Search Documents

By L. K. Mireku

"Abstract - The Halfmile Lake South Deep zone, Bathurst Mining Camp, New Brunswick, was discovered by Noranda Inc. (Exploration) as a result of a 3-D seismic survey in 1998 and the subsequent drilling of ten diamond-drill cores. The deposit consists of massive, breccia, and stockwork Pb-Zn-Cu sulfide minerals, and is hosted by a volcano-sedimentary sequence belonging to the overturned Ordovician Tetagouche Group. Epiclastic rocks and interbedded fine-grained felsic pyroclastic rocks dominate the stratigraphic footwall. Locally, crystal-rich felsic tuffs and subordinate epiclastic rocks comprise the immediate stratigraphic hanging wall. The entire stratigraphic sequence was intruded by quartz-feldspar porphyritic intrusions, and cut by intermediate and basic dikes. The volcanic and sedimentary rocks can be discriminated geochemically using trace element ratios such as Zr/TiO2 and Nb/TiO2, despite intensive alteration and cleavage development. These ratios indicate that four protolith volcanic compositions exist: rhyolite, dacite, andesite, and basalt. The aphyric and feldspar- and quartz-phyric volcanic rocks are dacitic and rhyolitic in composition; epiclastic rocks have trace element ratios consistent with dacitic compositions. Pearce element ratio diagrams, general element ratio diagrams, and petrographic observations demonstrate that the rhyolitic volcanic rocks exhibit evidence of albite, potassium feldspar, and quartz fractionation, dacitic volcanic rocks exhibit little evidence of any fractionation, and epiclastic sedimentary rocks exhibit evidence of quartz sorting only. Hydrothermal alteration is best represented by the presence of phengitic muscovite and daphnitic chlorite. Minor calcite occurs in the stratigraphic hanging wall, deep in the stratigraphic footwall, and in post-mineralization dikes, and thus is not interpreted to be part of the causative hydrothermal event. Element additions and losses during alteration have been used to determine net alteration reactions, and these have been used to identify alteration parameters that are independent of other forms of alteration and fractionation/sorting, and which can be used to guide exploration. These parameters include: a bulk hydrolysis measure, (2Ca+Na+K-2CO2)/Al; a muscovite alteration measure, K/Al; an albite destruction measure, Na/Al; a chlorite alteration measure, (Fe+Mg-S/2)/Al; a chlorite composition measure, (Fe-S/2)/Mg; a sulfidization measure, S/Ti; and a carbonatization measure, CO2/Ti. With the exception of the carbonatization measure, these alteration parameters define a distinct lateral and vertical zone of intense hydrothermal alteration in the stratigraphic footwall of the deposit, and demonstrate that the epiclastic rocks are predominantly chlorite altered, and the volcanic rocks are predominantly muscovite altered. Within the alteration halo, element additions of Fe and H, and element losses of Na are characteristic. Potassium was added to muscovite-altered rocks, but subsequently removed from chlorite-altered rocks. The results from this study demonstrate that metamorphism and deformation have not significantly obscured hydrothermal alteration signatures."

Jan 1, 2006

By K. S. Coley, M. A. Rhamdhani, G. A. Brooks

Interfacial phenomena in high temperature reactions such as between iron alloy and slag is well documented but not fully understood. It is believed that a gradient of oxygen concentration plays an important role to the occurrence of such phenomena. This article describes the results from the continuation of the study of interfacial phenomena between Fe-Al alloy droplets and CaO-SiO2-Al2O3 slag. Materials characterization techniques involving microscopic observations, depth profiling, bulk, point analysis and were carried out. The roles of oxygen as well as other factors that contribute to the interfacial phenomena were evaluated. The results and their implications to steelmaking will be discussed.

