Search Documents

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

AND INTRODUCTION The Lochiel coal deposit, a large Tertiary soft brown coal deposit in the mid north of South Australia, is currently being investigated by the Electricity Trust of South Australia (ETSA) as a potential source of fuel for a base load power station. Feasibility studies indicated that the proposed dragline method of overburden removal was viable but economically sensitive to both highwail and dump batter angles. The unusual properties of the unconsolidated overburden sediments and the groundwater regime posed a number of intimately related hydrogeological and geotechnical questions which were addressed before and during the excavation of a trial pit. All strata at Lochiel are of soil strength, and artesian aquifers occur above and below the coal. From the initial evaluation of the deposit a number of hydrogeological questions were defined. These related to the rate at which the pore pressure in the silts is reduced by dewatering, the extent of the reduction in pore pressure due to prestripping, and the feasibility of dewatering and depressurising carbonaceous silty sand sequences. The site of the trial pit was selected to answer these and other questions from the basis of a detailed geological, hydrogeological and geotechnical understanding. The trial pit dewatering system simulated a full scale mine dewatering system and included ten pumped wells, twenty drainage wells, and nearly 400 monitoring instruments. It operated from September 1986 to June 1987. The excavation was carried out between February and May 1987.

Jan 1, 1988

By L J. Reynolds

Gold mineralisation at the Globe Progress deposit is hosted by a geologically complex zone of shearing and brecciation, within a package of deformed metasediments. Mineralisation styles range from quartz breccias and lodes to sheared clay pug zones and disseminated sulfides. A review of the diamond drill core intersections through the deposit indicates that critical hanging wall and footwall contacts can be a combination of sharp or gradational; visual or non-visual boundaries. Approximately 60 per cent of mineralised contacts can be confidently identified visually, particularly where associated with veining, distinct brecciation or shearing, and high sulfide content. However, the gold grade and distribution of disseminated mineralisation can be extremely difficult to estimate visually, with implications for resource estimation and grade control when mining. Using observed drill hole geology and assays, a new geologically based model for the gold mineralisation has been constructed for the deposit to reflect the expected variability of the mineralisation contacts. This new model will constrain resource estimation and also serve to act as a predictive model when open pit mining commences. Nevertheless, careful grade control practices such as drilling, trenching and supervised extraction of ore will be required to maximise ore recovery and minimise dilution during open cut mining.

Jan 1, 2006

The necessity for good management and economic working in our mines and ore-dressing sheds is impressed upon us by the present low prices of all our metals. Silver, lead, copper, and tin have all suffered a heavy decline during the last six or twelve months, and many mines have been shut down simply on account of the low market value of the ore produced. After fully considering the position of the mining industry. I am convinced that considerable improvements will have to be made to make it as prosperous as it ought to be. The most obvious of these improvements are good management, good machinery, and as little interference by directors as possible. If these conditions are insisted upon and carried out efficielltly a poor mine may have a chance to weather the storm.There is no doubt that the present depression is the refilult of over-speculation and general loss of confidence by which the whole commercial system has been affected, and every branch has suffered more or less, mining not excepted. It has suffered heavy losses in the past, and the future is not over bright we are, therefore, compelled to be careful in everything by which mining is affected and savings can be secured.

Mineral resource estimation is commonly based on the accumulation of a series of local estimates. At times, the distribution of these grade estimates is not appropriate to the grade distribution of the data on which the estimates are based. Mineral resource grade estimation has an increased potential of being in error as the grade variability increases. As the mineral commodity value increases, greater grade variability within the mineral resource is tolerated. This paper directs its attention to mineral properties where the data average grade is 20 per cent or more than the data median grade at a specific cut-off grade. A mineral resource estimate is enhanced if it is supported by graphs which demonstrate that the sample data have been separated into appropriate geological domains. Each geological domain has a unique grade distribution signature, which can be graphically demonstrated simply and objectively. This signature will usually be evident well before the Indicated mineral resource estimates are available. The paper looks at the use of the log probability and MedAve plots to assess how effective domaining has been. It further outlines how the MedAve plot can be used to assess the integrity of the mineral resource grade estimate within a geological domain with the data on which it is based. The paper suggests that the overall grade of a mineral resource at any cut-off grade will be closer to the data median grade rather than the data average grade. Tips are provided to ensure that the odds reflected in the data grade distribution are not ignored and hence the risk that the project is affected by unrealistic estimates of the overall mineral resource grade is reduced.

Jan 1, 2003

Structure is the most important control on the location of hematite deposits in the Hamersley Province in the Pilbara region of Western Australia. Unravelling the structural history of mineralised areas, however, is complex because the Province underwent three orogenic events, and three regional extension events followed the main episodes of compression. Steeply E to ENE dipping normal faults immediately predated deposition of the Beasley Quartzite of the lower Wyloo Group after the Ophthalmian Orogeny. Steeply NE and SW-S dipping normal faults predated deposition of the McGrath formation of the middle Wyloo Group, following the Panhandle Orogeny. The resulting interpreted rift was subsequently reactivated and tilted during the Capricorn Orogeny. Late NE trending normal faults are confined to the eastern half of the Province. High-grade hematite deposits occur in rocks that range from intensely folded (Mt Whaleback, Giles Mini) to rocks with less, or only little deformation (Paraburdoo, Channar), suggesting that folding had at best limited influence on ore genesis. In contrast, extensional normal faults are always associated with high-grade hematite deposits, and in particular faults that link the underlying dolomites of the Wittenoom Formation with the overlying iron formation, thus providing a pathway for mineralising alkaline fluids.

