Search Documents

By J. E. Udd, S. Bharti

"ABSTRACTMonitoring of stability conditions in underground mines permits management to assess the response of the rock mass to mining strategies. Monitoring of movements, if sufficiently early, may also permit operators either to avert potential failures or to develop alternative approaches to extraction.The Falconbridge organization has been a leader both in the uses of rock mass stability monitoring techniques and in the development of instrumentation.In this paper, the authors review the Falconbridge approaches to monitoring, and present case history examples to illustrate the application of the various instruments used.RESUMELa surveillance des conditions de stabilité dans les mines souter-raines permet aux chefs d'enterprises d'évaluer les réactions de la masse rocheuse aux méthodes d'extraction minière. Si le contrôle des mouvements du terrain est effectué assez tot, l'exploitant pourra prendre les mesures qui s'imposent, soit pour éviter les détériorations possibles ou pour mettre au point de nouvelles méthodes d'extraction.Le groupe de la Falconbridge a ére le premier a utiliser des techniques de vérification des conditions de stabilité de la masse rocheuse et a mettre au point l'appareillage requis.Ce document présente une revue des méthodes employées par la Falconbridge pour assurer la surveillance active de la stabilité de la masse rocheuse et illustre au moyen de cas concrets la manière d'utiliser les divers appareils."

Jan 1, 1987

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By K. B. Chaudhurl

The thermodynamics of the reactions taking place are examined with the aid of equilibrium diagrams for the Pb-O-S system. Based on investigations of chemical, mineralogical and differential-thermo analyses of intermediate products of different desulphuration degrees, an attempt is made to explain the mechanisms of the reactions in the smelting shaft of the KIVCET furnace. The differences between this and other direct lead smelting processes are demonstrated by these thermodynamic and kinetic considerations. Proceeding from these results, the practicability of direct lead smelting processes is discussed with reference to the composition of the primary feed materials to be processed. This comparison also considers the behaviour of minor metals, the products obtained and their characteristics in respect to further treatment. For assessing the operating costs, the over-all energy consumption is considered taking into account various price relations between electric energy and fuels/reductants. Based on the peculiarities of the various processes, an attempt is made to compare the necessary means of meeting the pollution control requirements. The paper concludes with reference to the criteria and problems involved in comparable evaluations.

Jan 1, 1978

By Michael Moser, Brighty Dutta, David Dreisinger

"Molybdenum is widely used in the industries as an alloying element in the manufacture of steels and super alloys. The widespread use of the element encourages a growing need to develop extraction processes for recovery from both primary and secondary sources. The Solvay Group has developed a solvent extraction reagent named CYANEX®600 for the recovery of molybdenum from acidic solutions originating from both low grade (e.g. copper solvent extraction raffinates, smelter dusts and slags) and high grade (molybdenite) molybdenum sources. CYANEX®600 is a purified form of CYANEX®272 with the active component bis(2,4,4- trimethylpentyl)phosphinic acid. The extraction behavior of CYANEX®600 towards molybdenum in sulphuric acid medium was evaluated. The uptake of molybdenum increased with the increase in concentration of CYANEX®600. The approximate stoichiometry of the extracted complex was: Mo: CYANEX®600 = 1:2. Efficient back-extraction could be achieved with 0.1 M disodium EDTA and 0.1 M (NH4)2CO3, thus providing the option of recyclability of the extractant. The detailed back-extraction studies are currently under progress to find out the possible option for complete transfer of Mo(VI) to the aqueous phase so that high purity Mo salts could be precipitated from the molybdate solutions.INTRODUCTION Molybdenum (Mo) is one of the world’s valuable metals and is highly sought after by researchers due to its versatile mechanical, thermal, chemical properties. Swedish scientist Carl Wilhelm Scheele demonstrated molybdenite to be a mineral sulfide in 1778. Peter Hjelm successfully isolated dark metal powder from the mineral sulphide and named it as ‘Molybdenum’ in 1782 (Gupta, 1992). Molybdenum is a refractory metal of silver gray appearance and is an important alloying element used in the manufacture of steels and super alloys. Molybdenum compounds are widely used in formulation of catalysts (Gupta, 1992). Molybdenum occurs in nature only in chemical combination with other elements. Several molybdenum bearing minerals have been identified, but the only one of commercial significance is molybdenite (MoS2). As molybdenum is a strategic metal for the industrial sector, its widespread use acts as a factor for depletion of the natural resources. Hence, there is growing need to develop extraction procedures for its recovery from both primary and secondary sources. United States, China, Chile, Canada, Peru, and Mexico are listed as the main producers by the U.S. Geological Survey, 2016 (U.S. Geological Survey, Mineral Commodity Summaries, January 2016)."

Jan 1, 2017

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By D. A. Temple, G. O. John

Until recently, the approach to the problem of treating complex ores bas been to produce, insofar as is possible, mono-metal concentrates which are treated in traditional zinc, lead and copper smelting circuits, with the residues and by-products from some of these circuits being retreated for the recovery of contained values either by a separate residue treatment process or along with the primary feed to the appropriate circuit. The continued development of the Imperial Smelting Process, with its ability to treat poly-metal concentrates, calls for a re-examination of the traditional approach to this problem, and this the paper attempts to do. A survey of recent progress in the technical development of the process is made and a summary of current operational performance is included.

