Search Documents

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent ?looseness? to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-by-minute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

May 1, 2004

By P. L. Richard

An open pit a mine can be thought of as a business unit, with capital, operating and maintenance costs that exceed those of many large business enterprises. Truck-and-shovel operations have an inherent “looseness” to them, unlike manufacturing or processing operations where production components are tightly coupled (through conveyors, material flow in pipes, assembly lines, and so on). Effective monitoring and control of truck-and-shovel operations requires a combination of both information systems and performance management. Production monitoring systems can impact operations at three levels: minute-byminute decisions during the shift, procedures, and policies. The technology of production monitoring ranges from real-time data collection to manual entry of time card data into a computer. Time card information is too coarse to effectively manage a multi-million dollar fleet of mobile equipment, so a higher level of production monitoring is required. People issues affect whether the implementation will be a success or a disappointment. Considerations that affect the people issues are discussed, including common obstacles, and key success factors. A balanced scorecard approach must be used, since uni-dimensional measures of performance like tons produced give no indication of whether the production was achieved at the expense of another factor.

Jan 1, 2004

By Nicole Peter

When introducing digital training technology a practical approach helps address cultural concerns.  Solutions to help create acceptance are discussed.  Resistance to change may be deeply rooted in traditional mine training personnel.  Traditional training staff members may consider themselves less digitally-savvy and resist technological methods available to them. A transitional approach intended to help mitigate or resolve resistance is presented as a continuous improvement pathway toward full adoption.  This presentation contends every mine should welcome the benefit of a digitally connected critical enabler.  The adoption of a digitally savvy learning centre is often viewed a disrupter to existing practice.  Given a commitment-driven learning centre model, technology offers the opportunity to transition from a compliance-based training model to one of competence.  Learning and Development practitioners should welcome the latest advances in neuroscience, Bloom’s taxonomy of learning model, and principles which guide mine safety training as outlined by the Lowell Institute for Mineral Resources at the University of Arizona. By employing digital applications to include animation, game-based simulations and immersive Virtual Reality (VR) these technologies create a viable digitally-savvy learning centre. We will outline the ingredients of a digitally enabled, or VR, Learning Centre to offer some observed benefits, successes, and potential short-comings. Much excitement in the industry surrounds implementation of simulation and/or VR headset training.  Given fair consideration of these as a ‘fit-for-purpose’ solution we examine the paradigm shift required to create real results for on-the-job learning.  Interim steps may be needed to meet the cultural transformation.   Simpler forms of VR, in the form of 3D models and VR environments as displayed on a large interactive touch screen, can serve to bridge this challenge and address a group learning environment. Features of the interactive 3D technology and ease of adoption are presented.  Usage of the touch screen is similar to that of a smart phone. It may be implemented as an obvious transitional tool.  To help describe merits of the interactive touch screen the presentation points out these sample underground and surface mine training applications. There are 3-D simulations such as ventilation, emergency response, support installation, and mine cycle and activity scheduling programs. These applications offer the ability to conduct entry examinations, complete digital pre-use checklists, and perform planned task observations in the virtual world of work. The tool may be used to teach the flow of hydraulics and do fault-finding on machinery such as loaders and dump trucks. Learners may navigate in a virtual mining environment to identify hazards, detect and assess abnormal ground conditions, address poor design features, and alleviate traffic constraints. It is possible to use connected physical controls to navigate machinery in the virtual environment. We conclude the presentation with a “compare and contrast” approach to cite potential cultural benefits by adopting a transitional method. 

