Search Documents

By Constantin Pitis, Paul Slatter, Behnam Pirouz, Laura Contasti, Markus Zeller, Sadegh Javadi

"The centrifugal slurry pumps feeding cyclones are critical components used in the grinding process. It is well known that for this type of pumps the performance degradation is very intense. To minimize downtime a complete stand-by slurry pump is always installed in a parallel circuit. The replacement decision of slurry pumps is sometimes set on specific periods of time that are empirically determined, based on previous experience; unless a pump failure triggers the second (standby) pump. Given the significant energy costs in the grinding process and a desire to increase competitiveness, engineers and scientists started research in this field while manufacturers also took actions in order to improve pumps reliability and performance. The lack of standardization regarding the methods used to benchmark and evaluate the energy performances of cyclone slurry pump systems in the mining industry makes it difficult for an enterprise to take informed decisions concerning the replacement or optimization of its process based on energy benchmarking of such slurry pump systems. This paper proposes a new methodology of benchmarking slurry pump performances using a new concept of Benchmark Energy factor (BEF) based on Mathematical Model Benchmarking. The concept of BEF has been proven successful in other industries. A new standard addressing the guidelines for benchmarking the energy performance of slurry pumps for cyclones was proposed within the Canadian Standards Association. This standard will provide a unified and consistent methodology for performing measurement activities with the ability to measure and verify the system energy performance in the field through the BEF approach. Practical examples based on the new concept are presented with comments."

Jan 1, 2017

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By P. C. M. Knops, K. Rijnsburger, R. M. Santos

To overcome the challenges of mineral CO2 sequestration, this work utilizes a unique proprietary Gravity Pressure Vessel (GPV) reactor technology, and focuses on reaction products of high economic value. The GPV provides intense process conditions through hydrostatic pressurization and heat exchange integration that harvests exothermic reaction energy. Here, laboratory-scale tests of the envisioned process was performed in tubular and continuously stirred tank reactor (CSTR) autoclave reactors. The mineral used was Olivine (~Mg1.6Fe2+0.4(SiO4) + ppm Ni/Cr), although asbestos, steel slags and oil shale residues are also under investigation. The effect of several process parameters on reaction extent and product properties was tested: CO2 pressure, temperature, residence time, additives (buffers, lixiviants, chelators, oxidizers), solids loading, and mixing rate. The products (carbonates, amorphous silica and Chromite) were physically separated (based on size, density and magnetic properties), characterized (for chemistry, mineralogy and morphology) and tested in intended applications (e.g. as pozzolanic carbon-negative building material). Economically, it is found that product value is the main driver for mineral carbonation, rather than, or in addition to, the sequestered CO2. The approach of using a GPV and focusing on valuable reaction products could thus make CO2 mineralization a feasible and sustainable hydrometallurgical process.

Jan 1, 2015

By Bong Sun You

AZ31 magnesium plate of 300mm in width and 40mm in thickness was produced by horizontal continuous casting machine, and its microstructures were analyzed on the surface and in the plate interior. The defect formation on the surface and subsurface, such as side cracks, buckling, pores and segregation, was very sensitive to the casting condition and processing parameters. Especially, casting speed and secondary cooling were the most dominant parameters to control the solidification behavior of magnesium melt, for example the position and shape of the solid/liquid interface in the mould. The cyclic marks on the surface were obvious because the plate were drawn by 4-step cycle and can not be removed. The average grain size of as cast plate measured as 50-65µm at the near surface and 300-400µm in the center of the plate was relatively small because secondary cooling water was applied to control the surface quality resulting in rapid solidification of the melt in the mould.

Jan 1, 2006

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GRG) test procedure at McGill University is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill University has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GRG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. Around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill University. As a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GRG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GRG tests were carried out at McGill University on ores from all over the world. Recently, a modi?ed version of the GRG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GRG in a sample; this simpli?ed test has the advantage of reduced mass, processing time and cost. To recognize and honour the contributions made by the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GRG test be named after Laplante.

Jan 1, 2010

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By Rick Steen, Weldon Read, Morrism Tracy T.

Edging for starter sheet blanks used in conventional copper refineries has always been problematic for getting the edging to seal and adhere to the titanium material used for the blank so that copper is prevented from plating under the edging and cause undo problems in getting the copper sheets to separate from the blanks. A method was developed at the Amarillo Copper Refinery utilizing an injection molding process that better adheres the edging material to the titanium that makes the harvesting of starter sheets much easier to the point that robots are now used to strip with and which holds up very well to the unforgiving physical nature of the electroplating process. It is believed that this technology could be successfully utilized for permanent cathodes as well. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery. The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By A. M. L. Cushing, S. Kelebek

