Search Documents

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By J. P. Sairrlon, K. G. Wheeland, K. J. Mintz, B. J. Kiener

Iwenty-one ore dusts of varying mineralogy, sulphur content and reputed in-mine explosibility were selected from eight mines. After chemical and mineralogical analysis and sieving into two size fractions (+45/ -63 microns and -45 microns), these sarrples and seven pure minerals were tested for explosibility in oxygen in a Harbnann chamber. '!he maximum explosion pressures and maximum rates of pressure do not correlate with sulphur content alone; the types of minerals are also .important. Residues were analyzed to check the combustion reactions. Further comparisons between laboratory and mine results are planned to improve predictability.

May 11, 1988

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the 'contract' system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011

By T. Y. Chong, J. A. Folinsbee

Since milling began in 1909, the PJV Dome mill has been expanded several times, to the current throughput of 11,500 tonnes per day. PJV recovers free gold using crushing and grinding followed by gravity concentration. The remaining gold in the gravity tails is recovered by cyanide leaching followed by Carbon-In -Pulp processing. Prior to 1993, cyanide tailings were impounded in the tailings pond where cyanide was allowed to degrade naturally. Effluent was discharged seasonally during the summer and early autumn to maintain the water balance. In 1993, an Effluent Treatment Plant (ETP) was designed and constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO SO2/Air cyanide destruction process was added to the ETP. Even though the ETP was successful in meeting the cyanide, metals and total suspended solids (TSS) discharge limits, often the treated effluent failed to pass toxicity tests. Following successful laboratory and plant scale testing, the addition of the chelant EDTA (ethylene diamine-tetra-acetic-acid) was commenced in the 1999 operating season. To date, discharged effluent has passed all toxicity tests. This paper describes the evolution of the ETP from its early conception to the various phases of upgrade needed to meet the MISA discharge limits.

Jan 1, 2005

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

By G. Archibald, M. McSaveney, J. Wartman, M. Yetton, C. Massey, C. Holden, A. Kaiser

"The 2010/11 Canterbury earthquakes triggered many mass movements in the Port Hills including rockfalls, rock and debris avalanches, slides and slumps and associated cliff-top cracking. The most abundant mass movements with the highest risk to people and buildings were rockfalls and rock/debris avalanches. Over 100 residential homes were impacted by landslides, leading to the evacuation of several hundred residents.Volumes of rock leaving several of the larger cliffs during the earthquake sequence were determined from terrestrial laser scan change models. There were no seismically instrumented cliff sites and there was some distance between the cliffs and nearest strong-motion sites. Therefore, we synthesised free-field rock-outcrop seismograms by employing a stochastic approach controlled by source models and regional parameters derived using spectral inversion of the extensive strong motion data set. Relationships between volumes leaving cliffs during the earthquakes and site peak ground acceleration (PGA), peak ground velocity (PGV) and Arias intensity were compared for different sites. Multiple linear regression was used to analyse the variables that best predict the volumes of debris that fell from the slopes during the main earthquakes. The best correlation between the volume of debris falling per square metre of slope face and the seismic forcing parameters was for vertical PGV. The results from the multiple linear regression incorporating slope height, inclination, PGV horizontal and PGV vertical, improved the statistical relationship.Field data and results from the 2D seismic site response assessment indicate that the following factors affect dynamic performance of the modelled cliffs: 1) cliff geology—mainly material modulus, shear strength and shear wave velocity; 2) slope geometry—ridge-scale versus site-scale effects; and 3) the temporal aspects of the earthquake shaking (i.e., single acceleration peaks of large amplitude versus multiple peaks of smaller amplitude). Model results show that amplification of shaking does not increase linearly with increasing height, but instead reflects changes in the cliff geology where material strength, modulus and shear-wave velocity contrasts lead to acceleration contrasts.These factors show that the use of well documented case histories provide the basis for more certainty in seismic landslide assessments compared to those that are only empirically based."

Jan 1, 2015

By P. J. Dunlop

THE object of this paper is to present a brief survey of the work done and the results obtained in controlling dust at the Hollinger Consolidated Gold Mines milling plant. The plant includes all primary and secondary crushing, grinding, and treatment operations. The major items of equipment are: (1) Underground Crusher Plant 1 48 in. by 60 in. jaw crusher, crushing run-of-mine ore to minus-6-in. Rate: 420 tons per hour (2) Surface Crusher Plant 3 No. 772 gyratory crushers 3 4 ft. by 16 ft. trommel screens 4 No. S gyratory crushers Reducing ore to rninus-172-in. Rate: 420 tons per hour (3) Roll Plant 5 sets of 62 in. bJ: 24 in. rolls 7 5 ft. by 10 ft. v1bratrng screens Delivering a minus-3/16-in. finished product Rate: 420 tons per hour (4) Grinding Plant 4 7 ft. by 15 ft. low discharge grate ball-mills 4 12 ft. reciprocating rake classifiers Rate: 4,800 tons per 24 hours Maximum capacity: S,800 tons per 24 hours

