Search Documents

By S Furman, M Caccetta, A Hacket, B McDonald, M A. Wells, D Lau

In 2004, the Western Australian Department of Industry and ResourcesÆ Burrup Rock Art Management Committee commissioned a number of independent scientific studies to evaluate the condition of rock art in the Burrup Peninsula near Karratha (Western Australia). These studies are evaluating the physico-chemical aspects of the effect of environmental modification on the visible appearance of the rock art. Because of the cultural significance of the sites, the research approach has been to employ non-destructive testing strategies and work in the field has progressed with respect for the importance of the area. This paper only reports the spectral mineralogy monitoring at each of the sites to evaluate whether changes in mineralogy are observed on rock surfaces. Reflectance spectroscopy is a non-destructive, in situ materials characterisation technique that provides information about the mineralogy. The minerals detected include haematite, kaolinite, chlorite, goethite, gibbsite and manganese oxides. Current results indicate that the surface mineralogy of the rock art has not changed in the last four years.

Jan 1, 2008

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

By Hall S. F, Quast K. B Newell R, Ketteridge I. B

For the past six years research funded by the State Energy Research Advisory Commit- tee of South Australia has been conducted at the South Australian Institute of Technology, School of Mining and Metallurgy on South Australian lignites. A major part of this work has been a study of the potential bene- fication of Bowmans lignite using hydrometal- lurgical techniques. The Bowmans lignite de- posit is the largest of its type in South Australia and is a major energy reserve for the state. The utilization potential of this deposit is reduced by its very high insitu NaCl content which presents serious problems for any process. Previous research conducted by Readett and co-workers (1984a & b) has shown that NaCl is amenable to extraction using simple batch water leaching operations. This leaching has been successfully described using a two stage diffusion model derived from first principles based on a simple diaphragm cell.

Jan 1, 1987

By Slattery T. E

Recent develognents in zinc flotation at the North Broken Hill Limited concentrator are discussed. An outline of the history of zinc flotation and a description of current practice is presented. Installation of on-stream X-ray analysis probes has resulted in inproved metallurgical performance and focussed attention on automatic control. Results are presented of investigations made over the past six years which have led to the formulation of experimental schemes for the automatic control of zinc flotation.

Jan 1, 1983

By C Aldrich

In this paper, the use of topology preserving projections (Sammon maps) and neural networks are considered as a basis for the construction of multivariate statistical process control charts for a semi-autogenous grinding circuit on a gold plant. Comminution circuits are often operated in a quasi-steady state mode, where the mills tend to move rapidly from one state to another. This makes them difficult to monitor by conventional means designed for continuous steady state processes. As a first step, process data reflecting normal operating conditions are mapped with SammonÆs algorithm. Only one feature is extracted at a time and each mapping is captured by a neural network model to allow online application. Reverse neural network models are used to reconstruct the data prior to the extraction of subsequent features from the data residuals. The ensemble of neural network models can then be used for both fault detection and identification. The approach compared favourable with both linear and non-linear principal component models. It was able to detect two simulated fault conditions both with a reliability of 100 per cent, as opposed to 57.8 per cent and 95.2 per cent detected by an approach based on the use of linear principal component analysis and 84.1 per cent and 98.0 per cent detected by an approach based on non-linear principal components extracted with auto-associative neural networks.

Jan 1, 2007

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

Deep hydrothermal fluids adjacent to the Alpine Fault move through the brittle-ductile transition to mix with convecting fluids from near surface environments. These tectonically driven fluids evolve mainly from prograde metamorphism at mid crustal depth (ten kilometres) within the ductile regime which has been elevated due to advection and drag on the fault plane. Through the onset of brittle failure and cataclasis within Alpine Fault mylonites, fluid overpressuring results in hydrofracturing and localized implosion. Along the length of the Alpine Fault, hydrothermal alteration varies on most levels (Table 1). There is an observable increase in Fe-Mg carbonate between the Waitaha and Taramakau Rivers (between Ross and Aurthur's Pass, respectively). Field studies concentrate to the north east of the Arahura River, noted for historical mineral wealth. Late meteoric fluids move through cataclasite, brecciated mylonite, and other open fractures. Chloritisation is the major retrogressive phase. Dolomitic hydrofracture veins (Figure 1) within coherent mylonites contain iron and copper sulphides. Notably, the enrichment in Fe-Mg carbonate towards the Alpine-Hope Fault intersection seems to represent a region of enhanced permeability possibly related to shallow seismicity, increased regional faulting, footwall variation, strike-slip dip-slip distribution, and/or topographical anomalies (ie saddles). Isotope studies identifying an 'Inboard Fault Gouge Calcite Zone' correlate to values from the Main Divide region at the headwaters of the Arahura River (Browning Pass-Wilberforce Valley) (Becker et aI, 2000). These correlations are supported by rare arsenic anomalies (avg l06 ppm n = 5, Figure 2) found in both regions which suggest that fluids may be interconnected at depth.

