Search Documents

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965

By A. C. Hnatyshyn

INTRODUCTION THOSE concerned with coal mining operations in Alberta have been asked repeatedly the same question, "Why is mechanization in Alberta proceeding so slowly as to lag far behind the mines in the United States?" This question is often asked in such a manner as to indicate that a severe reprimand is overdue to the mining engineers of this Province for their apparent indifference to the problem of improving their mining operations by increased mechanization. To the average person, unacquainted with mining conditions and problems, mechanization appears to be simply a matter of introducing equipment to load coal underground and, once this is done, substantial economies in operating costs will automatically follow. Invariably, those who have followed this simple reasoning have found, to their regret, that such is not the case and that effective mechanization involves something more than the mere process of introducing loading equipment into a mine. To be effective, any programme of mechanization must take into consideration all operations incidental to the mining, transportation, and handling of the coal from the working face to the tipple, and must utilize equipment which can be best adapted to any peculiar condition or circumstance prevailing in the mine concerned. In the use of such equipment, the net and final result should be an improvement in operating costs of sufficient magnitude to at least return to the operator, over a specific period of years or during the expected life of that equipment, all his investment plus a fair return on that investment.

Jan 1, 1951

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By MacKenzie Dickson

"INTRODUCTIONGold is found in many natural states, native nuggets, loose grain in river sands, veins in rock, as well as associated with sulphides, oxides, etc., disseminated more or less minutely.Its high value in recent years has spawned new technologies to win values from sources once considered too lean for commercial recovery. Cyanide leaching from fine milled ore or tailings, from upstream recovery operations, coupled with adsorption onto relatively coarse granules of activated carbon, concentrate the gold enough to be converted to bullion by time-honoured methods.The carbon granules are fragile. Size degradation in handling must be minimized not only to prevent loss of gold on fine fragments of carbon that could pass with the barren tailings, but to maintain adsorption efficiency. Besides, the granulated carbon itself is costly. Circular Vibroscreens are winning acceptance for dewatering carbon granules thanks to their gentle yet effective performance in gold recovery systems around the world. The system at Equity Silver is illustrative.BackgroundEquity Silver Mines Ltd., Houston, British Columbia, first began production in September 1980. In 1984, a feasibility study showed that additional gold and silver could be economically recovered through cyanide leaching of the flotation tailing.Although the carbon-in-pulp (ClP) or carbon-in-leach (CIL) process is commonly used for extracting precious metals from slurries, the use of circular vibrating screens, and Vibroscreens in particular, for the carbon circuit is an innovation that cuts costs.Rectangular vibrating screens have been the conventional separation mechanism of choice across North America. In contrast, the use of Vibroscreens has been proven to be less costly for the initial purchase and installation. Also, these circular vibrating screens require less power and less space. A description of Equity Silver Mines' process shows how these screens have been successfully integrated into the system."

Jan 1, 1989

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By Y. Rama Murthy, Amit Ranjan, Pankaj Satija, Sunil K. Tripathy