May 4, 2025

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By Stanley G. Butcher

"The methods generally applied to predict performance and financially evaluate beneficiation options are reviewed.Typical costs f or a western Canadian thermal coal operation are examined. Preparation-from truck dump to loadout-frequently amounts 10 over a quarter of total minesite costs. Failure to achieve projected yield-whether caused by mine or plant problems-s-substantially increases production costs because more coal has 10 he mined to meet a specific market demand. Problem identification by mass/ash balances is recommended.Thorough characterization of the coal and associated waste materials and more reliable prediction of beneficiation process performance are therefore essential to determine a project 's financial viability.IntroductionWestern Canadian coal prep a ration plant capacity is partway through a massive expansion program . In 198 1 potential product ion was 14 million tonnes, by 1985 it will be 26 million tonnes per year. Only two years ago the industry was concerned whether it could sustain this rate of growth to meet market demands : now with diminished market demand and lower coal prices being offered by our international competitors there are doubts whether t his potential will be fully employed , even by 1990.One direct consequence o f the occurrence of a variety of coals in a stunningly beautiful but complex geo logical setting such as the Rocky Mountains and their Foothills is that each project is unique. Coal is a low value per tonne product. To supply distant markets from geographically isolated deposit s necessitates expensive , dedicated , infrastructure . T o be profitable these operations must achieve eve ry advantage of the economy of scale.Each of the mi ne complexes commissioned in the 1970s experienced severe problems in the area o f co a l preparation . Most bought their way out , paying for major plant modifications by increasing the scale of their total operation . The current market recession may not allow new operations this route to profitability.The objective of this paper is to illustrate the economic impact of coal preparation problems on the profitability o f the total minesite operation and thus provide a sound basis for decision making process."

Jan 1, 1985

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By M. Kumral, E. Dilhuydy, B. Ozdemir

"In-pit crushing and conveyor (IPCC) systems have become increasingly popular in the mining industry as an alternative to truck-and-shovel systems. Deciding whether to haul waste rock by truck or IPCC represents an important gap to be investigated in semi-mobile IPCC systems. A cost analysis is presented to evaluate the feasibility of crushing and conveying waste material in IPCC systems, along with sensitivity and risk assessments through Monte Carlo simulation. Although the capital expenditure is higher, results showed waste crushing will be feasible in deep pits and over long mine life and haul distances.RÉSUMÉ La popularité des systèmes de concassage et de transport dans la fosse minière (IPCC, de l’anglais In-pit crushing and conveyor) n’a cessé de croître dans l’industrie minière ; ils constituent en effet une option intéressante de remplacement des systèmes par camions et pelles mécaniques. Le choix entre le transport des stériles par camions ou par IPCC est encore difficile à faire et devra faire l’objet d’une étude approfondie au niveau des systèmes d’IPCC semi-mobiles. Une analyse des coûts est présentée pour évaluer la faisabilité du concassage et du transport des stériles par les systèmes d’IPCC, de même que des évaluations de la sensibilité et des risques par le biais de la simulation de Monte Carlo. Si les dépenses en immobilisations s’avèrent être plus élevées, les résultats ont cependant montré que le concassage des stériles sera envisageable dans des fosses profondes ainsi que sur une longue durée de vie et de longues distances de transport. INTRODUCTIONThe mining industry is currently facing many challenges such as low commodity prices, increasing environmental concerns and regulations, lower grades, deeper mines, and greater waste-rock quantities. As a result, the profitability of mining operations has decreased, with many mines stopping or suspending operations, and many new projects being postponed. Mining companies have therefore focused on improvements and innovations to increase the cost effectiveness of operations, for example, increasing production capacity to take advantage of the economies of scale (Crowson, 2003) and decreasing the unit operation cost. Changes in production capacity force mining companies to evaluate alternative material handling systems.During the past few decades and within material handling systems, significant improvements have been made to truck performance and capacity. Consequently, operating expenditures (OPEX) associated with fuel and maintenance have risen swiftly. In a mining operation, truck hauling systems now represent 40–50% of the capital cost and approximately 45% of the OPEX (Tutton & Streck, 2009). Additionally, material transportation costs are expected to increase due to longer haul distances arising from deeper and larger mines (Fleet et al., 2015). Finally, large fluctuations in fuel prices result in high risks associated with truck OPEX. According to the United States Energy Information Administration (2015), the cost of crude oil—the largest component of the retail price of diesel fuel—increased from US$24.31/barrel in 1986 to US$46.92/barrel in 2016, peaking at US$151.72/barrel in 2008 (Macrotrends, 2016)."

