Search Documents

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

Ion exchange resins are an attractive alternative to activated carbon in both column and resin-in-pulp processes for the recovery of gold from cyanide solution. Resins are widely used for this purpose in the Soviet Union apparently in preference to activated carbons.A wide range of resins are available and the high level of resin technology is demon-strated in the resin processes used to recover uranium.The anionic gold complex, Au(CN) 2 , is selectively adsorbed onto weak and strong base resins. However other anionic cyanide complexes, cyanide ions and other anions from the process water are also adsorbed onto resin sites. Resin selectively for gold is not as high as it is for activated carbons. As a result similar gold loading capacities are obtained for resins and carbons when used in plant liquors.

Jan 1, 1984

The flotation circuit handling Peko ore at Peko Mines N.L. was examined in July 1970 with a view to determining simple changes in circuitry or reagents which could improve the grade and recovery of the final copper concentrates. The investigation included sampling over one shift followed by detailed testing of the samples by sizing-assays, sizing-mineralogy and sizing-liberation. Mass balances were carried out over total streams, the component minerals and the copper contents. Some laboratory work was carried out to assess the effect of salinity on flotation. In order to handle the sizing-mineralogy calculations a computer programme was set up. The raw data were corrected for locking factors, then mineral and elemental distributions cal- culated for each screen fraction and the total sample. Calculated assays from grain counting were compared with chemical assays. Recoveries through the size-ranges re- vealed very rapid flotation of copper minerals at sizes below 350 mesh. This pointed to a possible circuit improvement by desliming rougher tailings ahead of the scavenger stage. A strong correlation was found between water in concentrates and gangue recovery for the subsieve sizes. This pointed to clean water additions to the cleaner circuit as a way to 1 Project Consultant, The Australian Mineral Development Laboratories, Adelaide, South Australia.

Jan 1, 1972

By D Van Doorselaere

The purpose of blasting during mining is to produce a muck pile that can be efficiently loaded and transported. There is an increasing awareness of the variation in muck pile characteristics and its economic implications. It is well known that good fragmentation by itself is not sufficient to optimise the muck loading efficiency. The swelling and configuration of the muck pile also significantly affect the productivity of the loading equipment. The characteristics of a muck pile depend upon the blast design parameters, explosive properties and rock mass geology. This study has focused on the dependence of muck pile configuration on blast design parameters, explosive properties and size distribution of the muck.The field work was done in two phases. In the first phase 12 blasts were monitored, while in the second, three blasts were monitored. The blast design parameters and explosive properties for each blast were documented and the following muck pile characteristics were measured:muck pile height and its distance from the facedistance of throwwidth of the power troughsize distribution by image analysis technique.The effects of burden, bench height, heave energy of explosive, row-to-row delay, powder factor and the mean particle size of the fragments on muck pile configuration were examined. It was observed that muck pile height and distance of throw are strongly influenced by the burden, bench height, heave energy of the explosive and the size distribution of the muck. The width of the power trough depends upon the row-to-row delay, powder factor and total burden. In addition, the effect of the fragment size distribution on the muck pile parameters has also been discussed.CITATION:Singh, S P and Van Doorselaere, D, 2015. The relationship between blasting parameters and muck pile configuration, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The impact on metallurgical operations of the hydrocarbon energy price hike can be greatly alleviated by recourse to alternative fuels. Information is provided on fuels such as coal, coke, coal-oil mixtures, manufactured gas, wood and charcoal; techniques such as direct and indirect combustion, pulverised fuel injection, slurry burning, fluid bed combustion and various gasification processes. Actual examples of metallurgical operations are used.

Jan 1, 1981

n One of the most interesting and economically important developments which has .`taken place- in the Kalgoorlie Field over the past twenty .years is the proved penetration of ore into - caicò schist. which:has been established on the North Kalgurli Mine. 'This is quite extensive, both. laterally and ' in -depth, and has occasioned-,'" ccasioned ' " some madification.of geological thought In the search for additional ore sources:. .Ore has been mined in calc schist almost since the' first major: gold::discoveries-were made,. and the principal 'features of the various types of depos:itl are well covered in the literature ' of the field. ' However, occurrences in caic schist have not-been characterised by the same degree of continuity or frequency as the innumerable lode formations in- the more -favourable quartz dolerite, ' and there has been a tendencyAo regard,them as isolated and discontinuous ore bearing structures, occurring only under very special-- conditions. It is not intended-:to describe the whole' range of caic schist ore occurrences in this paper, but only major controlling structures, whose penetration therein has been definitely established, and in which an appreciable .amount.of,_ore.has, been and is still being. found.. . It is considered that -similar stiiictiires: may present a' major objective for future exploratory work in other parts of the field'.