"Chromite ore is one of the essential raw materials for ferroalloy and steel industry. Boula-Nuasahi belt of Sukinda region, Odisha, is the only resource of chrome ore in India. The Indian deposits are typically characterized as ferruginous and siliceous type ores. Chrome ore is generally mined by open cast mechanized mining method in these areas. The run-off-mine (ROM) ore from the various mines is sent to beneficiation plant via stack yard for further up gradation. The chrome ore beneficiation plant (COB) has two major circuits: comminution (feed preparation) circuit and beneficiation circuit. In the comminution circuit, the ore is reduced to <1 mm size ( for complete liberation of chromite) from -220 mm size in stage wise crushing (primary and secondary crusher) followed by screening and single stage grinding in a ball mill. Fraction having size <1 mm is further upgraded in the beneficiation circuit to produce three different concentrates having specific chemical composition and Cr: Fe ratio. The beneficiation plant is a complex circuit comprising of combination of unit operations (spiral concentrator, Floatex density separator, hydrocyclone, wet shaking tables). In the recent years the overall performance efficiency (grade and recovery) of the beneficiation circuit got affected with numerous changes in the run-off-mine ore quality (physical and chemical), mineralogical composition, etc.In this article, attempts made for improving the performance of chrome ore beneficiation circuit is discussed. The approach adopted and practical problems encountered while the process were also highlighted. The results of the trials has shown an improvement in the performance of the cyclone (d50 : 56 µm – 40 µm) and chromite losses into tailing to <12%.INTRODUCTIONChromite has a wide range of application, from refractories to metallurgical industries, and from chemical to non-ferrous alloy industries. Chromium ore (Fe2+, Mg) [Cr, Al, Fe3+]2O4) occurs exclusively in rocks formed by the intrusion and solidification of molten lava or magma which is very rich in the heavy, iron containing minerals such as pyroxene and olivine. With the richness of silica and iron, the chrome ores are broadly classified as siliceous type and ferruginous type. Pure chromite with composition FeCr2O4 is rare because magnesium usually substitutes for ferrous ion and aluminum and ferrous ion substitutes for chromium. Generally the associated gangue minerals are talc, quartz, hematite, goethite, limonite, gabro, serpentine, anorthosite, dunite, pyroxinite, etc. Around 96% of the chromite ore production is consumed for metallurgical applications of which 94% is converted into different grades of ferrochrome i.e., high carbon ferrochrome and charge chrome as shown in Figure 1. Stainless steel being the leading consumer of ferrochrome, any change in the dynamics of the stainless steel industry impacts overall chrome ore demands significantly."

Jan 1, 2016

By E. C. Harder

BRITISH Guiana, Great Britain&apos;s only South American colony, may be reached by very comfortable steamers, both from North America and Europe. The trip from North American Atlantic ports requires about 12 to 14 days; that from Europe about 18 to 20 days. A number of steamship lines, including Canadian, American, and Dutch, have regular sailings between North America and British Guiana, with calls en route at various interesting ports in the West Indies and northern South America. Moreover, several lines, including British, German, and French, have steamships operating regularly between Europe and the West Indies. Indeed, so popular have the West Indian voyages become in recent years that, during the winter months, special cruises in considerable number are organized for many vessels that ply in the trans-Atlantic service in the summer. A trip to British Guiana, therefore, has become a delightful experience. After visits at the various attractive Leeward and Windward islands and Trinidad, the approach to the low, flat, British Guiana coast, with its muddy coastal waters extending for many miles offshore, is somewhat of a contrast. Arrival in Guiana waters is signalled by the appearance of the modern high-power Demerara Light, located "on a shoal about twelve miles from the mouth of Demerara river. From this point, if the tide is right, a pilot takes the steamer across the bar, eight to ten miles offshore, and into Georgetown harbour. At high tide, the water above the bar ranges from 15 to 18 feet in depth, depending on whether it is neap tide or spring tide; at low tide, the corresponding depths are 9 to 11 feet. As the bar is of soft mud, however, it is usually possible for vessels to pass over it with a draught of about two feet in excess of that indicated by the tide tables. Upon nearing the shore, one sees first the Georgetown wireless towers, then the light-house and the tall chimneys of sugar mills and of various factories in Georgetown, and finally the palms and other tropical trees and the houses of Georgetown itself along the sea shore and the east bank of Demerara river. Extensive wharves operated by various exporting and importing companies stretch along the river bank and activity prevails in Georgetown harbour. The principal exports are sugar, rice, gold, diamonds, bauxite, balata, lumber, fruit and other tropical products. The imports are food-stuffs, wearing apparel, and manufactured materials of many kinds.

