Search Documents

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By F. H. Edmunds

LLOYDMINSTER is the centre of a well developed agricultural area, lying on the Alberta-Saskatchewan interprovincial boundary in Township Fifty. The surrounding country is gently undulating, without any notable topographic features, but twenty-two miles to the north the North Saskatchewan river, and thirty miles to the south the Battle river, have cut deep valleys. In the spring of 1934, a wild-cat well (Lloydminster Gas Company's No. 1 well) was successful in striking a large flow of gas at a depth o 1,974 ? feet. The gas was piped into the town, a short distance south, and Lloyd-minster became the first Saskatchewan town to be served with natural gas. Following this discovery, other wells were sunk and, up to the present, thirteen wells have been drilled m what is here designated the Lloydminster area. Ten of these wells are in Saskatchewan and three in Alberta. Seven were successful in obtaining gas, three oil, and three have been unsuccessful. The area tested by this drilling is about eight thousand acres, six thousand of which can be considered as proved gas or oil land. To the south and west of Lloydminster, in the Province of Alberta, there are several areas in which oil and gas have been discovered. The Wainwright field lies nearly fifty miles to the southwest; Battleview, where recently gas has been discovered, is thirty miles west-southwest; and the Ribstone area is about thirty miles south and a little west. At Ribstone, a number of wells were drilled some years ago and there is a small production of oil. The data relating to the wells in the Lloydminster area that are recorded in this paper are taken from the records of the several companies operating in the field. The names of these companies are given on the map and on the type stratigraphic section (Figures 1 and 2). The author wishes to record his appreciation to Mr. R. H. Shaw and Mr. 0. C. Yates, both of Lloyd-minster, for much valuable information; also to Mr. E. Swain, of the Department of Natural Resources, Regina, with whom the writer has visited the field on several occasions, and who, by his enthusiasm and encouragement, has done much to forward the development of the area. The well samples were examined at Ottawa by officers of the Borings Division of the Geological Survey of Canada, who also made the interpretations of the logs. Frequent references will be made to the work of Dr. G. S. Hume, of the Geological Survey, and the writer would like to pay tribute here to his work.

Jan 1, 1940

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By W. A. Lang

"IntroductionCARBONIZATION, gasification, and chemical utilization of coal are interrelated topics, which makes it difficult to review one without indicating its connection with the others. Hence, in Progress in Coal Technology, Series No. 5: Carbonization, reference was made to gaseous products recovered in the carbonization of coal, and .to a number of chemicals made from the tars, light oils, and ammoniacal liquors which are by-products of coal carbonization.In this, the sixth paper in the review series, prime consideration will be given to the complete gasification of coal to give a fuel for domestic industrial, or power purposes and a synthesis gas suitable for the manufacture of gasoline, Diesel oil, and chemicals. The hydrogenation of coal, an alternative source of liquid fuels and of chemicals, will be reviewed, as will be a number of processes for •the recovery of chemical products from coal by extraction and chemical treatment."

Jan 1, 1952

By N. Dave

"IntroductionIn the mineral processing industry, certain minerals such as uranium, thorium and vanadium, etc., are selectively extracted with high degree of purity from solutions containing variety of other impurities by solvent extraction process. This separation process consists of bringing two immiscible or partially soluble liquid phases in contact, where mass transfer of one or more components takes place by ion exchange under certain controlling parameters such as pH, salt concentration and temperature. The processes taking place are primarily physical because the solutes being transferred are ordinarily recovered without chemical change. For efficient extraction more than one stage is required and the solutions are recycled counter currently through other stages. A multi-stage counter current solvent extraction plants essentially consist of four circuits namely: extraction, water wash, stripping, and solvent scrubbing. In extraction circuit the desired mineral is extracted at a certain pH from an aqueous solution onto an organic solvent by bringing them in contact with mixing in large mixer-settler units. The mixed solutions are allowed to settle and separate into component organic and aqueous phases in horizontal settlers by providing sufficient residence time. The solutions are then moved counter currently to other units- the aqueous from the underflow and the solvent organics from the overflow of the settler. The solution streams coming out of extraction circuit are loaded organics and barren aqueous or raffinate solution. The loaded organics are washed with water in a water wash circuit to remove transported impurities from extraction circuit. In the stripping circuit, the desired mineral is stripped selectively from the solvent phase back into an aqueous phase with a stripping agent at a selected pH. The solution stream leaving, stripping circuit are stripped organics and pregnant strip (aqueous) solution. The stripped organics are scrubbed off other loaded impurities with a conditioning solution in, scrubbing circuit and the cleaned solvent is re-used in the extraction circuit.A typical solvent extraction plant for uranium extraction and purification at Agnew Lake Mine is described in this chapter."

