Search Documents

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By M. L. F. Gameiro

The aim of this study was to check the feasibility of non-dispersive solvent extraction to recover copper from ammoniacal solutions using hollow fibres as contactors. Data of mass transfer using the B3-diketone LIX 54 as extractant was obtained. The influence of tube and shell hydrodynamics on the extraction rate of copper was studied. The overall mass transfer coefficient of copper was calculated from the experimental data by performing steady state material balance. Simultaneous extraction and stripping experiments were carried out using different volume ratios of feed phase to stripping phase. The results obtained showed that practically all the copper content was removed from the ammoniacal feed solutions. The recovery of copper reached nearly 100% in several extraction-stripping experiments.

Jan 1, 2007

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow 'gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"The future of Polish copper mines KGHM Polish Miedz S.A. will be associated with mining at depth. At present, technologically advanced measures are being introduced to minimize the adverse influence of the environmental hazards on people working underground. Polkowice-Sieroszowice mine is the only mine in Poland where mining takes place in copper and salt deposits. On the basis of the current and anticipated methods of ventilation of a selected ore deposits the paper will analynze a number of solutions enabling planned mining of copper ore deposit, while minimizing the impact of natural aerological hazards in working areas. INTRODUCTION The future of copper ore mining, carried out by KGHM Polska Miedz S.A., will be based on mining from continuously greater depths (Butra, 2015). It is forecast that this will be accompanied by an increasing climatic hazard, resulting from an increase in the original temperature of rocks of more than 45°C as well as gas and geodynamic hazards (Soroko, 2015; Andrusikiewicz, 2015). Due to the safety of underground teams, a need arises to develop methods eliminating the adverse impact of the natural hazards, down to a level enabling the mining activity to be carried out on an industrial scale while maintaining favourable economic parameters. Current depths of the copper ore deposit being developed are effectively verifying the technical methods and measures employed to date for eliminating the natural aerological hazards. Amounts of air supplied to mining areas, with lengthy transport routes, are becoming insufficient for miners’ temperature safety, whereas increasing the power of cooling air-conditioning stations for cooling the air undermines the economic legitimacy. However, along with the temperature hazard, a significant problem at the current depths is an increase in gaseous occurrences in the headings’ areas. The concentrations of natural harmful gases found, even with the values below the permissible concentrations, in the case of limited amounts of air and/or low airflow rates, may pose a considerable danger to the workers. The hazards referred to are currently the major factors determining the advance of headings, above all in mining sections, being the outcome of geological structure and depth of lying of a deposit. However, at the current depths of mining minerals from deposits, room-and-pillar mining systems employed also have a decisive impact on the increase in natural aerological hazards."

Jan 1, 2019

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

By H. W. King

"Cryogenic engineering is concerned with components and machines which operate for long periods of time at temperatures within a few degrees of absolute zero. The absence of a ductile-brittle transition is thus the prime component of the specification for a suitable low-temperature alloy. The word "" cryo"" means ""frost-forming"" , and this leads to the second component of the alloy specification, which is resistance to corrosion in humid atmospheres. Further, although most early applications of low-temperature alloys were limited to the storage or transportation of liquified gases, an increasing proportion of alternative energy storage and conversion technologies are being based on the availability of high-field superconducting solenoids. The third basic component of the specification for a low-temperature alloy is thus the absence of a low-temperature ferromagnetic transition.Although the firs t two of these components of the specification can be met by using austenitic stainless steels, many of these supposedly "" non-magnetic"" alloys have been found to undergo martensitic transformations to ferromagnetic phases at very low temperatures. In addition, steels which remain structurally stable may still exhibit other magnetic transitions, e.g. to antiferromagnetic or superparamagnetic states. The successful application of these alloys in cryogenic engineering has thus required an initial basic study of the types of magnetic transition that can occur in such concentrated solid solutions, followed by a more applied study directed at an alloy formulation which will induce beneficial magnetic states at low temperatures."

Jan 1, 1981

By P. O. Parfitt

At the McIntyre mine, there are two distinct operations: a gold mine with narrow veins, mined by cut-and-fill methods, and a copper mine with large, open, long-hole stopes. The application of the Critical Path Method to scheduling work in the copper mine, where it has been used successfully for several years, is de-scribed briefly. This application is relatively simple. Use of C.P.M. has now been extended to the gold mine. To replace the former method of scheduling from bar-charts, a procedure was developed for scheduling automatically. To handle an operation of this size and complexity, a computer was essential. Improved schedules are now being produced, with a saving in time.