Jan 1, 2001

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

In general, modern mining companies all over the world have to face the same economic circumstances as any other part of the industry: considering the tough competition, production and haulage costs must be reduced permanently whereas productivity has to increase substantially in order to remain price-competitive. However, the imposed pressure also offers the chance for consideration of alternative mining concepts, the application of which can result in substantial cost savings and improvements in the quality of the mined material. As one of these alternative mining concepts, surface mining technology offers substantial improvements in productivity. It also influences aspects of haulage, such as safety and speed, in a positive way. The capability of selective mining ties in nicely with the production of small-sized crushed material, the granulometry of which allows the elimination of the primary crusher. Mine operators profit from reduced costs for the maintenance of their haulage vehicles due to reduced wear, a decreased likelihood of accidents and higher average transport speeds. Surface Miners can also be used to cut haul roads into virgin rocks and leave a clean and level surface behind, improving the quality of these created roads. Thus, it is even possible to use ordinary road trucks for transport in mines. The current paper outlines in detail the effects of the surface mining technology on mining and haulage aspects and reports on applications where substantial cost savings could be achieved due to the application of what is also referred to as æsimple mining processÆ.

Jan 1, 2003

Australia, with its fast-growing economy and high standard of a~ living, has a high and rapidly increasing per capita consumption of energyIn total terms, Australia's energy requirements are doubling every 15 years, and among mature Western economies Australia ranks behind only Italy-and Japan in the rate of increase of energy consumption.The use of energy is often accepted as a yardstick of development and on this basis Australia might well congratulate itself on its high energy consumption. However, it is less well recognised that the resources absorbed in the production of energy represent a real cost to the* community, and that just as we strive for industrial efficiency or farm productivity we should strive for economy in the use of energy fuels.Australians spend annually an estimated ú500 million.on all forms of energy, a sum which represents about seven per cent of the Gross National Product. In all, energy production and distribution absorb the employment of more than 100,000 persons. In addition, the annual capital investment by.the oil industry amounts to some E55 millions, by the coal industry about ú12 millions, and by electrical and gas authorities some E108 millions, in total representing more than ten per cent of annual investment in other than private motor cars and housing,

Jan 1, 1962

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

By C P. de Jager, J J. Taljaard

Over the past 75 years, the mining of platinum has predominantly focused on the Merensky Reef horizon in the western Bushveld region of the Bushveld Igneous Complex (BIC) of South Africa (Figure 1). The orebody is relatively flat dipping at 10¦ to 25¦, narrow tabular in shape and has been mined to a maximum depth of some 1600 m within Anglo Platinum. This has resulted in the installation of up to four generations of shaft systems as mining progressed into reserves at greater depth. In recent years, with the improvement in processing technology and improved economics, in particular with the improved price of palladium, the mining of the UG2 Chromitite Reef is proving economically viable. The UG2 Chromitite Reef occurs below the Merensky Reef in the succession and the normal separation varies from 15 m to 400 m, with the largest separation between the reefs occurring in the eastern region of the BIC. The UG2 Chromitite Reef horizon is now being accessed from existing Merensky mining infrastructure by cross-cutting back through the stratigraphy where appropriate, or by establishing new decline cluster systems from surface, along the extensive strike length of the various mining properties. These declines are generally established utilising mechanised mining techniques. This paper gives an overview of the techno-economic approaches considered and evaluated for the selection of the optimum mining and shaft systems. More specifically, the paper reviews the design parameters used, techno-economics, conveyor versus haul alternatives, logistics simulations, capital costs, system performance, time to market or ramp-up success, important system differences and lessons learnt.