Jan 1, 1989

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

By J. Jankovic

Numerous advantages have been recognized for solid oxide fuel cells (SOFCs) operating at temperatures of 500-700°C. However, there are several issues related to low temperature SOFCs, such as high electrolyte resistance and high electrode polarization. One of the routes to enhance the electrode performance, particularly for the cathode, is to use new materials with optimized microstructure. In this work, the plasma-spraying technique, recognized to have several advantages over presently used deposition techniques, was used to deposit cathode materials onto ceramic and stainless steel substrates to obtain highly porous structures. Cathode materials with composition of Lao 6Sr0.4Co02Fe0 8O3 (LSCF) were employed in the powder form. The LSCF was prepared from powder precursors with different pore formers and binder levels, or from already produced, single-phase LSCF. The (La0.8Sr0.2)0.98MnO3 (LSM) cathode material was also processed for comparison purposes. The deposition process was developed to obtain coatings with good bond strength, porosity, film thickness and residual stresses. The phase and microstructure of deposited materials were characterized using XRD and SEM.

Jan 1, 2005

By Staff

Introduction The Hedley mine, perhaps better known as- the Nickel Plate mine, is one of the outstanding properties of southern British Columbia. Discovered in 1898 by Woollison and Arundell, prospectors, the property was bonded in 1899 to M. K. Rodgers for the Marcus Daly Estate, of Butte, and development was started the same year. From the high grade of the ore outcrop, and its colour, due to oxidation of the arsenopyrite, it was not difficult to open up and trace the showing. The Nickel Plate ore-shoot, which apparently had been easy to follow on surface, was more difficult to trace underground. In 1903, prospecting on an adjoining property, the Sunnyside, showed commercial ore at surface, but it was only after two years' work that the ore-body was defined and shipments started. From this property, $1,200,000 have been taken out. Prospecting was also carried on on the IXL, Climax, Copper Cliff, Mound, Bulldog, Exchange, Silver Plate, Gold Plate, and other properties, all of which had surface showings, but up to date only the Nickel Plate, Iron Duke, Morning, and Sunnyside have produced commercial ore. In 1904, the Bulldog looked like a very promising mine, but it failed to make good. In 1905, the Sunnyside No. 1 was in the limelight, but it also failed to make the grade. In 1906, an outcrop on the Sunnyside No. 3 looked interesting. Subsequent work. on this claim produced $840,000, and at the same time ore which yielded $400,000 was mined from the Sunnyside No. 4. In 1908, the Nickel Plate ore-body entered a lean zone and, as the diamond drill failed to give satisfactory results, the Daly Estate, after making a profit of $1,151,000, sold the property to the Hedley Gold Mining Company, Limited, for $760,000, retaining, however, a large interest.

Jan 1, 1929

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By Edward Martinez

Due to its unique properties, chrysotile asbestos is used in many diversified applications. In recent years, a better understanding of the structure and properties of chrysotile has evolved due to the research efforts of many investigators. A summary of the results of some of these investigations is given. An attempt is made to show the relationships between the properties of chrysotile and its crystal structure. Examples taken from the literature are cited in which methods have been developed for modifying the properties to improve the performance of asbestos in some applications. These include the effect of pH on the positive zeta potential and the addition of sodium silicate to improve filtration characteristics. The dehydroxylation and formation of forsterite when chrysotile is heated are also discussed.

Jan 1, 1966

This paper outlines the position and capabilities of Western Canada's bituminous coal industry, and indicates the increasing importance of Japan as an export market. The use of coal in Japan is reviewed, especially as regards future trends, and an appraisal is made of Canadian coal in comparison with domestic Japanese coal and imports from other countries. The importance of maintaining a solid nucleous within the Canadian bituminous coal industry is emphasized. I N RECENT years, Japan has emerged as a valuable market for Canadian exports. The first major product exported in volume to Japan was wheat, which has become very successfully established in Japanese markets. Following this, iron ore gradually found a market in Japan, with exports usually based on long-term contracts. This iron ore was produced entirely in British Columbia In 1958, the Western Canadian bituminous coal industry -jointly with the Dominion Coal Board -sent an official mission to Japan to investigate the

Jan 1, 1964

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

Building off the enthusiasm generated by Credit Suisse First Boston on the potential benefits of an industry-wide effort to market gold jewellery, a group of gold producers, led by Randall Oliphant, CEO of Barrick Gold, decides to investigate the long -term impact of launching a significant marketing initiative to stimulate demand for gold jewellery. The group establishes an international Steering Committee representing producers of differing sizes, members and non-members of the World Gold Council. This Committee comprises representatives from AngloGold, Barrick, Gympie Gold, Kinross, Randgold, and Sons of Gwalia and is supported by the Australian Gold Council, the Gold and Silver Institute, and CSFB. The Steering Committee hires McKinsey to assist it by conducting an independent review of whether investment in a large-scale marketing initiative for gold jewellery would be effective in increasing demand for gold, and ultimately of significant economic benefit of the gold industry. Based on McKinsey?s review* and its own discussions with key stakeholders across the industry, the Steering Committee strongly believes the case for marketing is compelling and sufficiently proven to persuade the industry to undertake a major initiative over the next few years. The Steering Committee, supported by McKinsey, conducts briefings with a range of gold producers to share its findings and to understand producers? perspectives on an industry-funded marketing campaign. The Steering Committee is asking for your support to bring this industry-funded marketing campaign to life.

May 1, 2002