Jan 1, 1939

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

By T. A. Chepushtanova, I. U. Motovilov, V. A. Luganov, G. D. Guseynova

"Kazakhstan has significant reserves of oxidized nickel ore with low nickel content. Processing of such ores is effective via pyrometallurgical technologies such as smelting to ferronickel or matte with consecutive extraction of metals from melting products. There are also many options for direct hydrometallurgical processing. However, they do not provide high nickel recovery.We studied extraction of nickel and cobalt by using combined technology of low-grade ore processing from the Shevchenko Kazakhstan deposit, which includes smelting to poor matte followed by hydrometallurgical processing of the matte. The nickel content in the initial ore was 0.75–0.9%. Pyrite concentrate of Sokolov-Sarybai Kazakhstan deposit containing 0.17% cobalt and 0.06% nickel had been used as a sulphidizer at smelting.As a result of the study, we were able to extract up to 98% of the nickel and up to 80% of the available cobalt. Obtained matte contained 3.1% nickel, 0.29% cobalt, 71.6% iron and 24.3% sulfur. Matte leaching was carried out by hydrochloric acid. The iron content in the pregnant solution was 170–185 g/dm3. Nickel and cobalt precipitation from the pregnant solution was carried out by hydrogen sulfide. Initial matte or cast iron was used as neutralizers during the process. Practically complete precipitation of nickel was achieved at 3–5% excess of neutralizer at 333–343°K in 4 hours; up to 95% of cobalt precipitation was achieved in 50% excess of neutralizer at 363°K in 8 hours. The purified solution contained 200–600 mg/dm3 of nickel, 80-100 mg/dm3of cobalt and 175–185 g/dm3 of iron. The purified solution allows to obtain iron oxides by high-temperature hydrolysis, and to regenerate hydrochloric acid.As a result of non-ferrous metals precipitation we obtained sulfide concentrate with concentration of Ni up to 25% and concentration of Co up to 5.5%. The technology is recommended for semi-industrial testing."

Jan 1, 2016

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

In this study, we develop a detailed model of the likely future carbon footprint of primary copper supply. We develop a peak copper production model, based on a detailed copper resource data set, and combine this with a comprehensive life cycle assessment model of copper mining and milling to predict greenhouse gas emission rates and intensities of Australian and global copper production up to 2100. By establishing a quantitative prediction of both copper production and corresponding greenhouse gas emissions of Australian and global copper industry, we then analysed the emissions intensity of various energy input scenarios, such as business-as-usual, solar thermal electricity and solar thermal electricity with biodiesel. The Australian Government has an aspirational goal for long-term greenhouse gas emissions of an 80% reduction from the 2000 level by 2050. For the copper sector, this means moving from about 12.6 Mt CO2e in 2000 to a goal of some 2.52 Mt CO2e in 2050 (assuming equal emissions reductions across the economy). Based on the energy sources modelled, only the solar thermal plus biodiesel scenario was capable of achieving this goal at about 0.15 Mt CO2e, since the solar thermal alone scenario still includes normal petro-diesel as a major source of emissions. Overall, it is clear that there are abundant resources which can meet expected long-term copper demands, the critical issue is more the carbon (and environmental) footprint of different copper supplies and use rather than how much is available for mining. It is clear that the switch to renewable energy can have a profound impact on the carbon intensity of copper supply, even allowing for increased energy intensity as ore grades decline, and a complete conversion to renewable energy will position the copper sector to meet existing annual greenhouse gas emissions targets and goals.

Aug 1, 2013

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By G. M. Brownell

Introduction The Flin Flon mine is located on the boundary line between the provinces of Manitoba and Saskatchewan at a point about four hundred miles northwest of Winnipeg. A branch of the Canadian National railway provides the town of Flin Flon with direct transportation facilities. The property was staked in 1914 and, after a considerable amount of exploration; the Hudson Bay Mining & Smelting Company was organized and brought the property into production in November, 1930 (1). Mining is carried on by open pit and underground methods at the rate of about 4,400 tons per day. Production for the year 1934 was: 99,334 ounces of gold; 1,335,319 ounces of silver; 37,486,054~pounds of copper; and 49,427,280 pounds of zinc; in addition to small amounts of cadmium and selenium. The Flin Flon deposit is one of the largest low-grade ore deposits in Canada with complete hydro-electric and metallurgical plants for the production of blister copper and electrolytic zinc. Previous Work The development of the Flin Flon mine into one of the major mining operations in Canada has created a need for a more detailed geological study of the area. Practically all of the information published to date concerns the general surface features. It is the purpose of this paper to deal more specifically with the ore-body and its relationship to the enclosing rock as revealed by studies made possible through recent underground development. The earliest published report on the area is by E. L. Bruce (2), who made a reconnaissance geological investigation of the region for the Geo-logical Survey of Canada in 1914 and established the main. petrological units. Several years later the area immediately around Flm Flon was mapped in greater detail by F. J. Alcock (3). In the summer of 1934, the area of Missi sediments to the north and east of the mine was studied by J. W. Ambrose. His report has not yet appeared in print but his findings are of importance.

Jan 1, 1935

By Marcel M. Djivre

The paper will outline the destructive test methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. For the evaluation of the mechanical properties of rope samples used in "ultra-deep" single-lift shafts, additional discard criteria used in Ontario, Quebec and South Africa shall be presented. Most of the methods and test procedures currently used at MTL can also be found in the current CSA G4-00 Standard, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage, published in November 2000. In this latest or sixth edition of CSA Standard G4-00, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The CSA G4-00 Standard is also intended for the manufacturing of new ropes, and includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish. To-date the Ontario Mining Regulations require only that destructive test of new ropes be performed in accordance with CSA Standard G4-00, but does not require conformity to the Standard, and on the other hand the inservice wire ropes are required to be tested in accordance with CSA G4 and thus require conformity. The author recommends that the Ontario Mining Regulations (and regulations of other mining jurisdictions) be improved in order to ensure quality control in the manufacturing of wire ropes destined for mines in Ontario (and Canada). Also, the author recommends the revision of the CSA G4-00 Standard by the technical committee in order to address manufacturer?s concerns with respect to compliance, and harmonize the Standard with Internationally recognized Standards.

Apr 1, 2005

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016