Jan 1, 2004

By Jean-Marc Simard, Richard Genest

"La mine Agnico-Eagle, localisée près de Joutel, a été découverte en 1962 par le forage d'anomalies électromagnétiques. Exploitée à partir de 1974, elle a déjà produit près de 30 tonnes d’or à partir de 2 puits, le puits Eagle et le puits Telbel, distants de 1,3 km.Le gisement est situé entre le sommet du complexe volcanique de Joutel, à dominante felsique, et la base de l'ensemble sédimentaire de la rivière Harricana. Ces deux unités ont une extension régionale; elles sont orientées NW-SE avec une polarité NE et des pendages subverticaux. Une faille majeure, la faille Harricana, passe de façon subconcordante au contact de ces deux ensembles.La minéralisation aurifère, de 2 à 5 m d’épaisseur moyenne, est liée a une zone carbonatée, comprise entre des tufs felsiques, argilites et sédiments chimiques (éponte inferieure) et des argilites carbonatées (éponte supérieure). Le minerai est constitué habituellement de 20% de fine pyrite disséminée. L’or est en fines particules associées directement à ces grains de pyrite de texture cataclastique.Deux modelés ont été for mules jusqu' a présent pour expliquer la genèse du gisement: une thèse syngenetique (Barnett et a/.1982) et une thèse épigénétique (Wyman et al. 1986). Cette dernière apparalt comme la plus probable du fait de la présence de la minéralisation dans les zones cisaillées a carbonates secondaires et pyrite cataclastique."

Jan 1, 1990

By A. C. Ter-Oganesyants, N. N. Anisimova, G. P. Kotukhova, G. N. Dylko

The process utilized at Norilsk Nickel Polar Circle Division for treating slimes from the electrorefining of copper and nickel was developed in the late nineteen fifties and has survived without any fundamental changes. This technology is a combination of pyro and hydrometallurgical operations to produce PGM concentrates that are sent away for refining. The characteristic feature of the current technology is multiple-stage, extended cycle treatment with significant incomplete production, low labour and automation efficiency and poor hygiene and sanitary conditions. To eliminate all negative aspects mentioned above, specialists of Norilsk Nickel Polar Circle Division have developed a new hydrometallurgical process for treating electrolytic slimes. The main steps of the flow sheet developed are autoclave leaching of the slimes and electrochemical opening-up of a cake from autoclave leaching. The implementation of the new process will allow Norilsk Nickel Polar Circle Division to shorten the process cycle 4-5-fold thus reducing the volume of incomplete production, considerably increase labour efficiency, simultaneously improving working conditions, upgrade the final concentrate, reducing costs and increasing PGM recovery during refining and, ensure higher security of precious metals by employing automated processes and vacuum sealed units.

Jan 1, 2004

By S. Sakurai

"Gravitational force is an external body force acting on underground structures. It should be noted that gravitational force cannot be replaced with the surface traction vector (Cauchy stress) which is an internal force. This fact should be properly taken into account in a numerical analysis of underground structures, particularly for structures such as vertical shafts, tunnels, and caverns constructed at great depths. It is obvious that the gravitational force must be conserved at all times.In conventional numerical analyses, the initial state of stress of the ground medium is firstly calculated under the gravitational field. This means that the gravitational force is replaced with stress (surface traction vector), and after that only the initial stress is considered in the calculation of the stresses and displacements of the structure. It should be noted that the initial stress is Cauchy stress consisting of a surface traction vector, while the gravitational force is a body force acting on the mass of the materials. This computational approach may be acceptable for elastic problems because the principle of superposition is valid for elastic materials. However, this approach becomes questionable for elasto-plastic materials because there is no guarantee that the principle of superposition is valid for them.Furthermore, another problem exists in elasto-plastic analyses: The stress state in a plastic zone must satisfy a yielding criterion such as that of Mohr-Coulomb. In order to make the stress state satisfy the criterion, an excess stress beyond the yielding criterion should be transferred to an elastic zone existing outside of the plastic zone. This seems to always be possible, because an elastic zone always exists, no matter how large of a plastic zone appears. In some cases, however, the excess stress cannot be transferred to the elastic zone because the gravitational force must be conserved. Therefore, it is obvious that the magnitude of stress around underground structures may become large and surpass the yielding criterion at great depths where a large gravitational force exists.In this paper, it is demonstrated that in a conventional elasto-plastic numerical analysis of a vertical shaft at a great depth, all the stress components around the shaft become very small, even though a large gravitational force exists. This strange result may be due to the fact that the gravitational force is not properly taken into consideration in the numerical analysis."

