Search Documents

By Yongjin S

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including Modelling.

Jan 1, 1992

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By H Zahiri

Utilisation of the InSAR technique for monitoring of subsidence in mining areas, employing open pit and underground mining methods, has large potential due to sensitivity and safety issues associated with usage of the classical surveying techniques. InSAR can also be very competitive concerning the cost of provided results. However, there are a few issues that may significantly limit InSAR applicability for subsidence monitoring in mining areas. The altered terrain topography, involving steep slopes and deep pits, may lead to the layover of radar signal for specific satellite and pit geometry. Also, the highly dynamic character of subsidence induced by mining, especially using mass mining methods, may lead to issues such as apparent heave and ambiguous results. In this paper the authors analyse the above-mentioned issues and demonstrate how InSAR technology was applied, as a supporting system, to monitor large scale and highly dynamic subsidence for a real case study in Western Australia.

Jan 1, 2008

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

By V Ser, I Smit, C Robertson

Anglo American has been researching the potential benefits of inter-particle comminution techniques for several years. Inter-particle comminution has additional benefits in terms of milling circuit performance such as energy consumption and stability. This paper focuses on the flotation benefits. Inter-particle comminution leads to selective breakage, mineralogical analysis has shown that this leads to improved liberation of the valuable minerals. In addition to selective breakage, the relatively short residence time experienced in typical inter-particle comminution machines allows more efficient classification which contributes to a æsharperÆ product size distribution. The effect of particle size in flotation has been well documented in literature. In general, it is has been shown that there is an optimal particle size range for flotation, and that both above and below this range, flotation recovery is adversely affected. Results show that the narrow size distribution which results from inter-particle comminution improves flotation recovery. Furthermore, the absence of excessive fine gangue material which typically results from conventional fine (-75 ¦m) milling of talcaceous ores, can lead to 100 per cent savings in depressant consumption when such ores are subjected to inter-particle comminution. To-date, this technology has been evaluated on more than ten ores. This paper will focus on one set of results which demonstrates a number of common differences that exist between material that has been milled conventionally and using inter-particle comminution technologies, with emphasis on what the impact of these differences is on flotation performance. A pilot scale (200 kg/h) vertical roller mill (VRM) was used to produce the material, and the results shown will describe conventional laboratory batch, locked cycle and pilot plant flotation testwork.

Jan 1, 2005

By F Anthes, U Barow

Two tunnels are being bored using a æHydroshieldÆ in section 3.1 of the extension of the Underground railway line 5. At the end of the two tunnels, directly in front of the Hotel Adlon, the shields cannot be retrieved. The steel shell of the shield will be left in place within a sealed concrete block and the reusable components taken out through the completed tunnel. For the first time in Germany, an Underground tunnel is being lined solely by means of UNI rings. BerlinÆs Underground network is 165 km long and has 167 stations. Some 450 million passengers are transported annually. On account of the urban planning modifications that followed reunification, the network has to be adjusted, particularly in the city centre. The most significant project is the extension of the U5 from Alexanderplatz to the Lehrter Bahnhof. After completion, the U5 will be a continuous east-west traffic artery. It will provide a direct link with the new parliamentary and government district, open up new business districts and the cultural centre of the city.

Jan 1, 1999

By M E. Pierce

Recent advances in comminution and heap leach technology have resulted in the development of many large-scale, low-grade open pit mines that coincide with areas of historical underground workings. Twoand three-dimensional numerical modelling has been conducted to assess the interaction between open pit slope stability and remnant underground voids. Most design analyses for open pit slopes assume a two-dimensional problem geometry. This is not the condition encountered in practice ù particularly when remnant underground voids interact with a large-scale open pit slope. Three-dimensional numerical models have been shown to provide a more realistic representation of the interaction between overall open pit slope stability and remnant underground voids.

Jan 1, 2003

By M Hudyma

Open stope mining is the most common mining method employed in underground, hard rock mines in Canada. It is characterised by relatively small, single lift stopes (20 000 to 100 000 tonnes), and fast stope turnaround times. Host wall rock mass conditions, which are typically poor to fair, are the controlling parameter in stope dimensioning. Rock mass stability is maintained by designing all stope surfaces at a stable dimension, and through extensive use of cablebolting for stope backs and frequently stope hanging walls. Dilution control is a high priority. The typically small, high-grade, deep and irregularly shaped orebodies are incrementally developed, usually in a bottom to top direction. In many cases, high stress is encountered due to the depth of the orebodies. Overstressing of pillars and hanging pillars are avoided through the use of pillarless or early pillar recovery mine sequencing strategies. Stopes are invariably filled, and in higher grade and wider orebodies, cemented fill is commonly used. This paper generalises many of the similarities found in Canadian open stope mines.

