Search Documents

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By Wakamatsu DT, Nakahiro Y

This present paper deals with the fundamental study of the separation of fine cassiterite and quartz by liquid-liquid extraction using iso-octane as an oil phase, dodecylamine acetate (DAA) as a collector, and sodium chloride as a depressant. With regard to the distribution of fine cassiterite and quartz between oil and aqueous phases, the effect of DAA has been investigated in terms of pH, DAA and NaCl concentrations, zeta potential, and adsorption density. From the results of the experimental work, a maximum recovery of cassiterite in the oil phase was obtained with pH around 6.0, DAA concentration of 1.0 x 10-5 mole/litre, and NaCl addition of 0.1 mole/litre. In these conditions of liquid-liquid extraction, most of the fine quartz remained in the aqueous phase. Thus it was found that NaCI was an effective depressant for fine quartz under optimum conditions. A series of separation tests by liquid-liquid extraction was then conducted for the mixed samples (6.0 per cent Sn) of cassiterite and quartz. By a single separating process, the per cent of recovery of cassiterite in the oil phase was about 92 per cent with a grade of 27 per cent Sn. The same results could also be obtained by using kerosene in place of iso-octane as the oil phase.

Jan 1, 1993

Coal mining in the Illawarra commenced in 1848. By the early twentieth century mining operations were spread over quite a distance along the coast centred on Wollongong. By this time there were already numerous tunnel mines and one shaft mine. Coal was first reported in Illawarra by Lieutenant Flinders on a voyage of exploration, southerly along the coast from Sydney in 1796. Because of the topography, particularly the escarpment and the narrowness of the coastal plain, access from Sydney was not easy by land and the normal access was by sea. It was not until some coastal areas had been developed for agricultural purposes that the mining of the seams on the South Coast commenced for the supp- ly of fuel. The most important mines in the early nineteenth century were Bulli and Osborne Wallsend. In general, coal was won from the tunnel mines and was transported directly, usually by tramway, to the nearest shipping point. Considerable hardship attended the earliest attempts at mining coal in regard to materials for mining and the way of life of the miners in the vicinity of the mines. With the growth of production and the installation of coke ovens at some mines the area, hitherto virgin bush- land, began to take on a more industrialised appearance. The mines were necessarily small,

Jan 1, 1976

The Archean Gossan Hill Group at Golden Grove, Western Australia, hosts two potentially economic volcanogenic massive sulphide deposits. The volcanic-sedimentary succession hosting this mineralisation is composed of a facies association which includes the products of rhyodacitic to,andesitic effusive volcanism, mass-flow sedimentation and concentrated hydrothermal fluid discharge, in a deep subaqueous setting. The Tertiary Kuroko deposits of Japan are widely compared to Archean volcanogenic massive sulphide deposits and a comparison of the facies associations hosting this style of mineralisation, in these two successions separated widely in time, allows a refinement of facies models suitable for exploration in ancient successions. The required deep subaqueous environment for the formation of volcanogenic massive sulphide deposits places constraints on the physical processes that can operate during accumulation of the host stratigraphy. Limitations on the operation of physical processes is reflected by the resultant facies association which can be used to characterize suitable volcanic-sedimentary successions in which volcanogenic massive sulphide mineralisation may be present. The facies association includes: (1) proximal effusive volcanic products - lavas and associated autoclastic breccias (2) distal volcanic products - mass-flow resedimented pyroclastic debris (3) background sedimentation - reworked volcanogenic and terrigenous mass-flow sediments and (4) chemical sediments - exhalites including cherts, sulphides and oxides, with perhaps various carbonates and sulphates. Primary pyroclastic deposits are not expected to be present, other than distal water-lain air-fall deposits, derived from shallow to emergent basin margin explosive volcanic centres, which also provide a source for the resedimented pyroclastic debris.

