Search Documents

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By G D. Carman

White Rock is a reduced tungsten-tin skarn deposit near Rye Park, New South Wales. This abstract summarises the depositÆs mining and exploration history, and current exploration by Paradigm Metals Ltd targeting an economic resource at the deposit. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By E V. Man, O N. Savassi, J-P Franzidis

In flotation, the property that is exploited to effect the separation of a mineral from an ore is referred to as its floatability. Assessment and quantification of ore floatability is of fundamental importance in modelling and simulation of flotation circuits. This paper describes the design, construction and operation of a new laboratory flotation rig that has been developed at the Julius Kruttschnitt Mineral Research Centre (JKMRC) to determine the floatability of different ores on a small-sale. The rig is designed for continuous operation. The major features of the rig are highlighted in this paper. An unique characteristic of the rig is a 9.1 L conditioning vessel. This provides a mixing regime close to plug-flow which avoids complications such as different collector coverages for similarly sized particles (which would considerably increase the complexity of ore floatability determination). The main advantages of this rig when compared to conventional batch flotation cells include better control of the chemical environment and the ability to determine froth recovery, entrainment and water recovery with increased accuracy. Preliminary tests undertaken with a high-grade lead/zinc ore from BHP Cannington are presented demonstrating the good level of reproducibility obtainable in operating the equipment.

Jan 1, 2000

The decision to contract or owner mine should be independent of, and should be made before, definitive estimated cost comparisons could be available. There is substantial potential risk of estimated cost comparisons being flawed due to difficulties in compiling comparable estimates for differing business objectives, errors and omissions or because of significant bias. In the current economic environment, escalating cost pressures potentially lead to increased incidence of disputes in mining contracts. The apparent cost of contractorÆs profit and overheads has tended to become more significant to owners. Economy-driven trends towards higher levels of performance and commercial risk for contractors, and the potential for more adversarial, difficult management; with attendant disputation between contractors and owners, have encouraged development of so-called ærelationship contractsÆ û partnering or project alliance contracts. The paper discusses the issues, circumstances when owner mining or contract mining is favoured and perceived advantages and disadvantages of contract mining. The implications of owner-perceived core business and core skills and outsourcing are also discussed. Techniques of introducing objectivity into the decision to owner or contract mine using matrix analysis or benefit comparisons are described. A disciplined procurement process should deliver a decision to owner or contract mine independent of, and prior to, any definitive comparison of estimated costs. A generic procurement process model is provided as a basis for discussion. Risk is discussed generally and as a significant factor in comparison of estimated operating costs. Consideration of risk and any prudent cost treatment are promoted as necessary pre-requisites to any comparison of estimated costs. The paper develops the concept that the decision to owner or contract mine should be based on real benefits that become obvious in the early stages of the development, particularly the procurement process; and before definitive estimated cost comparison can be available. In the context of this concept estimated cost comparisons tend to be confirmatory. Problems with comparing estimated ownerÆs operating costs with tendered contract prices are also discussed, particularly recovery of capital cost of equipment; and the owner minerÆs trade-off of operating risks for the residual contractorÆs margin attributed to overheads and profit. The paper concludes that sole reliance on a comparison of estimated ownerÆs operating costs with tendered contract prices in deciding to owner or contract mine is questionable and likely driven by a need to satisfy specific in-house customers.

Jan 1, 2003

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

Botanical exploration has identified many plant species that naturally accumulate very high concentrations of elements, particularly heavy metals. The enormous potential applications of some of these species to remove metals from soil (phytoextraction) are slowly being realised. The discovery of hyperaccumulation has resulted in considerable research into applications for removing contaminants (phytoremediation) or more importantly, in the context of this discussion, for commercially æfarmingÆ metals (phytomining) from metal-bearing soils. Currently published phytoextraction models estimate Ni yields using Berkheya coddii (a South African nickelophyte) are approximately $US 750 ha-1, excluding the cost of processing. Research indicates that B. coddii will also accumulate significant amounts of Co, resulting in a considerable increase in the value of the crop. Modification of the substrate by acidification, fertilisation and/or chelation indicate fruitful avenues for improving this yield by increasing the extractability of the target element, elevating biomass production rates and/or rendering other contained heavy metals extractable. Plant uptake of more insoluble elements, such as Au, may be induced in many plant species using chemical compounds. These chelates applied to the soil, form soluble complexes with poorly soluble metals forcing them into the soil solution. Plants may then accumulate these metal complexes through transpiration. Research has achieved foliar Au concentrations of 78 mg kg-1 in Iberis intermedia, 56 mg kg-1 in Brassica juncea and 9 mg kg-1 in B. coddii (on a dry weight basis). Therefore in theory B. coddii could phytomine a soil containing modest concentrations of Ni, Co and Au to yield 116 kg Ni, 36 kg Co and over 6 oz Au ha-1 at a current value of $US 4000. Root crops have also shown promise in chelate assisted Au accumulation (eg 6.8 mg kg-1 in Beta vulgaris and 118.5 mg kg-1 in Raphanus sativus). Phytoextraction, in its varied applications, is rapidly coming of age as a technology having considerable potential for application in environmental science and the minerals industry. Phytotechnology employs unique plant biochemical behaviours in the rhizosphere, driven by the sunÆs energy, to seek out and concentrate low levels of heavy metals at very low cost.

