Search Documents

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By Edouard Asselin, Tasawar Javed

The precipitation of hematite from ferric sulphate - cupric sulphate - lithium chloride acidic solutions was studied in a batch reactor. The effect of several variables on the extent of hematite precipitation as well as on its crystallinity and purity was investigated. The variables studied include: initial ferric concentration (1.5 - 30 g/L), retention time (0 - 12 h), initial sulphuric acid concentration (0 - 30 g/L), temperature (150 - 220 °C) and chloride concentration (0 - 25 g/L). The results show that hematite is preferentially precipitated at lower initial iron concentrations. Longer retention times increased the fraction of hematite in the precipitates but did not affect its crystallinity to a significant extent. On the other hand, higher temperatures increased the purity and crystallinity of the hematite. At lower acid concentrations hematite and goethite were precipitated. However, only hematite was precipitated when the initial acid concentration was > 12.5 g/L. Better crystalline hematite was formed at lower acidities. Increasing chloride concentration increased the amount of hematite and decreased the amount of iron sulphate hydroxide phases, but did not affect the crystallinity of the hematite.

Jan 1, 2015

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By D. G. Tisdale, W. Curlook, J. M. Toguri

"In this study, the vapour phase reduction of titanium tetrachloride conforms to the traditional Kroll chemistry, but employs argon as an inert carrier gas and requires a higher reaction temperature of 1150°C to 1250°C. A vapour phase reaction is advantageous because titanium is the only condensed phase present, and the metal can be collected free of magnesium or magnesium chloride, in marked contrast to the titanium sponge produced by the conventional Kroll process. The yield of metallic titanium from the reaction was determined as magnesium additions ranged from 36% to 168% of the stoichiometric requirement. Yields of over 99% were obtained when an excess of magnesium was present. Although the collection efficiency was low, metallic titanium was collected at the reaction site, where all other species were present as vapours. Magnesium and chlorine concentrations in the collected titanium were less than 0.3%.IntroductionA proposed method (Curlook, 1987) for titanium production has been investigated as an alternative to the conventional Kroll process (Kroll, 1940). The advantages of the new process include a simplified means of recovering the product metal, and a potential for lower overall energy consumption and greater product purity. A higher reaction temperature for the reduction of titanium tetrachloride results in a vapour phase reaction, rather than the conventional liquid phase reaction. This is the major conceptual difference between the proposed and the established (Kroll) processes.This study focussed on optimization of the process chemistry and briefly examined the issue of product deposition and collection. The reduction of titanium tetrachloride with magnesium, to produce metallic titanium and gaseous magnesium chloride:"

Jan 1, 1997

"Mining with blast holes drilled upwards may be done to recover sill pillars, or for economic reasons when the distance between the levels is relatively large. If the rock is sufficiently competent to accommodate large stope size, the distance between sublevels could be increased to as much as drilling accuracy allows. The same drill drift can be used for the drilling of both down holes and up holes. In the case of down holes, the initial opening of the stope (drop raise) is not as much a problem as for the inverse drop raise for mining with up holes. This is because, with a drop raise, a lot of space is available at the toe for the blasted rock to expand. In addition, the raise can be blasted in many shots, thus allowing smaller blasts each time. Inverse drop raises are generally much more difficult to blast because of the limited space for muck flow, and must, therefore, be taken down in a single blast, requiring special considerations in order to ensure a success. A case study of a 29 m (95 ft) inverse drop raise successfully blasted in a single shot at Heath Steele Mines is described. The paper covers technical considerations such as drilling accuracy, hole deviation survey, delay extension and protection, initiation methods and initiation sequence. Finally, a novel method for creating the initial opening called ’slot drilling’ is presented. This method, inspired from LKAB in Sweden, consists of drilling a row of interconnected holes using a special guide mounted on a regular production drill hammer.With a case study of blasting an inverse drop raise of 29 m (95 ft) in one blast, this paper further discusses some technical issues that are critical for the development of inverse drop raises. A novel method for creating the initial opening with a slot of interconnected holes is also presented with the experience acquired at different mine sites across the Noranda group."