Jan 1, 1987

By Szymanski J

The problems associated with underground mining continue to grow in size and complexity. As a result mine management is becoming aware of the benefits that can be achieved through the use of computer-oriented tools for system analysis. When such tools are employed in conjunction with benchmarking practices, the drivers of the system that lead to superior performance can more easily be determined. This paper discusses the use of the Simulation Language for Alternative Modelling (SLAM II) in the determination of the drivers of an underground room-and-pillar mining system. The mining operations included in the model consist of extracting, loading and hauling of the coal using continuous mining equipment in a room and pillar system. Equipment specifications and mining techniques used in the model are based upon current methods employed at the existing underground coal mines worldwide. The model developed is capable of adequately predicting the operational performance of the real world system from a statistical point of view. The results from the study show that computer simulation is an excellent tool for evaluating various mine configurations and for gaining a better understanding of the mining systems.

Jan 1, 1995

During the past decade geopolymer technology has emerged as a possible solution for the effective stabilisation and solidification of waste materials. Amorphous to semi-crystalline geopolymers form by the co-polymerisation of individual alumino and silicate species, which originate from the dissolution of silicon and aluminium containing source materials at a high pH in the presence of soluble alkali metal silicates. It has been shown previously that geopolymerisation can transform a wide range of waste alumino-silicate materials such as fly ash and blast furnace slag into building and mining products with excellent chemical and physical properties, including high compressive strength as well as fire and acid resistance. These chemical and physical properties suggest that geopolymeric matrices derived from waste materials are well suited for environmental and other applications such as the encapsulation of mine tails, the immobilisation of heavy metals and also the fabrication of structural products. The current challenge is to demonstrate that a wide variety of natural Al-Si minerals could serve as potential source materials for the synthesis of geopolymers. Moreover, it should be shown on a large commercial scale that it is possible to encapsulate waste materials into the geopolymeric structure without compromising the chemical and physical properties of the final product for the desired application.

Jan 1, 2000

As an environmental "pollutant", noise is different. For one thing, it is localised (as opposed to transfrontier) and, for another, relatively low levels can trigger very strong human reaction. The reactions, which are annoyance-based, range from mild to violent and do not always correlate well with the levels experienced. This paper draws on technical aspects of noise to consider control and control principles and balances them with the subjective nature of the perceptions and reactions. It is critical to bear in mind that health effects resulting from noise are secondary to the primary human reaction. It is also important to appreciate that annoying noise levels are usually well below those which cause hearing loss. Large mines tend to be remote from cities and towns and the country surrounding such mine sites is often inhospitable. In general, residences near large mines are committed for use by mine personnel and annoyance from mining noise would be rare. Noise problems at long term operations are often a result of secondary activity or land use. As a pioneer mining community develops, secondary and service industries may be established and a township created. With changes in way of life, the perception of problems also changes. Therefore, it is never too early to plan for noise abatement, particularly because noise is only one of a number of environmental and community concerns. Ihny environmental problems are associat- ed with development or expansion of smaller open cut facilities such as hardrock quarries. There is an ever-present need to reduce product cost by mining or quarrying deposits close to the end user and many local authorities have to operate quarries for undertaking their civil engineering responsibilities.

Jan 1, 1987

By R Farana

The future challenges in mining instrumentation, mainly on future intelligent mines, are to continue providing instruments with the highest level of reliability at the lowest possible cost, and also to take advantage of technology existing in other industries and to adapt it to the mining context. New wireless instruments (smart sensors, smart actuators, smart controllers) would also be very useful, as well as instruments fully adapted to the monitoring of large movements that are observed, in both underground and open pit mines. Mining instrumentation is found to various degrees in most mines, both open pit and underground. Smart mining instruments present a certain number of aspects specific to the environment in which the instruments are installed. Namely, the instruments can be installed either for short-term or long-term purposes. The mining industry is always looking for useful instruments that can provide relevant information on ground behaviour adjacent to mining stopes or permanent infrastructure. The instruments must meet the various criteria, and must also evolve with the new mining technologies that are continuously being implemented. A strong collaboration between the mining industry, research organisations, and instrument manufacturers is the key to meeting these objectives. This contribution describes the current trends on smart sensors and smart instrumentation with Wireless LAN support.