Jan 1, 1964

By A G. Pavlides, B L. Weekes

The Sepon Copper Project is located in the Savannakhet Province of Laos PDR and is operated by Lane Xang Minerals Ltd (LXML). An Ausenco - Bateman Engineering joint venture, the Khanong Development Group (KDG) managed engineering, procurement and construction of the project. The plant was fully commissioned in March 2005, two weeks ahead of schedule. The plant is designed to produce 60 000 tpa of cathode copper. The process flow sheet includes a pressure oxidation (POX) circuit that leaches pyrite flotation concentrate to generate ferric ions and sulfuric acid for use in atmospheric leaching of a predominantly chalcocite ore. The process is unique in that the chemistry in the autoclave is forced to produce a basic ferric sulfate precipitate for downstream recovery of ferric iron. This paper describes the design, construction and commissioning of the pressure oxidation circuit. The challenges imposed on construction and commissioning due to the remote location of the site, landlocked status and underdeveloped infrastructure in Laos are highlighted.

Jan 1, 2005

By S McKnight, S Hall

Much of the research regarding the use of bacteria for the oxidation of sulfide minerals has been conducted using pure bacterial strains or synthetic minerals, often under ideal conditions, which does not reflect the conditions commonly encountered in commercially operating plants. This has also led to much conjecture as to the exact mechanism by which bacteria are able to enhance sulfide oxidation and as to which species of bacterial microflora are the most dominant. Recent advances in 16S rNA sequencing has confirmed that many of the bacterial species once thought to dominate commercial oxidation circuits were simply more willing to grow under the culturing conditions used and may only play a minor role in the oxidation process (Rawlings, 2002). Consequently this research will look at bacterial oxidation under conditions more reflective of commercial operations, focusing on the presence of organic carbonaceous material within a refractory sulfide orebody to be sourced from the Fosterville deposit of Perseverance Corporation Limited.

Jan 1, 2004

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

By E Kozan

The paper presents new developments of the methodology of open pit coal production scheduling optimisation. They deal with the specific features of the exploitation of single coal seam and utilisation of truck-shovel and dragline systems. A production scheduling optimisation model is developed as a linear programming problem. The objective function maximises the net present value of the mining project under the technological constraints for meeting the demand function of the coal processing plant and effective utilisation of the available production equipment. Both principles of mine planning, coal quality optimisation and waste deferment are incorporated in the model. Results of a case study are provided to illustrate the applicability of the optimisation model.

Jan 1, 2003

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

By J Rapkoch, M Cerna

As long as the tendency of Chilean copper ores continues to feature high levels of impurities, the smelters will tend to produce high-impurity mattes. The most notable impurities include As, Sb, Pb and Zn. Producing high-quality copper with such materials is a major challenge to metallurgical engineers and operators. More investigations into process optimisations and/or alternatives are needed, using both theoretical knowledge and operational skill. Converting of matte in Chile depends on the matte grade using established technologies. Mattes up to 66 per cent Cu, such as those from Outokumpu Flash furnaces, are converted in two stages, while typical Teniente Converter mattes, ranging from 70 - 74 per cent Cu are converted in one blow, directly to copper. In this paper thermodynamic data are used to evaluate possible variations in the use of traditional technologies applied to smelt copper concentrates with high impurity levels. The results of this analysis help to predict the impurity distributions between matte-slag-gas during the slag blow, and between copper-slag-gas during the copper blow. For converting high-impurity white metal, the effectiveness of volatilisation in the slag blow is analysed. In the copper blow, the type and the amount of flux (SiO2, CaO and others) are altered with the aim of optimising impurity distribution to the slag and gas.

Jan 1, 2005

By T Ross, S Cameron

The requirement to use explosives in ground temperatures exceeding 50¦C is becoming more common as mines work to maximise the recovery of their resources. Orica Explosives was requested to assist in the development and implementation of æhot blastingÆ safe working procedures at Liddell Coal Open Cut in the Hunter Valley. The mine operator, Hunter Valley Earthmoving (HVE), had to contend not only with elevated temperatures in their overburden resulting from burning coal beneath, but also old underground workings which tended to exacerbate the problem. The paper discusses the following issues:the consultative process that was used to develop the procedures employed to ensure the process could be carried out safely; the technical issues surrounding blasting in hot ground, including temperature monitoring, product selection, application and design to ensure safety and performance were maintained; the need for confidence and trust in the team that was working together in a potentially hazardous environment, the emotive issues that were encountered and how they were addressed; the value of a regular review process combined with open and honest communication to ensure the procedures represented best practice and that all stakeholders understood the process; and the value delivered to Liddell Coal when sterilised areas of coal became accessible with little disruption to the mining process. The paper also discusses the challenges that were encountered in the Reservoir Block where proximity to major power lines and rail infrastructure meant that hot blasting procedures had to also consider vibration limits and the need for Energy Australia to disconnect the power.