Jan 1, 2017

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By Sarah Bélair, Denis Beltrami, Valérie Weigel

"Mabounié is a polymetallic deposit in Gabon containing niobium (1.2%), tantalum (0.03%), rare earth elements (REE) (1.4%) and uranium (0.03%) that are mostly carried by Pyrochlore minerals. Classical route for niobium recovery is a pyrometallurgical process that consists in pyrochlore flotation, dephosphorization of the niobium concentrate and aluminothermy to obtain ferro-niobium. Pyrochlore concentrates can also be treated by a hydrometallurgical process with a mixture of sulfuric and hydrofluoric acid leaching followed by solvent extraction to separate niobium and tantalum. However, the first process does not allow recovering REE and the second one is not environmentally friendly because of the use of HF.ERAMET is looking for new opportunities on strategic metals market and has recently developed a hydrometallurgical process for the recovery of all these metals based on a sulfuric acid treatment of the ore. After solubilisation of the valuable elements, niobium / tantalum are precipitated as a concentrate (12% w/w Nb and 0.3% w/w Ta) while REE (2.7 g L-1) and uranium (90 mg L-1) remain in solution. Nearly 90% of REE are recovered from the solution by conventional REE double salt precipitation [NaREE(SO4)2.xH2O) method but some REE still remain in solution as this method does not allow to quantitatively recover medium (Sm, Eu, Gd, Tb, Dy) and heavy (Ho, Er, Tm, Yb, Lu, Y) rare earth elements. From the different process routes studied (solvent extraction, precipitation, ionic exchange etc.), an innovative method has been developed and patented to recover REE residual concentration in solution. This is based on an aluminum removal step followed by precipitation of REE as REE phosphate concentrate (REEPO4) by phosphate addition into solution. The phosphate concentrate is then purified according to the conventional monazite treatment, i.e. caustic conversion and REE solubilisation in acidic media."

Jan 1, 2016

By P. Cain, B. Martens

"Grande Cache Coal (GCC), an investor-owned Alberta company, is in the final stages of the regulatory process leading to the resumption of coal mining in the Smoky River Coal Field of Alberta. Although many opportunities for low-cost, high-yield mining remained on the property, GCC opted for a long-term production plan that ensures stability for the local economy, sustainable use of the resources in the area, environmental responsibility and a satisfactory return for its investors.GCC entered the Alberta coal approval process in late 2000 with a public disclosure document. In October 2001, GCC formally submitted an application for mining approval and an environmental impact assessment (EIA) to the government and the public. The application covered the proposed Grande Cache Coal project, which includes the No. 7 underground mine, No. 8 surface mine and coal processing operations. The EIA provided a comprehensive investigation of environmental sensitivities in the project area, matched with environmental protection programs. The project is based on commencement of operations in late 2002. GCC’s plans are founded on a commitment to sustainable development and has framed this commitment in the context of a long-range mine development plan that will sustain the community of Grande Cache over the next 25 years. The Grande Cache coalfields offer extensive coal reserves and opportunities, for both surface and underground mining. Combining highly productive U.S.-style room and- pillar underground mining methods and conventional truck-and-shovel open pit mining, GCC’s approach to sustainable development encompasses community involvement and reclamation of mine sites to productive land uses after mining."

Jan 1, 2002

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By Robert B. Parsons

"Canada's mining industry has reason to celebrate the federal government's budget which was tabled on February 26, 1986. The budget contains an important proposal to improve the flowthrough share rules by effectively eliminating the investor's liability to third parties. This proposed rule change and other important budget proposals are the subject of this month's edition of Tax Notes. IntroductionWhile Finance Minister Michael Wilson's February 26, 1986 budget received a mixed reaction from business and labour leaders, the budget was mainly ""good news"" for the mining industry. A long-standing bugaboo in the flow-through share rules will be cleared up, a permanent set of rules will be installed for the tax treatment of Northern allowances, and limited partnerships will apparently be able to continue to serve a useful role in financing exploration programs. Flow-Through SharesThe present rules which apply to an investment in flow-through shares are structured in such a way that the relevant Canadian exploration expense (""CEE"") must be incurred by the investor, and not by the issuing corporation. Obviously, in the case of most flow-through share issues, this requirement that the investor incur the CEE poses a practical problem-the investor typically does not have the expertise or organization to incur the CEE. As a result, an integral part of most flowthrough arrangements is an agreement whereby the investor appoints another party (usually the issuing corporation) as his agent to spend the flow-through funds on CEE on his behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, nevertheless the legal structure is such that the investor is the ""principal"" who is incurring the CEE. As such, the investor is legally responsible for any third-party claims with respect to the exploration program. Third-party liability might arise, for example, in the case of property damage, personal injury, environmental infractions, and so on."