Jan 1, 2003

A thousand writers have harped upon the wondrous nature of the inventive faculty. They realise that man is a creator, and that capital and labour alike are, and will always be impotent without machinery and processes that is invention. What Bacon has said is echoed by them all, "the introduction of new inventions seemeth to be the very chiefest of human actions. The benefit of new inventions may extend to all mankind-they make all men happy without injury to 'any' they are new creations and imitations of God's own works." My remarks will occupy another field I will refer to some of those features of the Patent Laws of different countries, which prevent the use of new inventions, oppress the development or inventive' genius, and diminish human happiness and progress' Wherever Patent Laws are framed and administered upon wrong principles, these results are inevitably found. A concise, complete, common-sense comparison of the chief Patent Laws of the world cannot easily be found but to avoid seeing scrappy, misleading references to Patent Law in the press particularly the English-would be equally difficult. Writers who are considered authorities so frequently make minor issues prominent and so uniformly fail to give weight to fundamental principles that the effect on the public is to mislead.

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932

To the south and west of Broken Hill lies the Thackaringa silver-lead district, about 25 miles, and is the locality really of the first silver find in the country long before Broken Hill, the geological fomations of which it much resembles. The Iocks and their structure are identical, except that in this area they are  more irregularly foliated and apparently much more faulted and expose in places quick successions of complete anticlines and synclines, even in a single lease. Saddles of ore respectively are found coinciding with the flexures of the rock but many minor veins otherwise and branches exist and make connections which render the whole a mining problem. It follows then that the surface.of the ground after some denudation in dotted with croppings of all the series, and in such a confusing way that the actual strike of a vein may be even confounded with the dip and readily mistaken for it at a few places. The main character of the outcrops are those usual in the district consisting almost wholly of argentiferous and silicious ironstone, sometimes gossan, which at a depth in a few feet changes to a gangue of very silicious carbonate of iron (crystallised), which occurrence is uniform through this district.The exploration of the lodes has not been extensive as it has not been well understood. Shallow shafts and drives have comprised nearly all the mining at present, which is evident on first sight by the numerous shafts and small excavations dotted 'about, as in an alluvial field. The depth of exploration underground in one place had gone several hundreds of feet, never more than 150 feet vertical from the surface in depth and irregular. The undulations of the most continuous work in this direction is such that it presents at different places successively either a tunnel, shaft, underlay winze, level, or Tise, and is on ore all the time, and where the rocks are faulted (which occurs as much as 30 feet and more) these changes are very abrupt, but for working on are suitably connected by the management.

Oxy-ACETYLENE system of welding and cutting is at present practised in two forms, which may be described as the high and lowpressure systems. In the high-pressure system the two gases, oxygen and acetylene, are delivered. to the blow-pipe under pressure from properly constructed trade cylinders. Oxygen cylinders are in two sizes, each containing 100 and 200 cub. ft. of gas respectively. These cylinders are charged to a pressure of 120 atmospheres, or 1800 lb. per sq. in. approximately. The acetylene cylinders are made in one size as far as the writer knows, and contain 200 cub. ft. of acetylene gas at a pressure of 10 atmospheres. Each cylinder is provided with a valve and connection for attaching a regulator to "break down" the high pressure in the cylinders to the necessary low working pressure of the blow-pipes, and to deliver the two gases at a constant pressure irrespective of the variable pressures in the cylinders. These regulators can be adjusted down to as low as 1 lb. and are provided with two pressure gaugesone reading the contents of the cylinder in atmospheres, and the other the working pressure in lb. per sq. in. The high-pressure, or "two cylinder" system is compact and can readily be transported from place to place in the works. For this purpose the two cylinders are mounted on an easy-running 4-wheeled truck, which the operator and assistant find no difficulty in manipulating. In the low-pressure system the two gases are delivered to the blow-pipe, one from the oxygen cylinder and the other from the acetylene gas generating plant, which consists of the following:Generating cylinder, half filled with water, into which the cathoide is plunged. The generated gas is passed through a filter to the gasometer, then through a water washer on to the hydraullic seal...