Jan 1, 1936

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author&apos;s views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

By Ali Roshanfekr

Linear mine-waste dumps at open-pit mine sites essentially represent expedient places to deposit large quantities of waste rock. Being in valleys in most cases, the effect of the water flowing through and out of the deposit often raises questions about their hydraulic behaviour and geotechnical stability, especially the zone of the downstream toe. In order to provide better tools to assess the behaviour of these dumps a laboratory and analytical study was conducted. Firstly, physical models were built to assess the flow capacity and hydraulics associated with the linear growth of such dumps. It was found that the elevation of the point of first-emergence on the downstream side becomes constant after the dump grows to a certain length, but that the upstream depth concurrently increases. The limits of applicability of the theories of Hansen et al. (1995, 2005) are discussed in this regard. Secondly, in analysing the seepageface downstream, two approaches for solving this spatially varied flow (SVF) problem were undertaken. Under one of the approaches links to SVF depths were merely made to the hydraulic heads of the body (interior) and flux was calculated using conventional surficial nodes after the fact, Under the other approach flux nodes were used to link the SVF algorithm to the hydraulic heads further ?inside? the body of the rockfill. Although there are inherent uncertainties, it was found that these two methods can be made to perform equally well. Research continues but it appears that a linear variation in depth can be assumed without inducing any unrealistic exit gradients in the zone of primary concern with respect to unravelling.

May 1, 2011

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

The writer presents a concise summary of eleven recent discoveries made in the Maritime Appalachian area, with suggestions for fur the research. This information may prove helpful to geologists working in other fields and to students contemplating further avenues of research in mining geology and exploration. INTRODUCTION THIS paper is not intended as a research study on the subject, but i. merely a brief review of eleven discoveries that have been made in the Canadian Appalachian area. Furthermore, this is not a critical analysis of the merits of any one geophysical method, but it is an un-prejudiced observation of how these discoveries were actually made and what techniques were apparently most fruitful. Some generalizations are attempted whicl1 may suggest further avenues of research in the field of mining exploration. The writer wishes to thank his colleagues in the field for their comments, which he was able to in-corporate into this paper. In particular, he is grateful to Dr. Paul Bevan and

Jan 1, 1963

By J. F. Henderson

THE National Advisory Committee on Research in the Geological Sciences was established seven years ago - in 1949. In 1952, shortly after the Committee had really begun to function and had issued its first report, a paper ( l) was presented describing the objectives and organization of the Committee and the progress to that time. Another four years have gone by and the Committee feels a further progress report may be of interest. HISTORY Ten years ago, in 1946, the Geology Division of the Institute set up a Committee on Geological Research. This Committee, under the Chairmanship of Dr. J. E. Hawley, recommended that "a National Advisory Committ.ee on Research in the Geological Sciences be formed" (2). With the backing of the President and Council of the C.I.M. this recommendation went forward to the then Minister .of Mines and Resources and, with his approval, to the Committee on Scientific and Industrial Research of the Privy ?Council. As a result, the National Advisory Committee was set up in 1949.

Jan 1, 1956

By G. D. Garland

"IntroductionALTHOUGH the presence of rock salt in the Carboniferous basin of northern Nova Scotia has been known for at least one hundred and twenty years, and salt has been mined at Malagash continuously since 1919, certain characteristics of the deposits make exploration by drilling or surface examination difficult. The surface rocks of the basin are, in general, of Pennsylvanian age, while the salt occurs in the Mississippian Windsor group. The latter rocks are brought to the surface only along anticlinal folds, or as irregular fault blocks. Because of the limited areal extent of these Windsor exposures, and their complicated internal structure, geophysical surveys, especially gravimetric, can be of considerable aid in outlining the more favourable areas.The present paper describes the results of recent investigations by the Dominion Observatory, in cooperation with the Nova Scotia Department of Mines. It includes a regional study of that section of the Cumberland basin lying between Springhill and Malagash ( Figure 1), and a much more detailed survey of the immediate vicinity of the Malagash deposit itself. This deposit had been studied by Miller (6, 7) with the torsion balance nearly twenty years before, and a direct comparison between the results given by the two types of instruments is therefore possible."