Jan 1, 1967

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By Dart Wantland

"AbstractThe scope of geophysics in civil engineering and the nature of exploration geophysics are briefly discussed. Engineering problems amenable to geophysical attack are illustrated by specific examples. The various methods available, accuracy of results, and costs are treated. The possibilities of new uses of geophysical techniques are pointed out.IntroductionTHE SCOPE of geophysics in engineering is different than in oil or mining exploration. In civil engineering, geophysics solves specific problems; as for example, what is the depth to bed-rock along the axis of a proposed dam? The area to be surveyed is of limited extent, and the subsurface information .sought is relatively near the surface. The engineering geophysicist is not called upon to investigate geological basins or extensive mineralized areas or to probe for data to thousands of feet in depth. The geophysical tools employed in the three fields are, however, quite similar; the differences are mainly in the objectives.The Natural Geophysical ExplorationThe terms geophysics and geophysical exploration have been used heretofore and will .be employed in what follows. The question is, therefore, What is geophysical exploration?Geophysical exploration is a line of field work where measurements are made at the ground surface with special instruments to get geological subsurface information. Briefly stated, geophysics is a form of exploration that supplements geological work. It is a blend of physics and geology since physical measurements are made •at the surface of the ground that can be interpreted in terms of subsurface conditions."

Jan 1, 1953

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By E. O. T. Simpson

"IntroductionAS COMPARED with coal mines in the United States, and even with some of those in eastern Canada, the coal mines of western Canada, generally speaking, :have made little progress toward mechanization at the working faces. So far as Vancouver island is concerned, there are three main reasons for this : ( 1 ) in some areas, conditions• easy for hand-loading but unsuitable for mechanical loading make high outputs per man •possible by the former method; (2) faulting of the coal seams in ..some areas precludes long-term planning and the introduction and efficient use of expensive equipment; (3) thinness •and other characteristics of the seams in many areas favour hand-loading.No. 8 MINENo. 8 mine of Canadian Collieries (Dunsmuir), Limited, is located in the Cumberland sub-area of the Comox coalfield on Vancouver island about 90 miles west-northwest of Vancouver. The geological structure of this coalfield has been described by J. D. McKenzie. The seams occur in the Comox formation, a subdivision of the Upper Cretaceous Nanaimo Group. The formation is of near-shore origin and was laid down on an irregular surface of' older rocks. The irregular generally have a northeasterly dip, modified by gentile folds and by a •few large, and a number of smaller, faults.Four seams have been worked in the Cumberland area and all vary in thickness and in the amount and number of interstratified bone and rock •bands."

Jan 1, 1953

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By E. J. Burrough

MR. J. J. McIntyre (International Coal & Coke Company, Ltd., and McGi1livray Creek Coal & Coke Company, Ltd., Coleman, Alta): Mr. Burrough's excellent paper, Metallurgical Coals of the Crowsnest Area, seems especially timely now, when the need for developing iron industries in the west, as well as in the east, is receiving so much attention. His -thorough review of the 'coking' industry is an especially valuable contribution, along with which the following brief remarks on coking in the Crowsnest Pass area of British Columbia and Alberta may be in order. When the Crowsnest Pass line of the Canadian Pacific railway was built there were great expectations for the non-ferrous metal industry; quite a number of smelter's were al-ready in operation in British Columbia and the northwestern United States, and further expansion was confidently expected. The suitability of the medium-volatile coking coals of the Pass for making metallurgical coke had been recognized from the time the fields were first explored. By the time the mines were fairly well developed there was already a market to war-rant the building of coking plants, and a common belief that expansion of the market would require a large coking industry. The first coke production was from plants built by the Crowsnest Pass Coal Company, Ltd., at Fernie, B.C. in 1903, and the International Coal and Coke Company, Ltd., at Coleman, Alberta. These plants were followed by others built by the Crowsnest Pass Coal Company, at Michel, B.C., by West Canadian Collieries, Ltd., at Lille, Alberta, and by Leitch Collieries, Ltd., at Passburg Alberta, and by a plant at Hosmer, B.C.

Jan 1, 1951