Jan 1, 1986

By Charles B. Newmarch

Abstract In the course of coal studies undertaken by the B.C. Department of Mines in southeastern British Columbia, special attention was directed to problems of coal seam correlation. Methods that had been used successfully in other coalfields were found, in the Crowsnest area, to have a restricted use or furnished only additional evidence that might prove helpful when used in conjunction with other criteria. A correlation technique involving semi-quantitative spectrographic analyses of coal ashes was developed. Elements detected in the ash include Si, B, P, Fe, Mg, Mn, Pb, Ti, Cr, Ga, Ca, Al, Ge, Ba, Mo, V, Ag, ?y;b, Na, Zn, Zr, Ni, Sr, Cu, K. Of these, the elements found to be most useful in correlation were Na, Ba, Si, V, and Mg. The element Na was invariably detected in the ash from one of the seams but was not found in samples taken from any of the others. In all of the four seams sampled statistically, significant differences in the amount of certain trace elements were noted. When the values obtained for these trace elements were portrayed in the form of histograms, the resulting diagrams had a characteristic shape for each seam. The diagrams provided a basis for seam identification within the limited area (8,000 feet by 4,000 feet) that was investigated. Introduction During the field seasons of 1946, 1947, and 1948 the British Columbia Department of Mines undertook a geological investigation of the coal measures of southeastern B.C. As field work progressed in the Crowsnest area it was found that, within the Kootenay formation, which contains all the commercial seams of the region, the coal beds are the most persistent stratigraphic units. Because of relatively rapid changes in ?both the thickness of the seams and the interval between seams, difficulty has invariably been experienced in attempts at correlation. Even short-range correlati0ns by able geologists who have worked in the Crowsnest coal basin have been questioned by the operating companies. It was apparent, therefore, that a more dependable correlation technique was needed so that stratigraphic and structural studies could be of greatest value. This paper presents, firstly, a summary of the results obtained in attempted correlations using methods that have been found effective in other coalfields. Secondly, a method based on semi-quantitative spectrographic analysis of coal ash is described and the apparently promising results are discussed.

Jan 1, 1950

By A. M. Salomon de Friedberg

With respect to impurities, HBM&S' copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

By A. M. Salomon de Friedberg

"With respect to impurities, HBM&S' copper smelter, located in Flin Ron, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Ron is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.IntroductionHudson Bay Mining & Smelting Co. Ltd. (HBM&s), has been operating its metallurgical complex located in Flin Flon, Manitoba, since 1930. The smelter and zinc plant were originally separate entities with respect to production. The smelting operation consisted of traditional multiple-hearth roasters, a reverberatory furnace and Peirce-Smith converters. The zinc plant also utilized multiple hearth roasters and then followed with sulphuric acid leaching, purification and electrowinning. The zinc plant also recovered cadmium from a separate purification/electrowinning circuit.The two plants operated essentially independently of each other until rising zinc levels in the copper concentrate and large stockpiles of zinc-rich leach residues prompted the construction of the fuming plant in 1949. The smelter used pulverized coal to reduce zinc oxide present in the reverb slag and then captured the resulting zinc bearing fume in the fuming plant baghouse. The fume was sent to a separate ""oxide roaster"" in the zinc plant where it was first roasted to remove halogens and then leached to recover the contained zinc. This oxide fume became a major source of feed to the zinc plant accounting for roughly one quarter of the total zinc production. Furthermore, through the smelter's treatment of sulphide leach residue, both copper and zinc recoveries were improved for the over-all complex."

Jan 1, 1993