Jan 1, 1955

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

By D. H. d Hamly

THE work of Brown and others at Pittsburgh (Brown, Baum, Yant, and Schrenk, 1938)(1) and the success of their light field microprojector (Figure 1), have shown that the microscopy of dust quantitation can be greatly improved. It has been shown that dark-field microprojection of dust spots on konimeter slides is possible (Pullen, 1940), and this paper is a discussion of the new microprojector and a new counting method which is made practical by this instrument. The microscope makes possible the ready determination of the dustiness of mine ventilation air. Reduction of the dust concentration from a dangerous to a safe level involves one or more of the following: reduction of dust production, filtration of the air stream, or dilution with non-dusty air. Each of these raises important engineering problems of time and costs, and trustworthy information on the state of dustiness of the air is required ?both before and after the employment of any method of reduction. Records of this information may be divided into two broad classes concerned with safety: (1) the level of dustiness, and (2) the quantity and kind of dust produced by a machine under a given set of conditions. Though the first requires only one determination for a given time and place, numerous routine records are required to show the continuous safety of the air in an actively producing mine. Though repeated samples are required, highly accurate counts are not needed to show safety or to indicate whether a substantial increase in the non-dusty ventilation air has produced a proportionate decrease in the dustiness of the mixed air. The Devers and Gathercole konimeters have proved satisfactory instruments for this purpose in Ontario.

Jan 1, 1942

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By J. L. Wilson

"Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. To assist the new operators, the SAG Mill at B2Gold’s Fekola Mine in Mali needed a robust control that could handle load changes and unmeasured disturbances with minimal operator intervention. With modern Distributed Control Systems (DCS) powerful enough to run advanced control, they often have Model Predictive Control (MPC) blocks built in or available as an “add-on” license, and thus MPC can be readily implemented within the modern concentrator with a relatively low added capital cost. This paper discusses an implementation of two single output MPC controllers to control the SAG Mill at Fekola. This was implemented using the existing signals and advanced control blocks available to the installed DCS.INTRODUCTION Many modern concentrators with VSD driven SAG mills still rely on the control room operator to manually adjust the speed in reaction to increasing bearing pressure. All too often, the problem with this strategy is that by the time the operator reacts with a sudden speed increase, the SAG Mill is likely already on its way to loading up. The next step the operator may take may be to cut back the feed rate, or production until the SAG is once again stable. With this sudden reaction comes an abrupt change in SAG rotational speed and power consumption that sends a surge of material down the circuit as the mill suddenly ejects more pulp. Furthermore, choosing a higher rotational speed can lead to higher than normal liner wear as the cataract overshoots the toe of the charge and impacts the liners. After start-up at B2Gold’s Fekola Gold Mine in 2017, the SAG mill was being controlled manually. The SAG rotational speed was adjusted manually by the operator in step changes depending on whether the SAG bearing pressure was increasing, decreasing or stable. During this time of manual control, the SAG fresh feed rate was also adjusted to a tonnage setpoint with a PID controller. Generally, the SAG fresh feed rate setpoint was kept at a target value, but then the feed rate was throttled back if the SAG mill or grinding circuit showed signs of overloading. The extra challenges were that the operators had limited experience and were concurrently learning how the plant operated. Also, they were also occupied with managing situations in the rest of the plant. Often their attention was drawn away from the SAG mill and during that time, the SAG Mill would load up before they could react."

Jan 1, 2019

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014

By W. J. Bennett

"I AM very happy to have this opportunity of speaking to the Montreal Branch of the Canadian Institute of Mining and Metallurgy.I have selected as the subject of my remarks transportation in that area which is at present our only source of uranium -Northwest Canada. Considering the widespread interest in atomic energy, the end-product of uranium, it may be wondered why I have not chosen to speak of a more spectacular aspect of the development. I hope it will be evident from what I have to say that transportation plays a very dominant role in our effort to maintain a continuing supply from Eldorado's producing property at Port Radium on Great Bear lake and from its coming producer at Beaver lodge Lake in Northwest Saskatchewan. Moreover, transportation has such a bearing on the entire mineral development of the Northwest that it cannot help but be of concern to an organization of this kind. Finally, the transportation problem, of which I shall try to tell you something, is quite unique and the story of its solution or partial solution is, I believe, an interesting one.Transportation experience on this continent indicates that the cheapest method of moving freight is still by water -with •rail, highway, and air transportation following, and in that order •of economic significance. Excluding rail transportation, since the area has as yet no railway lines, this order also applies in the Northwest. I shall direct my remarks to the two kinds of transportation which serve our uranium producers -water and air."

Jan 1, 1952