Jan 1, 2002

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By R Kahnt, S Jahn, D Baacke, M Eckart

Relocation into the Lichtenberg open pit mine of about 110 million m3 of sulfide-bearing and ARD-generating waste rock piled up on the surface is the most important and cost-intensive single surface restoration project conducted by WISMUT GmbH at the former Ronneburg uranium mining site. The waste rock comprises for the most part Palaeozoic shales, limestones and diabases with pyrite contents of up to seven per cent. Waste pile relocation began in 1992 and is scheduled to be completed by 2007. The approach used for relocation has been extensively described elsewhere (Jakubick et al, 1997; Hockley et al, 1997; Chapman et al, 1998; Paul, 2003). Following completion of the backfill that will be up to 60 m above the initial ground level, a dry cover will be placed on top of the backfilled mine wastes. The area to be covered amounts to about 220 ha. Design planning for the final cover placement of which is to begin in 2004 had to be based on a comprehensive cost-benefit analysis over and above compliance with legal requirements. The crucial question to be answered in this respect was to determine û in addition to the expenditure required to ensure reuse, radiation protection and soil protection û the extent to which additional time, effort and money were justified in order to minimise contaminant release from the unsaturated portion of the backfilled pit contributing to total releases into the ground water and possibly achieve savings in long-term operating costs for the on-site water treatment plant. Optimisation was based on contaminant balance modelling for the entire site reproducing dominant physical and geochemical processes. Among the specifics underlying the cover design is that contaminant release from the backfilled open pit must not be considered independently of that from the adjacent flooded underground mine and that a major part of the backfilled open pit will also be submerged. Following weighing of cover-related short- and long-term costs it was found that higher construction costs for the various cover options will not be offset by cost savings in the long-term water treatment. As a consequence of pit flooding, even a costly multiple cover including an impermeable layer will only insignificantly impact on concentrations and loads at ground water spill over points. As a result of comprehensive studies and investigations, a combined cover of cohesive soil material from on-site excavation overlain by a 0.4 m thick storage layer to restore natural soil functions for revegetation was derived and submitted for approval. Together with hydraulic measures, this approach is to meet any requirement in terms of radiology, water protection, stability, erosion protection, and reuse.

Jan 1, 2003

South Africa is a semi arid, water scarce country that has undergone recent major political and social transformation. This transformation has ensured that water management has become a primary environmental concern in the South African mining industry, raising the status of water from an ancillary service to a fundamental factor in mine planning. The coal mining industry has been involved in the development of integrated catchment management plans since the late-1980s when a series of initiatives commenced in catchments where collieries operated. The plans focused attention on water supply and water demand management, the equitable access to water supplies, and intersectoral approaches to decision making, before the promulgation of new legislative and policy frameworks. Development of an integrated watershed management plan for the Olifants River basin, located in the Mpumalanga province, commenced in 1990. The Olifants River is an international river basin of 54 570 square kilometres and shared by South Africa and Mozambique. The upper watershed, locally called the Witbank Dam catchment, will be the focus of this paper. It has an area of 3400 square kilometres and is the major coal mining, power generating, and maize-growing region of the country. The processes embodied in the integrated watershed management plan had no formal guidelines but rather developed in an ongoing fashion over time. The plan commenced with a situation analysis involving the major stakeholders that identified principal technical shortfalls. These shortfalls were investigated under the guidance of multisectoral committees. The Olifants River Forum was started to extend awareness of the initiatives on an informal level throughout the whole watershed. The results of the investigations enabled water quality guidelines to be established for the upper catchment. To achieve the guideline levels additional initiatives were developed including a scheme to manage mine water discharges into the river system, the development of a standard four-step water management process, investigation and development of innovative mine water treatment processes, specifically sulfate reduction technologies, the use of gypsiferous mine water for irrigation, river and dam hydrological models, groundwater models and biomonitoring. Significant outcomes from the process have been achieved including the improvement in water quality in the Witbank Dam catchment. Equally significant have been the development of partnerships between businesses and between businesses and the community specifically in the use of mine water for irrigation. The plan realised a number of requirements for success including, the development of trust, openness and transparency with information, the essential need for consultation and negotiation and the involvement of third parties to validate information. The future still holds the potential for disputes between upstream and downstream water users but understanding, transparency and accountability between all players have, and will in future, enable the matching of the increasing demands on a scarce water resource to the needs of all.