Jan 1, 2015

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By L. M. Nolan

Chemical Mechanical polishing, or CMP, has four components in the polishing interface; namely the polishing pad, the polishing fluid, the abrasives in the fluid, and the surface being polished. Understanding the way that load is transferred between these components is key to understanding and predicting wafer polishing. Numerous models of CMP and the different load sharing arrangements which occur between these four components have been proposed. These include models by Luo and Dornfield (1) and Fu, Chandra and colleagues (2). Other models focus on just one or two loading arrangements, such as `hydroplaning' when all load is transmitted by the liquid in the case of Runnels and Eyman (3). In this work, we consider four possible combinations of load transfer from pad to wafer in CMP. These combinations are listed below in Table 1 and are illustrated schematically in Figure 1. It is important to note the role of scale in this process; the illustrations in Figure 1 are drawn to scale from actual profilometer scans obtained over a length of 5 with particles of 150 nm in diameter. Table 1 - Load Transfer Combinations Load Regime Illustration Wafer - Fluid - Pad Figure la Wafer - Particles/Fluid - Pad Figure lb Wafer - Particles - Pad Figure lc Wafer-Pad Figure ld The interest in load-sharing between the system components is because some configurations are anticipated to achieve higher polishing rates than others. For instance, in hydroplaning, or hydrodynamic lubrication, the lateral force exerted on the polished surface by the particles can be no higher than the fluid shear force developed in the gap between the pad and wafer. This is not expected to generate high rates of material removal from the surface (4). For contact that is largely between the pad and the wafer, such as the regime depicted in Figure ld, the lateral load is transmitted to the wafer by the pad and is hence limited by the pad's low rigidity. This regime is not expected to generate high material removal rates either. The highest levels of material removal are expected from regimes where the mechanical load exerted on the system is transmitted by the particles, in combination with either the fluid or the pad. Under what circumstances does the polishing regime change from one to another? What must occur in order to initiate or terminate contact between the system components? This is an ongoing question in the field of tribology, and has traditionally been viewed in terms of the pressure and velocity applied to the system, the thickness of the fluid film between the two surfaces, and the roughness of those surfaces (4). In this paper, we propose a new mechanism ? that the load on the particles may be sufficient to totally embed them in the polishing pad, at which point they are no longer able to transmit load and polish the wafer surface. This is illustrated schematically in Figure 1(d).

Jan 1, 2010

By V. Bruned, K. Mohamed, A. Michaut

Orano Mining Somaïr uranium treatment plant (Niger) uses a pugging-curing process to leach uranium. Sulfuric acid, nitrates and water are added to the finely grinded ore in a rotary drum to leach uranium bearing minerals and solubilize uranyl sulfate ions. Reagents, sulfuric acid and nitrates, are the main OpEx of this process step. The economical optimization of their addition requires a thorough knowledge of the ore behavior in solution with these reagents. Orano Mining technical direction and Somaïr laboratories developed a model to predict the curing process uranium recovery surface with a limited number of parameters. Experimental laboratory work to fit the model needs to be done for each type of ore which can require a lot of metallurgical tests and would be time consuming. In order to optimize the required number of tests, an innovative experience plan was designed in parallel to the development of this model reducing the required number of tests to only eight. Once the parameters of the models are correctly fit, the comparison between the estimated values and the actual values for the uranium recovery is excellent (less than 0.5% error in average). Associated with an updated cost model of the curing process, this new recovery model helps the plant operator find the best set of reagents to maximize curing process profitability in the Somaïr plant day after day.

Jan 1, 2020

By Philippe Portella

Current Ownership : AREVA NC-France & affiliates (63.4%), ONAREM-Niger (36.6%)Related Mines : Ariège, Artois, Arlette(initial Somaïrlease) and Tamou, Taza, Takriza, Tamgak(SMTT lease)Mining Method : Open Pits Reserves : about 14 000 tU Average grade : 0.3 % UEnvironmental Management : Certified ISO 14001 since November 2002Key figures :2003 output : 1126 tU number of employees at year end : 565 Current Ownership : AREVA NC-France & affiliates (34%), ONAREM-Niger (31%), OURD-Japan (25%), ENUSA-Spain (10%) Related Mines : the Akouta mine provides access to several adjacent orebodies(Akola, Akouta, and coming Afasto with Ebba North / South)Mining Method : Underground ?mainly room & pillars Reserves : about 29 000 tU Average grade : 0.40 to 0.50 % U3O8Environmental Management : Certified ISO 14001 since January 2003Key figures :2003 output : 2017 tU number of employees at year end: 1070

May 1, 2006

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By M. Kowalczyk

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of the (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gemstones.