Jan 1, 2000

A shift in the present day oil exploration scenario from West Coast can be foreseen keeping in mind peak of exploration in Cambay Basin and fast pace of development in Bombay High and its associated fields by the end of this century. Shifts in exploration from structural traps to stratigraphic traps, techno- logical development to drill in deep waters, improving economic situation for oil ventures and proven oil and gas potential of East Coast basins suggest that Indian oil explorat- ion scene will be at its peak along east coast during early 21st century. Hydrocarbon shows in Poonch and Jawalamukhi in Punjab Basin, improvements in drilling to greater depths, better seismic data aquisition, good source rock potential of Subathus and its equivalents and large geologi- cally mapped structures will reopen new avenues for explorationists. Not much exploration effort has been put up so far in Ganga Basin. Keeping in mind size of the basin, sedimentary thickness involved, presence of algal matter deposited in shallow marine environment & higher hydrocarbon indications warrant active exploration. Gondwanas in India having such a large sedimentary area can not be ignored keeping in view generation and production from the non marine sediments of Kenya, Chad, Sudan, Gadon and China. Gondwanas become all the more important in view of gas production from their equivalents-Karoos in Ethiopia and South Africa. In all, above mentioned changes can be predicted in Indian oil exploration scenario during 21st century.

Jan 1, 1986

By Segnit ER, Jensen G

The decoppering of soft and hard leads was investigated by stirring in an open pot, using sulfur or sulfur plus pyrites, or sulfur plus pyrrhotite, as reagents. Lead samples taken during the process were analysed for copper. Dross samples were examined by optical micro- scope, SEM and XRD. Soft lead containing silver can be decoppered satisfactorily by stirring with 0.1% S at low temperatures - close to 330¦C. Soft lead, whether containing silver or not, can be decoppered satisfactorily at higher temperatures by stirring with 0.1% S plus 0.4% pyrites. Then CuFeS2, Cu5FeS4 and PbS are formed, instead of Cu2S, CuS and PbS when using S alone. Hard lead containing tin can be decoppered satisfactorily by stirring with 0.1% S at temperatures from 320-400¦C. When stirring with 0.1% S plus 0.4% pyrites, reversion of copper from dross to lead on prolonged stirring does not occur. Hard lead without tin can be decoppered with S plus pyrites better than with S alone, but the presence of antimony hinders the decoppering, which is less effective on lead with 5.5% Sb than with 2.3% Sb.

Jan 1, 1980

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

By Gilligan P

The Selwyn gold-copper operation is wholly owned and operated by the Arimco mining group. The mine is located 150 kilometres south-east of Mount Isa. The primary extraction method for the gold-copper 251 orebody is by sub level open stoping. Secondary extraction is from the mass blasting of the remaining crown and rib pillars. The final mass blast of the 251 orebody occurred in December 1993. This paper details the design and execution of that firing.

Jan 1, 1994

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

An understanding of the importance of the different components that comprise a rock bolt unit is necessary to ensure the proper use of rock bolts as a means of roof support. The various anchors, bolts and plates in use in Australia have been designed and adapted for Australian con- ditions. As mining conditions change, so will the types of bolts in use. This is apparent in the development of chemical anchors and other recent innovations.

Jan 1, 1971

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Beech-Jones J. M

At Port Latta in Tasmania, Savage River Mines operates vertical shaft furnaces for the firing of pelletised magnetite concentrates. At times the temperature profile of the furnace has changed markedly, necessitating the- burning of greater quantities of fuel to maintain good pellet quality. A study of the oxidati=of magnetite concentrates was under- taken because this exothermic process supplies much of the heat required to indurate the pellets. Using the thermal analyses methods, different magnetite concentrates from Australian and overseas were heated in air under identical conditions, to compare rates of oxygen uptake and of heat release. In addition, a compari- son was made of the oxidation behaviour of different particle size fractions of a selected concentrate. Particle size analyses, x-ray diffraction and dilatometer tests were used to aid inter pretation of the thermal analysis traces. The investigation emphasized the importance of particle size and ferrous iron content in determining' oxidation rates from the commencement of heating.

Jan 1, 1974

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste land form. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using the Daydream embankment at Fortescue Metals Group's (FMG's) Cloudbreak Operations as a case study.

May 1, 2010

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

By G King, Q Shu, W Cao, F Gyakwaa, H Singh, S Wang, M Huttula, T Fabritius

Metallurgical slag, such as refining slag, is essential to enhance or promote steel cleanliness. The CaO–MgO–Al2O3–SiO2 system is the primary source of oxides-based inclusions. It plays a vital role in applications in various pyrometallurgical processes. Numerous thermodynamic databases and physicochemical properties of slag studies mainly focus on quenched samples and measurements at room temperature. Consequently, the present study explored the physicochemical, structural properties and crystallisation evolution for CaO–MgO–Al2O3–SiO2 glassy slags via in situ hightemperature Raman spectroscopy and synchrotron X-ray diffraction. The study was carried out by synthesising CaO–MgO–Al2O3–SiO2 slag with varying Al2O3/SiO2 ratios. The results from the in situ high-temperature measurement demonstrated a pattern showing a transformation of a broad peak from the glassy matrix to crystalline peaks. The study showed crystallisation of dominant phases such as Ca2SiO4, Ca2Al2SiO7 and CaAl2O4 that correspond and are attributable to changes of structural units during in situ high-temperature measurements. The results further showed a correlation between an increase and transformation in crystalline phases observed from the spectra obtained from non-isothermal heating of the samples.

Jun 19, 2024