Jan 1, 2003

By D L. Richardson, B Tiedt, C D. Morgan

Following residentsÆ concerns that the ongoing operations of Collinsville Coal (CCP) mine may be resulting in the release of contaminants, including products of acid mine drainage (AMD), into downstream environments, the Queensland Environmental Protection Agency (QEPA) issued CCP with a Notice to Conduct or Commission an Environmental Evaluation at Three Mile Creek. A key objective of the Environmental Evaluation was to assess the extent and magnitude of impacts to aquatic communities and their habitats. A multidisciplinary investigation examined a suite of physical, chemical and biological indicators to meet this objective. The study also aimed to identify contaminants of concern and the location of potential pollutant sources. Potential indicators of AMD, including elevated dissolved solids concentrations and low pH, were evident within the mine lease. However, significant differences in concentration of these indicators upstream and downstream of the confluence with Three Mile Creek were not observed. Although only proxy indicators of AMD contamination, these results suggest that the extent of impacts downstream is minimal. For the purpose of this study, physio-chemical indicators were selected on the basis of those best likely to provide an understanding of the likelihood of contamination, within the constraints of readily available long-term monitoring data. Ecosystem health indicators were adopted to supplement the existing data set and provide a more æroundedÆ perspective of water quality attributes within the system, generally unattainable by standard physio-chemical assessments. In contrast to AMD products, sediments were considered more likely to have a widespread impact on aquatic ecosystems. Waterways throughout the study region, including those unaffected by mining, have been affected by broad-scale sedimentation and were typically highly turbid. Due to the many diffuse sources of sediment potentially liberated within the catchment, the contribution of the mine compared to other land uses on total sediment loads entering streams is difficult to determine. This is clearly a major management issue for mines throughout the Bowen Basin. Streams of the central Queensland region display enormous variability in water flows and physio-chemical characteristics over a range of spatial and temporal scales. This variability presents major difficulties in distinguishing anthropogenic impacts from natural variability (noise). Despite this variability, impact monitoring by mines in the central Queensland district has tended to focus almost entirely upon physio-chemical indicators. The results of the present study indicate that a multiple indicator approach to environmental assessment is more useful for separating mine related impacts from natural ænoiseÆ and impacts from other land uses. In the absence of such information, by adopting the precautionary principle of Ecologically Sustainable Development (ESD), there is potential for an environmental impact to be incorrectly attributed to mining when other activities in the catchment may be contributing to changes in stream æhealthÆ.

Jan 1, 2003

By M Balamurali

In mining, grade control generally focuses on blasthole sampling and the estimation of ore control block models with little or no attention given to how the materials are being excavated from the ground. In the process of loading trucks, the underlying variability of the individual bucket load will determine the variability of truck payload. Hence, accurate material movement demands a good knowledge of the excavation process and the buckets’ interaction with the environment. However, equipment frequently goes into off-nominal states due to unexpected delays, disturbances or faults. The large amount of such disturbances causes information loss that reduces the statistical power and biases estimates, leading to increased uncertainty in the production. A reliable method that inferences the missing knowledge about the interaction between the machine and the environment from the available data sources, is vital to accurately model the material movement. In this study, a twostep method was implemented that performed unsupervised clustering and then predicted the missing information. The first method is Density-based spatial clustering of applications with noise (DBSCAN) based spatial clustering which divides the diggers’ and buckets’ positional data into connected loading segments. Clear patterns of segmented bucket dig positions were observed. The second model utilised Gaussian process regression which was trained with the clustered data and the model was then used to infer the mean locations of the test clusters. Bucket dig locations were then simulated at the inferred mean locations for different durations and compared against the known bucket dig locations. This method was tested at an open pit mine in the Pilbara region of Western Australia. The experimental results demonstrate the advantage of the proposed method in inferencing the missing information of bucket-environment interactions and therefore enables miners to continuously track the material movement.