Presently, adsorption is one of the effective methods of removing toxic contaminants from waste waters. The contaminants from metal mining industrial operations include an effluent water containing various types of heavy metal species at concentrations beyond the maximum allowable limits, which are 0.5 ppm and 0.3 ppm for nickel and copper species, respectively. Adsorption behavior of copper ions pre-chelated with diethylenetriamine (DETA) and triethylenetetramine (TETA) onto natural bentonite and peat has been investigated. Both natural bentonite and peat was found to be capable of removing these copper-polyamine complexes from aqueous solutions relevant to process water effluents. However, the adsorption capacity of bentonite was significantly higher than that of peat. Two models were used to study the adsorption kinetics: a pseudo-first-order rate expression and a pseudo-second-order rate expression. For both adsorbents, the data conformed best to the pseudo-second-order rate expression. Representation of the experimental data through adsorption models was also investigated. Out of the four cases considered, namely, Langmuir, Freundlich, Temkin and Dubinin-Radushkevich isotherms, it was found that for both bentonite and peat, the copper polyamine adsorption data conformed best to the Dubinin-Radushkevich adsorption model. The Langmuir model also represents the bentonite-copper polyamine adsorption system reasonably well as the second best case, suggesting that the amount adsorbed on bentonite might be a monolayer with strong affinity.

Jan 1, 2015

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

Abstract-This paper discusses the fundamental question, "what is an adequate sample size?" in the light of recent developments regarding parameters of Gy’s well-known formula for predicting sampling variance. New understanding of the granulometric factor, g, and the liberation factor, l, had significant impact on the results of calculations involving Gy’s equation. For the granulometric factor, justifications are given as to why nominal comminution size should always be reported as P95 (i.e., the screen size rejecting 95% of the mass). A small but important change in the model to estimate the liberation factor makes the difference between a predictive formula that works or does not. Other parameters and considerations regarding their practical implementation are commented upon in light of the author’s experience.

Jan 1, 1998

By R. G. L. McCready, Marco Zentilli

"Brogan coal containing mean averages of 6,93% w/w total sulphur (1.1% sulphate sulphur, 1.6% organic sulphur and 4.24% pyritic sulphur) and 16.34% mineral ash was used as the test coal in these studies.Shake-culture leaching studies on seven size fractions of the coal, ranging in size from 0.045 mm to 1.7 mm, showed that the rate of pyrite leaching was inversely proportional to the particle size. As the use of continuous stirred tank reactors would be uneconomical for the reclamation of waste coal, column leaching studies were initiated on coal sieved to >6.35 mm to < 12.7 mm, The leachate was monitored for all metal ions and the release of iron was used to monitor the rate of pyrite oxidation . Measurable amounts of Zn, Co, Ni, Mn, and V, all of which can replace iron in the pyrite crystal structure, were released during the initial stages of leaching. Further, high concentrations of AI, Ca and Sr and trace amounts of Sn, As. Se, B, Ca, Cr, Si, and Ti were detected in the column effluents.These studies suggest that bacterial leaching will remove the pyrite and qualitative amounts of environmentally undesirable trace metals from the coal if such a process is developed for waste coal reclamation.IntroductionIn 1947, Colmer and Hinkle showed that acid mine drainage was the result of an oxidative attack of the iron-mineral sulphides by Thiobacillus ferrooxidans to produce sulphuric acid . Ashmead (1955) proposed the use of these organisms to desulphurize coal , but the subsequent research effort was concentrated on the metabolism and physiology of these extreme acidophiles.A limited number of studies have been reported on the bacterial leaching of pyrite from coal (Silverman et al., 1963; Dugan, 1977). However, the bacterial oxidation of pyrite is a self-limiting first-order reaction, probably due to the precipitation of Fe(OH)J and elemental sulphur , which progressively inhibits intimate contact between the bacterial cells and the sulphide-mineral surface. Consequently, the best pyrite oxidation experiments with coal reported to date required five days to remove 97070 of the pyrite (Dugan &Apel , 1978) using mixed cultures of T. ferrooxidans and T. thiooxidans."

Jan 1, 1985

By Guocheng Pan

Geostatistics has been widely accepted as a standard tool for reserve estimation and mine planning. Kriging has been adopted as the best estimator of grade. Although many discussions have been conducted in the use of kriging in the mining industry, insufficient attention has been given to solutions for over-smoothing. This effect has been frequently encountered in many mines. The so-called over-smearing refers to two facts: (1) over-reduction of grade variabilities and (2) over-estimation of low-grade ore tonnages. This study attempts to link over-smoothing effects with several other practical aspects in kriging. These include the weight independence of data values, variogram modeling, and search strategy used in estimation. All solutions recommended here are suited for precious metal deposits (e.g. gold) in open-pit mining.

Jan 1, 1995

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

By N. C. Carter, Wm. H. White, J. E. Harakal

"Of twenty-one ore deposits in British Columbia which are either in production or advanced stages of exploration, five have potassium-argon ages in a range of 165-205 m.y., eight are in a range of 44-55 m.y. and the remainder are either ca. 140 m.y. or ca. 100 m.y. old. Deposits of the oldest group have generally similar geological environments and radiometrically indistinguishable ages of magmatic and hydrothermal minerals. Deposits of the youngest group also have similar geological environments, with successive magmatic and hydrothermal events closely intermingled in time and place. Such deposits find no comfortable home in existing classifications of ore deposits. 1t is suggested, therefore, that those epigenetic deposits which can be shown by radiometrie and/or geologie means to be coeval with genetically related magmatism be designated as ""paramagmatic deposits."""

Jan 1, 1968

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004