Jan 1, 2009

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By P. D. P. Hamilton

IT is perhaps obvious to most individuals who are interested in the mining industry that a producing mine has been subjected to several phases of engineering attention. In this paper it is the author's hope that a thoughtful survey of these various engineering phases will emphasize certain points of value and interest which may sometimes be overlooked. The points which we will bring out are being made in an analytical sense and are not in any way a reflection on any individuals or organizations which might see in these illustrations a similarity co chair particular conditions. In other words, we are drawing on our general experience to illustrate the points which we chink are worthy of mention, and which we believe are of a type sufficiently frequent co be emphasized. It is well co point out chat, in this paper, we are not concerned with the relative importance of such theoretical questions as to whether or not a geologisc is more important than a prospector, or the office manager than the surface foreman. We are, however, interested in analyzing the various types of engineering experience required in the bringing of a mining enter-prise from the early prospect stage in co-production, and their importance to the project as a whole. In order to simplify our analysis of the subject, it has seemed best to outline a simple mining organization. In using the terms 'industry' and 'business', we feel chat frequently those engaged in mining do not always appreciate that mining is actually an endeavour, or a business, which has the same economic fundamentals as any other business. In the mining industry, the field and producing engineering are counter-parts of the research and production phases of any other type of business. Once this is realized, it is fairly obvious that mining, like any other industry, is a matter of economically acquiring raw materials, processing them, and finally marketing the resultant commodities as favourably as possible. The points may be discussed in a little more detail as follows.

Jan 1, 1938

By V. Feldman, I. Holl, J. Zampini

"The Renard Mine, 100% owned by Stornoway Diamonds, is located approximately 250 km north of the Cree community of Mistissini and 350 km north of Chibougamau in the James Bay region of north-central Québec. The project benefits from a large and growing resource, good mining conditions, strong social acceptance, a modest environmental footprint, and the development of direct-to-mine road infrastructure. Construction began on July 10, 2014; following the completion of a 946 million CAD project financing transaction. Now completed, the mine is the first diamond mine in Québec, and one of only six in Canada, employing approximately 500 people. First ore was delivered to the plant approximately 5 months ahead of schedule on July 15, 2016. Commercial production was declared on January 1, 2017. In general, the project ramp up has been characteristic of a type 1 McNulty curve. One of the challenges during production ramp-up was a redesign of processed kimberlite dewatering (replacing the dewatering centrifuge with two stages of hydrocyclones and a dewatering screen). A processing opportunity captured by Stornoway was the design and installation of an ore sorting facility which rejected free waste rock from the valuable host rock; kimberlite. Through tackling both challenges and opportunities, Stornoway has realised and is now exceeding their original design tonnage.PROJECT DESCRIPTION Stornoway Diamond Corporation (Stornoway) was established in 2003 resulting from to a plan of arrangement between Northern Empire Minerals Ltd. and Stornoway Ventures. In 2011, Stornoway acquired 100% interest of the Renard Mine. The construction of the Renard Mine began in 2014 and achieved full production in 2017 [1, 2]."

Jan 1, 2019

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By F. Fournier Dit Chabert, F. Tancret, J. François Castagné, R. Le Gall

During the repair of turbine blades by a laser cladding process, it is observed that interdendritic cracking occurs in the heat affected zone (HAZ). Auger electron spectroscopy, performed on sample broken at high temperature, reveals interfacial sulfur segregation, which is known to be one of the main causes of microcraking in the HAZ during welding processes. Moreover, thermal gradients generated by the process are responsible for important thermomechanical stresses. In the present work, the finite element code Comsol Multiphysics is used to simulate the laser cladding process in order to determine both the thermal field and, using an elastoplastic law, the stress field inside the component. The originality is that the temperature history calculated in the thermomechanical model is extracted then injected in a segregation model in order to calculate the local segregation behavior. This model can be eventually used to predict the risk of cracking as a function of process parameters and alloy chemistry.

Jan 1, 2006

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018