Jun 22, 2022

By E Whiteman, L Reyneke, H Horsch

Heavy mineral sand deposits are a source for the economically important element titanium, which is contained in minerals such as ilmenite and rutile. In heavy mineral deposits ilmenite displays various degrees of alteration. Natural weathering of ilmenite involves the removal of Fe and thus results in an increase in the Ti-content. Minerals such as pseudorutile, ferropseudobrookite, anatase and the ill-defined mineral aggregate leucoxene, which consists mainly of various amounts of remnant ilmenite, pseudorutile, ferropseudobrookite and anatase, are typical replacement products of ilmenite. Ferropseudobrookite occurs as a recrystallised, optically and chemically distinct mineral phase. Textural relationships suggest a diversity of physicochemical conditions including weathering and metamorphism that led to the formation of complex mineral assemblages and textures. In the heavy minerals industry the alteration products of ilmenite are generally referred to as æaltered ilmeniteÆ and/or leucoxene. The distinction between æaltered ilmeniteÆ and leucoxene is not consequently defined and is very much dependent on economic factors and specific mining operations (ie determined by deposit specific mineral assemblages). Generally the term leucoxene is used in the heavy minerals industry as a collective description for ilmenite alteration products with TiO2-components ranging from 65 - 95 per cent. A detailed comparative mineralogical investigation including microscopic, SEM and QEMSCAN« techniques show that it is possible to identify and quantify the replacement products of ilmenite on a micron scale. QEMSCAN« generated particle maps were graphically compared with photomicrographs taken by applying reflective light microscopy. The resulting information can be integrated over the entire sample with respect to composition, absolute and relative mineral abundances, grain sizes, volumes, densities, textural relationships and liberation potentials. This provides a powerful tool for a first appraisal of the physicochemical behaviour of bulk samples and individual particles during metallurgical processing.

Jan 1, 2008

The use of systematic review methods, derived from System Safety approaches used in the North American nuclear power industry, have become an accepted approach for seeking "approval" for new coal mining equipment and operational changes in NSW. Based on risk analysis, they provide a valuable and needed framework for the reduction of losses related to people, equipment and production.

Jan 1, 1991

A Modelling Approach Using a Back-Calculated Induction Time to Predict Recoveries in Flotation

Sep 13, 2010

Orebodies in the Mt. Charlotte - Hannans North Area N. & B. of the town of Kalgoorlie provide a marked'dontrast to the pyrite - telluride lodes of the Golden Mile, although both groups of orebodies appear to be fundamentally related. These highly siliceous telluride free orebodies N. of the Golden Mile are closely related to strong oblique faulting. The Golden Mile. lodes, while possessing an apparent over-all relationship to the oblique faults also have a close relationship to E.-dipping strike faults.

Jan 1, 1964

A three-dimensional finite element analysis is used to determine the stress intensity factors associated with the chevron-notched semi-circular bend test specimen. The stress intensity factor calibration is done over a range of crack lengths a

Jan 1, 1998

By Guoqing Cao, Xinghong Wang, Fuqiang Liu, Rong Shen, Xiaoping Yuan

In this paper, an approach is proposed to monitor the rate of lump coal based on image processing. Using this method, we effectively improve rate of lump coal on comprehensive mechanised coal face.

Jan 1, 1998

The unique characteristics of the Target orebody and modernistic approach to mining present significant challenges and a concomitant high potential for new opportunities. The break-away from the traditional labour intensive mining methods improves both safety and productivity significantly. The intention of the paper is to illustrate the application of well known mining methods to the particular requirements of a complex orebody at depth. The evolutionary process followed to establish the final mining method design provides insight behind the finished product, and the modern approach to the planning and service principles equips the reader with a suite of mining engineering ideas.

Jan 1, 2000

By R M. Anderson, S P. Pigdon

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of 1 MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998