Jan 1, 2005

By J F. C L Costa, J C. Koppe

The goal of this study is to characterise co-processed clinkers by identifying the most common minor elements, their distribution in the clinkers and possible effects on the mineralogical properties of the same. The results show the presence of an elevated content of transition metals, especially manganese concentrated in the matrix (up to three per cent) of the clinkers. Anomalous concentrations of arsenic have also been detected, especially at silicate crystal edges. The results indicate that the tracer elements can perfectly be associated to the mineralogical characteristics of the clinkers.

Jan 1, 2008

By Jagger ND

Pressure filters were found to be necessary to produce Elura silver/lead and zinc concentrates at sufficiently low moisture contents for bulk cargo shipment by sea to smelters.The difficulty in obtaining low moistures was due to the fine primary grind, 80% passing 45 microns, and resultant fine concentrates, 97% passing 45 microns.The filtration system was designed to filter up to 90,000 tonnes/year silver/lead concentrates and up to 130,000 tonnes/year zinc concentrates.This paper details the preliminary test work to select Larox automatic pressure filters, and the commissioning and operation of these filters to achieve design criteria for both concentrates. The design criteria for both concentrates have been bettered due to the concentrates being coarser than the design sizing.

Jan 1, 1985

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

Risk Management has been applied relatively slowly in the mining industry. Except for the risk concept application in financial considerations, the application of Risk Management in safety management has been far from satisfactory. When applied it was treated in a global occupational safety and health sense. Regardless of how much the mining industry has progressed over the years it is still, in many respects, `state-of-the-art' business. The safety aspects of mining are well known and yet little understood by the public. Regardless of what has been achieved so far and how much effort has been put into it, mining is regarded as an unsafe and somehow rude business. Safety records of the mining industry vary from State-to-State. Latest mining related disasters in PNG and Queensland and some other fatal accidents support this public perception. They purport a need for change in managing safety in the mining industry. The latest mining fatalities have raised the issue: What must be done to improve safety standards? Duty of care, risk management and system engineering concepts can provide some answers. Risk Management principles which have been advocated for some time provide many answers and explanations and can make safety management more constructive and workable. What has been missing so far is that this concept has neither been applied nor has been modified for its practical application and purpose on a larger scale. A risk management approach to the management of safety and health in the mining industry is addressed, herein. This approach does not attempt to provide the solution. It does, however, provide a basic understanding of what Risk and Risk Management are all about. Rational management of risk is addressed in the life cycle and system contexts. A system of continuous improvement is applied. There is always a chain of events, outcome, exposure, consequence(s), and consequence(s) value(s). It means that development of an event takes place in time and space. Dynamic circumstances have been created in or within the system. It is a decision-making process designed to provide a methodology which is directed not toward a mathematical model but toward easy use and application in dynamic working environment, by decision-makers who can be anybody from either a risk taker or a risk creator. The emphasis is placed not only on arriving at the best practical, possible and fair decision but also on structured and systematic acquisition of knowledge about the system, its hazards and associated risks, hence increasing the decision maker's ability to manage the decision-making process related to the management of risk.

Jan 1, 1995

By M.E. Crump

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-' and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO. colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 -600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

Key incompatible element ratios for metabasalts from the Early Permian Croisilles and Patuki Volcanics, South Island, New Zealand, provide constraints on the tectonic environment in which their precursor ophiolitic protolith formed. Two geochemically distinct metabasalt suites are recognised among both the Croisilles and Patuki rocks. Metabasalts from one suite exhibit the geochemical signatures of depleted tholeiites from oceanic spreading ridges (N-type MORB) or spreading centres in evolved back-arc basins. These N-type tholeiites show high Zr/Nb ratios (Zr/Nb = 37-62) and are depleted in light rare earth elements (LREE)((La/Y)N

Jan 1, 1987

Relationships between lead blast furnace performance and the composition and size distribution of sinter were determined from analysis of lead blast furnace operating data. Sintering plant practice was subsequently modified and substantially improved furnace performance resulted.

Jan 1, 1971

By Mousset-Jones P, McPherson M. J

This paper explains and discusses a computer program developed to deter- mine the optimum combination of fan pressures that will give a required distribution of airflows in a mine ven- tilation system. The program is based on an existing simulator, VNETPC and two experimentally developed relationships: (1) linearity between fan pressures and added regulator resistances and (2) a non- linear convex function relating the system air power and the fan operating Pressures.

Jan 1, 1988

Currently there is considerable interest in the production of DRI in Western Australia to take advantage of intense interest from the Asian market. Most DRI is produced using gas-based processes and is used as a feedstock in electric arc steel furnaces, otherwise known as mini-mills. This paper critically examines the technical and economic issues of various gas-based DR processes available today and recommends the most effective and attractive processes suitable for Western Australian iron ores.

Jan 1, 1996

During the development of Lorca tunnel project in the South-East of Spain, an in-site study has been done, with the purpose of obtaining the characteristics of the different lithological units through twenty-two parameters for the design of the tunnel excavation and support. In the paper both the different works developed and the different methods and criteria followed in the obtention of the parameters are described. The values of those parameters may be useful in similar cases. Also a summary-table of the parametrical characterization for the use in similar studies is given.

Jan 1, 1987

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

In looking towards 2000, it is more than appropriate that we look back on the history of diamond drilling to give us a better understanding of where we have come from and see the significant advances that have been made.

Jan 1, 1992