Jan 1, 2000

By Anoop Sattineni

Over the past decade the use of BIM in the AEC industry has grown several fold and with it the number of standards available for implementing BIM. The ?National BIM Standard? by buildSmart Alliance, the ?Contractor Guide to BIM? by the Associated General Contractors of America, the ?BIM Project Execution Planning Guide and Templates? from Penn State University, the ?BIM Roadmap? by the US Army Corps of Engineers are some of the several BIM guidelines that are currently available to the AEC industry practitioners. Some of these guidelines are as comprehensive as defining BIM and the associated taxonomy while others are meant to be used on an individual project basis. From a contractor?s perspective one of the key benefits of using BIM is for the purpose of collision detection and coordination. This research has found that currently available guidelines do not address these issues adequately. For instance, the currently available guidelines do not allow the subcontractor to quickly communicate issues such as naming conventions and color schemes within the model, to the general contractor. Consequently general contractors and sub-contractors find themselves making changes to their BIM deliverables based on each other?s abilities and levels of adoption, apart from reason?s stemming from use of different software platforms. This paper describes how a group of contractors and subcontractors from Atlanta and Birmingham in the United States came together to create and adopt a ?Coordination Guidelines for Virtual Design and Construction?. These guidelines were specifically created with the purpose of streamlining the construction coordination process using BIM. This paper describes how the guidelines created differ from other guidelines currently available in the industry.

Aug 1, 2013

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn&apos;t any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn&apos;t any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By William Petruk

Image analysis studies were performed on mill products from pilot-plant and laboratory tests that had been conducted to determine the effect of grinding media on the selective flotation of two zinc-lead-copper ores. It was found that, when the ores had been ground to the same degree of fineness with flint pebbles, ceramic pebbles or ore fragments (autogenous grinding) as with steel balls, there generally was increased sphalerite, chalcopyrite and galena liberation in the flotation feeds, depending on the textures of the minerals. The increased sphalerite liberation fully accounted for the improved zinc recoveries that were obtained when steel balls were replaced by either pebbles or ore fragments. The increased chalcopyrite and galena liberation accounted for part of the changed technical efficiency of concentration, but other factors, probably changes in oxidation and reduction of iron and in consumption of oxygen, also contributed.

Jan 1, 1977

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

By M. A. Creaney

"The Construction Group is responsible for the construction of all of Placer Dome’s major projects and contributes to the development of most major feasibility studies. This group includes an international collection of Placer Dome people who have built mines in Papua New Guinea, Australia, Chile, the United States and Canada. This paper outlines the changing role of the Construction Group from the early days of single projects to today, when several projects are in various phases from feasibility to construction. The projects’ total annual budgets have from time to time exceeded one billion dollars. IntroductionAs the competition increases globally between the major gold mining companies, the impetus continues to build mines at the lowest cost with the shortest construction schedule. Placer Dome has more than met that challenge by building mines around the world at a pace that was not contemplated 15 or 20 years ago. Since 1960, Placer Dome has built 30 mines and expansions at a cost of nearly 4.5 billion dollars.In the last six years alone, Placer Dome has built 14 mines and expansions, worth 2.6 billion dollars. The company’s success is due primarily to Experience, Innovation, People and Standards.The diversity between projects, let alone the pace, has been a challenge. Placer Dome has built mines around the world in a variety of extreme climates and distinctive cultures. The construction experience gained from these projects has allowed Placer Dome to develop an extensive knowledge and data base making it easier to “fast track” projects.Through the years Placer Dome has developed a human resource base. It now has an experienced and adaptable core team of people able to set up construction projects and build mines anywhere in the world. By developing standards and systems to support the projects they can act as soon as a new project is approved, and complete the projects quickly and effectively. The result is that Placer Dome now has the construction expertise to build its own mines, giving them the competitive advantage that allows them to design and construct a mine in the least time at the lowest capital cost. This was demonstrated in March 1997 with the completion of the construction of two new mines in 12 months."