Jan 1, 2005

The perception of the mining industry in the Australian community has changed considerably over the last four decades. This has been partly brought about by changing values and expectations of the Australian community as well as by global factors. The legal environment for the Australian mining industry has undergone significant changes. Among them, the High Court's Mabo decision which confirmed native title rights as part of the common law and environmental legal developments are dealt with particularly. It is suggested that the Australian legal environment is not necessarily the prime cause for Australian mining companies taking their investment off shore. This is a summary on how native title impacts on land tenements and some of the major issues that emerged since the `Mabo decision' and the Native Title Act 1993 are discussed. Environmental legal developments have resulted in liability facing directors and senior management in compliance matters .and in operating mining and other businesses because of changes in community expectations. In the next decade it is suggested there will be many drivers for more changes in the legal environment. Some of these are touched on including the changing roles of the Commonwealth and State Governments, the High Court as -law-makers and the changing relationships with indigenous people in Australia and in overseas countries. The changing legal environment for mining demands a national approach in many areas on the proposition that resource based industries are part of a national industry. The uniform law approach among the States has been taking place but this needs to further. An appropriate task force should be forward to review the entire legal structure and regulations affecting mining on a national rather than a State basis . The mining industry will need to work with expectations of a changing community which have powerful, but sometimes contradictory, interest groups.

Jan 1, 1997

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

By J du Plessis, W Marx

The FutureMine Collaborative Research Initiative has been successfully completed after three years of activity. The main objective of this initiative was to provide applications of research previously undertaken in the DeepMine initiative in terms of realistic solutions to problems facing gold mining operations as they reach for depths beyond 3500 m below surface. The FutureMine initiative was subdivided into four broad streams of technological expertise: rock engineering and seismicity; mining engineering and orebody management; software and communications and ventilation, cooling and refrigeration. This paper presents a summary of research output in this last area of expertise. Broadly, research in mine ventilation, cooling and refrigeration was directed in areas related to the recirculation of air, cyclical use of ventilation and cooling systems, air scrubbing technology, optimisation of chilled water reticulation, obtaining direct cooling at the workface, improving underground refrigeration systems through dry air-cooling and water heat rejection systems and a number of software simulation programs to be used in specific applications and as a tool assisting real-time monitoring of underground environmental conditions.This paper describes in broad terms the outcomes from this section of the research program and proposes ways in which some of these technologies may be combined synergistically in novel systems aimed at maintaining acceptable environmental conditions while reducing the impact on the profitability of operations.

Jan 1, 2005

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

By G, F Beach, D Jazzini, R Rounsley

Over the past 20 years within Australia, there have been a number of incidents at mine sites where ammonium nitrate-based explosives have reacted with certain rock types containing sulfide minerals. These rocks have commonly been referred to as æreactive groundÆ. These reactions have frequently led to fires (particularly in ground susceptible to spontaneous combustion) or premature detonation of the ammonium nitrate-based explosives. Clearly, this introduces an element of risk when using ammonium nitrate-based explosives in these areas. Dyno Nobel has been proactive in developing ammonium nitrate-based explosive products that can be used in these types of æreactive groundÆ environments that minimise the risk of premature detonations occurring. A system for assessing æreactivityÆ of sulfide containing rocks has been developed that can be used in the field. Previous literature has been reviewed, identifying Differential Thermal Analysis (DTA) as the most common method for determining the æreactivityÆ of the ground. In the present investigation, DTA has been rejected as a suitable technique for determining ground reactivity, since it measures thermal reactions at higher temperatures over short time periods, conditions that are unlike those in the field. For example, ground at ambient temperature has been found to react with ammonium nitrate-based explosives over long time periods, reactions that are unable to be evaluated using DTA. Other more suitable techniques have been developed to monitor rock conditions that can be measured in the field and give a good indication of potential ground æreactivityÆ with ammonium nitrate-based explosives. Dyno Nobel is currently investigating the reaction mechanisms of spontaneous combustion in reactive ground, the decomposition mechanisms of ammonium nitrate and the role of inhibitors in ammonium nitrate-based explosives. Once complete, this fundamental research will lead to the further development of even lower risk ammonium nitrate-based explosive products for use in æreactive groundsÆ in a variety of mine environments.

Jan 1, 2003

Small mines exist because of a restricted deposit or a small market. With the right management at the present time the small mine can have lower total costs than larger mines. Charbon is an example of a small mine with a restricted deposit and a specialised product. The development which incorporates a unique rail loading facility and flexible coal preparation plant was achieved with a modest capital outlay and in record time. To remain competitive in future with large scale mines who seek increased production the small mine must achieve increased productivity through automation, higher speed equipment and a multiskilled workforce. Deregulation of the industry, scrapping the Coal Industry Tribunal and the Joint Coal Board would benefit small mines greatly. Management of a small operation also requires multiskills which need to be supported by outside help in the form of consultants and temporary staff. In the 21st century small mines will continue to provide a service to the market.

Jan 1, 1988