Jan 1, 1971

By C. G. McLaughlan

The Noranda concentrator was placed in operation in October, 1928, and the object of this paper is to outline operations during the twelve months which have elapsed since that time. The ores milled are massive sulphides carrying copper and gold, and, in certain cases, zinc. These ores have a specific gravity of about 3.8. The average assay of the copper-gold ore so far treated has been 2.0 - 3.5 percent Cu; 0.10 - 0.20 oz. Au; 40 - 51 percent Fe; and 6 - 15 percent SiO2. In this ore the copper occurs almost entirely as chalcopyrite, and the iron which is not combined with the copper is present mainly as pyrite and pyrrhotite. ?some iron is also combined with the silica, the ratio being about 1 to 4, and a small percentage is present as magnetite. The occurrence of the gold has been shown by microscopic work carried out by Prof. L. C. Graton, of Harvard University, to be very variable. Some of it is free, and is included within the base-metal sulphides or occurs at their boundaries. A similar distribution also holds for a portion of the gold which is combined as a telluride. Little is so far known of the occurrence of the silver other than that some of it may be combined with the gold in the telluride, petzite. The copper-zinc ore contains up to 6 percent copper, and has a very variable zinc content. The copper in such ore is present as chalcopyrite, and the zinc as sphalerite. In starting the mill we had three conditions to face; the first of these was climatic, the second was the lack of skilled flotation operators, and the third was the ore itself." The last of these three proved much more difficult to contend with than the other two combined.

Jan 1, 1930

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By W. G. McBride

INTRODUCTION Preparation of this article, at the request of the Committee on papers, has been undertaken in the hope that it may stir up helpful discussion and constructive criticism. The Canadian mining industry is in the dumps and there is no use trying to deny the fact; nor does it help to say that other industries are in as bad or a worse condition. Let us face the situation honestly and see just how serious it is. The entire financial and industrial world is in a state of depression. The gravity of the case is no doubt exaggerated by contrast with the wave of optimism and false prosperity which pre-ceded it. The prevailing gloom and pessimism are just as irrational as was the former super-optimism. As far as we mining engineers are concerned, the causes are quite beyond our control, and it is the effect upon our own industry which interests us most. This effect is an accumulation of mineral products with consequent depression in price to a point where profits have almost, if not quite, disappeared. Whether this accumulation of stocks is the result of over-production or under-consumption is difficult to say, but it would seem likely that there is a combination of the two. The introduction of selective flotation has brought about a large increase in the production of zinc, a moderate increase in the production of lead, and a comparatively small increase in copper. It has turned relatively small mines into great producers, as in the case of the Sullivan, revived expiring mines like La Cananea, and brought-in new ones like Flin Flon

Jan 1, 1931

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

By Michel L. Bilodeau, Brian W. Mackenzie, Dallas W. Davis

"The paper formulates an evaluation procedure for examining the effects of location on the economics of developing mineral deposits. This methodology is applied to assess locational aspects of Nova Scotia&apos;s competitive position f or mine development relative to other Canadian regions and provinces. The appraisal concerns two representative mine development opportunities, a medium-size open-pit tungsten deposit, and a small underground gold deposit. The influence of regional economic conditions is initially assessed. Then, the consequences of taxation are isolated. Finally, the combined impact of regional and taxation conditions is examined. SettingThe economic potential of mining may be assessed in a number of ways. One approach, increasingly used for both corporate planning and government policy purposes, is to evaluate the competitive position of an actual or potential mineral producer in the international marketplace relative to other suppliers.Such examinations of competitive position vary from cost league comparisons of breakeven costs for operating mines, through the assessment of medium-term costs associated with developing new mine capacity, to long-term evaluations of the economics of mineral supply from the start of exploration. The complexity of the analysis increase s with the scope and timeframe of interest. Many factors are involved. One component of competitive position is the quality of the mineral resources available. Other key factors include existing technology, wage and salary rates, labour productivity, the cost of capital, infra structure requirements, distances from sources of materials supply an d to mineral markets, management attributes, organizational efficiency, government mineral policies (particularly taxation), and inflation and exchange rates. The paper fits within this competitive position framework.The variable economic conditions which exist within Canada have a direct bearing on the viability of mine development and, thereby, on mineral exploration potential. The paper examines locational aspects of Nova Scotia &apos;s competitive position."

Jan 1, 1986

By L. R. Plitt

A series of experiments were carried out in an effort to develop a universally applicable mathematical model of the hydrocyclone classifier. The design and operating variables studied were: cyclone diameter and height, the inlet, vortex finder and apex diameters, the feed pressure and the solids content of the feed slurry. The model consists of four basic equations which express the cut size ( dso), volumetric split between overflow and underflow, volumetric throughput, and sharpness of separation in terms of the operating and design variables. Although empirical, the model is nevertheless in general agreement with fundamentally derived models. The model clearly 1•eveals the effect of the major variables on the operation of a hydrocyclone. Because of its broad data base and the inclusion of all the major variables, the model may be used without experimental data to predict the operation of cyclones over a wide range of different operating conditions. With operating data, the equations may be modified to serve as an operational model.

Jan 1, 1976

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

By B. A. Strathdee

An arsenical ore containing both pyrite and arsenopyrite was heated to a temperature at which decomposition and distillation took place. The condensate consisted of metallic arsenic and arsenic disulphide, although the analysis of the ore showed that volatile arsenic and sulphur were present in proportion to produce a condensate of arsenic trisulphide and sulphur. Distillation tests on the mineral arsenopyrite also produced a condensate of metallic arsenic and arsenic disulphide. This arsenic sulphide gave a distinct x-ray diffraction pattern which was not listed in the A.S.T.M. data file. This same sulphide can be produced by heating a mixture of arsenic and sulphur in vacuo. Its chemical analysis corresponds to As2S2. The dissociation pressures of arsenopyrite and the vapour pressures of arsenic disulphide and arsenic metal were measured, using a quartz "spoon" gauge. The dissociation pressures of arsenopyrite were compared with the published data for the dissociation pressures of pyrite to account

Jan 1, 1961

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000