Jan 1, 1998

By Art Hamilton

Abstract -The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeformed volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically underlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide con­ tent relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.310Jo Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By W. T. Sampson

Introduction The Kirkland Lake (Ontario) property of Wright-Hargreaves Mines, Limited, - consists of four claims. The two main shear zones or &apos;breaks&apos; of the Kirkland Lake camp extend through three of these claims, for a distance of approximately 3,500 feet. These claims are on the northeast side of the original lake. The water in this section of the lake has now been replaced with mill tailings. The degree of success of any completed undertaking, especially in the mining industry, reflects the personnel involved. I state with pleasure that the successful deepening of No. 5 winze from 6,400 feet to 7,272 feet was largely due to the co-operation and skilled workmanship of Shaft Captain J. Myelde and his efficient &apos;leaders&apos;. This winze was sunk at a time when it was most difficult to obtain experienced shaftmen, with the result that the crews did not wholly consist of experienced men (although their desire to learn shaft sinking soon gave good results). This condition added greatly to the responsibilities and duties of those in charge, whose first consideration was for the safety of those engaged in the work, and I take great pride in recording that the entire sinking programme was completed without a lost-time accident. Location of Winze Due to the information obtained through deep diamond-drill holes collared below the 6,000-foot level being of sufficient importance to warrant further exploration, it was decided to deepen the existing No. 5 winze rather than sink another winze. This decision meant that the sinking must be co-ordinated with and proceed simultaneously with operations in the winze, where mining was being carried on between the 3,900-foot and 5,100-foot horizons, inclusive.

Jan 1, 1948

By M. J. Gole, R. E. T. Hill, S. J. Barnes

"The Agnew (also known as the Perseverance) nickel deposit and its northern extension, the Rocky&apos;s Reward deposit, form one of the world&apos;s largest accumulations of nickel sulphides hosted by komatiites. Agnew was previously classified as an ""intrusive dunite-associated"" deposit . It has now been shown that the sulphides are hosted by komatiite flows which underlie an adcumulate-textured dunite body that crystallized in a large lava channel.The rocks of the mine area have been subjected to a metamorphic temperature of550°C and pressure of up to 3 kb. The komatiites have mostly been reconstituted to olivine-amphibole chlorite assemblages. There is a zoned sequence of enstatite-, anthophylite-, talc- and antigorite-bearing assemblages inwards from the western margin of the ultramatic reflecting variations in the CO/HP ratio of metamorphic fluids.Facing directions are determined from variations in the proportions of metamorphic minerals and in rock compositions which reflect asymmetric layering in the flows . Olivine-sulphides matrix ore is hosted in a single 50 m thick, east-facing flow that is overlain by flows containing massive sulphides. Much of the massive sulphide has been physically remobilized into fold noses, faults and shear zones. Chemical diffusion of ore components has upgraded a sulphide-rich metasedimentary unit where it is in structural contact with massive ore.To the north, the mineralized flow sequence is separated from a stratigraphically higher komatiite sequence, the Perseverance ultramafic complex, by approximately 150 m of felsic meta volcanic and meta sedimentary rocks. Southward, the Perseverance ultramafic grades laterally into an olivine adcumulate body and its lower contact cuts progressively down stratigraphy until it lies directly on top of olivine-sulphide ore of the mineralized flow sequence. This discordant contact is interpreted as the base of a thermal erosion channel formed by a voluminous komatiite lava flow. This contact greatly influenced later deformation of the mineralized flow sequence."

Jan 1, 1989

By I. A. Tinto

"Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers.HistoryThe Iron Ore Company of Canada commenced work in the area in 19 4 9' however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.The mining facilities, crushing plant, and concentrator were in operation by the early part of 1962. In the summer of 1961, a decision was made to build a pelletizing plant adjacent to the concentrator. This plant was designed, erected and placed in operation during 1962 and the first half of 1963. Since the completion of the pelletizing plant, additional expansions to both the pellet plant and concentrator have taken place in 1967 and 1973. Today, the Carol Project has the capacity to produce 20 million tonnes of concentrate from which 10.5 million tonnes of pellets can be produced.The period 1980-85 spans a period of energy crisis, world-wide recession, and a consequent re-structuring of the North American steel industry as it struggles to survive in an arena of excess world steel making capacity, government subsidized industries, and the increasing competition from overseas and from developing countries.The media headlines over the past few years echo the woes of the industry and the strategy plans for survival of the fittest. Today's buzz words are foreign competition, steel import quotas, joint ventures, employee participation, work rules, quality, productivity, and state of the art technology."

Jan 1, 1986

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996