a coal may undergo as part of the drainage process. As a consequence of this, some coal seams will come to the situation that they have zero horizontal stress existing within them at the time of mining. The hypothesis of this paper is that this lack of horizontal confining stress means that on mining, the vertical stresses may be easily raised to a level where failure occurs. This failure may be accompanied by significant energy release from energy stored within the coal as well as that coming from the roof and floor. To determine the state of stress within the coal seam, the concept of the effective stress path that the coal passes through is examined and is found to be very dependent on the shrinkage of the coal with degassing, the Young’s modulus of the coal and its Poisson’s ratio. The Young’s modulus of the coal is important and has been found to be highly dependent on the state of stress within the coal. It may change by more than an order of magnitude.CITATION:Gray, I, 2014. The consequences for pillar stability of zero confining stress brought about by forced or natural drainage, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 331–336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

By J H. J Holtzhausen

Never has there been more focus on the health, safety, and well-being of our employees at the workplace. Ever evolving expectations of individuals, companies and clients are shaping regulatory reviews and advancing standards across the world in the drive to zero harm. The technology is advancing at a rapid pace, which is now allowing continuous real-time monitoring of contaminants to take place in the harshest of environments.

Oct 12, 2022

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By A Clarkson

Cannington Mine is an underground silver lead zinc operation located in north-west Queensland which has been in production since 1997. Ore is primarily moved through an underground material handling system comprised of a crusher, conveyor and hoisting shaft. The Fowler Shaft was constructed in 1997 using a strip and line method with the intent for it to provide a means to hoist ore from the loading station 600 m below surface. The shaft also serves as the route of key services including high voltage power, mine dewatering and fresh air. Despite the adherence to a mining exclusion zone, large-scale change in geotechnical conditions around the shaft were first observed in 2015. Ongoing ground movement around the shaft lead to cracking and delamination of the concrete liner. Shaft management required the on-site team to measure deformation rates and magnitudes, forecast change, manage rockfall risk and deforming pipework, and ultimately, hoisting skip clearance. Monitoring techniques to observe and measure deformation were required to evolve with the magnitude of movement. Some techniques leveraged off modern technology while some of the most useful techniques were based on logic and first principles. All shaft deformation management strategies relied on the co-operation and alignment between Cannington’s Infrastructure Maintenance, Survey and Geotechnical Departments.

Mar 29, 2023

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

By B Haase, R Saha

Conditional simulation (CS) has been extensively used in metal industry to assess uncertainty of geo metallurgical variables to build robust distributions around grade tonnages across different time horizons. Coal’s entry to nonlinear stochastic modelling is relatively new and this paper summarises the work done at BHP to enable its practical usage from production time frames to Life of Asset planning. CS in coal using Sequential Gaussian Simulation (SGS) is used to understand resource confidence around specific variables within pre-defined boundaries of spatially continuous domains for each coal seam. The variation between simulations for a given parameter reflects uncertainty. This paper demonstrates the use of CS to profile resource based upon agreed seam/parameter uncertainty thresholds which affect planning, forecasting, extraction and inform identification of key production risks and defining mitigation strategies. The end goal is to de-risk long-term plans by optimising infill data collection and improve stability in short-term planning through increased understanding of confidences locally rather than at global resource definition stages. The paper also briefly discusses the use of automated workflows and systems to minimise the time spent on the process to enable use in decision-making.

Mar 22, 2022

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By J Coombes

"In today’s challenging climate of reduced staffing, limited funding and uncertain markets, we are called on to operate more productively and ‘be more innovative’. As an industry, we are quick to identify our practice areas as a mark of our role in the machinery of the mine value chain. We proudly note our profession – ‘geologist’, ‘mining engineer’ or ‘accountant’ – and demarcate our responsibilities and even our physical space. We even subdivide our disciplines into sacred entities such as ‘logging geologist’, ‘resource geologist’ or ‘structural geologist’ to prevent any blurring as though somehow the confusion will cost valuable disciplinary ground. How can we function professionally to heed the call to be more productive and more innovative?The purpose of this paper is to underscore what is expected from project evaluation, examine the ways in which we work as an industry and explore alternatives used in other industries and environments.The paper begins with a summary of project evaluation expectations and the ways in which disciplines typically interconnect when conducting project evaluations. Next, the paper examines alternative work frameworks and making a distinction between multidisciplinary, interdisciplinary and transdisciplinary frameworks. In-practice examples of these frameworks in alternative industries and contexts provide evidence for application as well as an opportunity to examine their pros and cons.The paper closes with a call to re-examine working practices in the mining industry, with a view to enhancing productivity and heeding the call for greater innovation.CITATION:Coombes, J, 2016. Transcending the mining discipline divide – multidisciplinary, interdisciplinary or transdisciplinary?, in Proceedings Project Evaluation 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016