Jan 1, 1922

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992

By P Elliott, D Pershke

In a minerals processing context, sustainability is about using natural resources more efficiently to achieve maximum economic benefits with minimal environmental impacts. It embodies five overarching themes, which the paper will illustrate with practical examples from Australian minerals processing plants. These are:resource utilisation and materials efficiency,process waste reduction and enhancement of co-product values,reduction of water use and impacts,reduction of energy requirements and greenhouse gas emissions, andenhanced control of minor elements and toxic materials. Sustainability could be embedded profitably in minerals plant design in three dimensions: 1.technology,2.design, and3.operations. This presentation discusses a set of principles that could be applied to minerals processing technologies and provides an outline of sustainability assessment and opportunities evaluation tools. The application of the tools is illustrated through a case study by analysing a suite of nickel processing technology routes. The analysis reveals that current generation of nickel processing technologies do possess real potential to emerge as sustainability champions in integrated processing of nickel ores and concentrates, if they are designed, engineered, and operated for sustainability and adapted effectively to site specific constraints and opportunities. The paper will address data gaps and uncertainties regarding the impact of scaling up of pilot-plant performance, and provides strategies to overcome them.

Jan 1, 2006

This paper provides a brief fundamental insight regarding the fabric media concept for liquor filtration. The subject matter will be of interest to metallurgists and engineers with professional responsibility for world class design of solid liquid separation processes and efficient lowest cost operation of existing mineral process plant. Avocet Mining commissioned the worldÆs first mineral liquor clarification process incorporating a fabric media liquor filter at their Lanut gold mine in Sulawesi, in 2004 with design consulting provided by the Australian company SLS Technology Pty Ltd. Development of the technology continues with applied research focused on selecting textile parameters to apply filtration to a wider range of particle and contaminant types, higher solids concentrations, and different process liquors. Liquor filtration with the Fabric Media technology offers an array of attractive benefits. For Avocet Mining, filtration of pregnant liquor directly from the heap leach pad has enabled removal of the sediment pond and sand filters from the traditional process flow sheet, thus providing significant cost and installation time savings. Avocet Mining has recently expressed confidence in the technology indicating selection preference of the technology for the expansion at Lanut and for a new project. The application design window for the Fabric Media concept is extremely flexible with the technology now successfully applied to many different liquor chemistries and application objectives around the world. Potential cost savings for solid liquid separation process plant, such as counter current decantation circuits, clarifier vessels and thickener tanks can be calculated from laboratory measurements or pilot plant demonstrations.

Jan 1, 2008

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

The recent trend of installing flotation cells with volumes as large as 200 m3 in concentrators is driven mainly by economic considerations such as lower capital, operating and maintenance costs. Despite the economic advantages, the metallurgical benefits from these large cells have not yet been fully realised by the industry. This is mainly due to the lack of understanding of cell operation, viz cell mixing and hydrodynamics, gas dispersion and froth transportation behaviour in large cells. There is still no rational basis for selecting optimum cell operating conditions and down-the-bank operating profiles. The relationship between cell operating conditions and metallurgy is not well established. This has resulted in poor utilisation of cell capacity in many operations. The present trend of installation of fewer cells in a bank requires each cell to be operated very efficiently. Optimisation of cell operation provides an opportunity for significant metallurgical improvements in a flotation circuit with minimal capital expenditure. Extensive work on optimising of cell performance has been carried out at various Teck Cominco operations in Canada, Peru and USA. Three different levels were involved in this work. The first level was aimed at identification of cell operating conditions for optimum mixing and hydrodynamics, gas dispersion, entrainment and froth flow behaviour in individual cells. The objective of the second level was to identify the optimum bank operating profile for cells down the bank in a circuit. The third level then focused on controlling these cell operating conditions and bank operating profiles for tighter control of concentrate grade and recovery for optimum bank metallurgy. This paper presents some of the major findings at all three levels and demonstrates the importance of each level in optimising the performance of flotation banks installed with large cells.

Jan 1, 2005