Jan 1, 2001

A formalised approach to risk management has been regulated in the United Kingdom (UK) since the Construction (Design and Management) Regulations 1994 (CDM) came into force in 1995. These regulations have recently been revised in 2007. In response to a series of significant claims around the world the UK insurance industry published a code of practice for risk management of tunnels in 2003, and that was followed by an international version in 2006. Probably one of the main contributions of this new approach is the recognition that health and safety risks can best be addressed early in the process, initially by the owner and then by the designers. One of the aims is to achieve elimination of risks by good design. The advantage of a risk-based approach to tunnel design is that all risks are considered explicitly, and any residual risks in the design are communicated clearly to the construction team. This paper looks at the implementation of this formalised approach to risk management with reference to the A3 Hindhead Project. The design has been undertaken in accordance with the requirements of the CDM regulations, and also in compliance with the Joint Code of Practice for Risk Management of Tunnel Works in the UK. An outline of the risk-based design process used is provided, including examples.

Jan 1, 2008

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

Shortly after the outbreak of war in September, 1939, it became apparent that considerable quantities of certain metals and alloys which at that time were not being produced in Australia would be required in increasing amounts for the prosecution of the war effort.Australian industry had relied on overseas sources of supply for the relatively small quantities of many special metals which were needed under peacetime conditions. As the war progressed so great became the demand for mooy of these alloys in Great Britain and other allied countries that it was necessary for them to place an embargo on the export of these materials, and thus it soon became evident that if Australia's production of munitions was to expand and develop it would be necessary for her to become independent of overseas sources for many of these essential 'items. The shipping position also became very acute, and this, accentuated the difficulties of obtaining these alloys. Because of the conditions outlined aqove, the manufacture of over thirty different metals and alloys .was undertaken at Newcastle during the past decade. It is with two of these that this paper proposes to deal. They are tungsten powder and ferro-silicon.TUNGSTEN POWDERTungsten is a rare and comparatively new metal. It is used extensively in the production of high speed tool steel, some grades of which contain up to 22% tungsten. Such articles as twist drills, reamers, milling cutters, and lathe tools are made from tool steel, and the demand for these during the war years was greater than ever before. The use of tungsten in the manufacture of high speed steel was first developed in 1914 by the Germans, and when it was discovered that they were using tungsten bearing steel for the production of munitions there began a world-wide search for ores of this rare metal.

Jan 1, 1947

By W L. Lane, T R. Yanske

The Doe Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 m in height and the use of slinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction becoming a major portion of the overall production and have added to the mine life of Doe RunÆs six operating mines.

Jan 1, 1998

By C Zhang, G Si, J Oh, X Zhu

The presence of rock joints has a huge impact on the strength, deformability, and permeability of fractured rock masses by providing surfaces of weakness on which further deformation are more prone to occur, and by serving as the major channels of water flow due to low matrix permeability. In earlier studies, water flow-through rock joints is often assumed as laminar flow between two ideal smooth parallel plates, and the well-known cubic law was derived and widely used to characterise the hydraulic behaviour of rock joints. However, natural rock fractures are irregular and of spatially varied aperture. Thus, the concept of equivalent hydraulic aperture was introduced to modify the cubic law. Numerous works have been conducted on the relation between hydraulic aperture and mechanical aperture incorporating various geometrical parameters. The surface roughness is one of the most sensitive factors for water flow-through rock joints. The aperture distributions are irregular in natural roughed fractures relative to the parallel plates. Barton et al (1985) and Olsson and Barton (2001) incorporated the joint roughness coefficient JRC in evaluating hydraulic aperture and proposed an empirical equation based on fluid flow tests. However, their equations do not conform to the dimensional consistency. Many other researchers (Zimmerman and Bodvarsson, 1996; Xiong et al, 2011; Li et al, 2019) considered aperture distributions in their equations. But the aperture distributions change during shear was always neglected. The contact of rock joints also has a significant impact on the hydro-mechanical behaviour of rock joint, since fluid tends to flow-through a rough joint along connected channels while bypassing the contact obstacles with tortuosity. Nonetheless, previous research mostly considered joint roughness or aperture changes based on 2D joint profiles, while the contact and tortuosity based on 3D surfaces were often overlooked. Only a few works have been made on quantifying the effect of contact area on flow behaviour (Walsh, 1981; Zimmerman et al, 1992; Zimmerman and Bodvarsson, 1996; Yeo, 2001), and mostly ignored contact area change induced by shearing and the associated impact on flow behaviour. Summarily, the quantification of fracture geometry effects on water flow in single rock joints still needs further investigation, especially when considering coupled shear-flow processes. This paper, therefore, aims to study the impacts of contact area and aperture distributions of the single rock joint on the flow behaviour. The evolutions of contact area and aperture distributions induced by shear are considered. Then, an improved model for estimating the hydraulic aperture with the mechanical aperture incorporating the above factors is developed. Finally, a series of shear and shear-flow tests are conducted on artificial joint samples and the model performance is verified by comparing against the results of experimental tests.

Nov 29, 2022

The paper describes a simulating method.for ground water contamination originating from industrial and mining activrty. The finite difference model simulates heat, mass and solute transport. The applied stochastical method for dispersion provides more accurate solution of mass transport modelling. This method gives a more realistic approach of chemical processes in an aquifer depending on temperature.

Jan 1, 1988