Search Documents

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988

By K. J. Mintz

Conveyor belts installed in an underground mine can be a potential source of a major fire, thus the need for fife-retardant belting. A Canadian Standard, CAN/CSA-M422-M87, incorporating a small-scale flame test, a drum-friction test, a flame propagation test and an electrical surface-resistance test, has been developed to meet the varied needs of the mining industry. It is recommended that mines use Types A and B belting described in that Standard, because they will have passed the large-scale flame propagation test, rather than Type C, which does not require that test. Belting that has been approved by the U.S.A. Mine Safety and Health Administration (MSHA) may be much less fire-retardant than any Canadian approved belting.

Jan 1, 1992

By S. Jordanov

The nature of processes that take place on top of copper bearing grains during the suppression of copper acid drainage from mine tailings was studied on a grain model. Cyclic voltammetry (C.V.) was employed as an experimental technique suitable for indirect measuring of copper leaching. Experiments were done in sulfuric acid (pH=2) at electrodes that progressively approach the real situation during acid main drainage, starting with Cu-metal, then with CuO and finally with CuO covered with CaSO4. Oxidation was found to be the only process that takes place on metallic copper electrode anodically polarized up to 2 V vs. Cu/CuSO4 reference electrode. Dissolution is intensive and reaches up to 50 mA.cm-2. When the same was repeated, but on CuO electrode, anodic currents were some 4 times lower than on the bare metallic surface. This indicates that the electrode material is not completely oxidized to copper(II)oxide and the Cu(O) or Cu(I) residues are oxidized during the anodic polarization. This explains the diminished dissolution. Dissolution is further restricted at electrodes covered with CaSO4. It is some 20 times lower than on the bare oxide electrode. When the second layer of CaSO4 was applied, anodic currents were another 15 times lower. Total decrease of anodic currents when transition is made from Cu-metal to CuO covered with 2 layers of CaSO4 reaches up to 7.500 times. C.V. measurements produced a proof that mechanical blockage is the way how lime prevents leaching of copper bearing grains in immobilization experiments referred elsewhere.

Jan 1, 2007

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By Brian Penney

"The Iron Ore Company of Canada (IOCC} has mined and processed an iron deposit in Western Labrador along the Labrador-Quebec border since the early 1960' s. Current capacity is approximately 19 million tonnes of concentrate, 70% of which is converted to pellets at these facilities.The ore deposits are located in hills rising 150 to 300 meters above the adjacent lakes, and most of them are covered by very little overburden. The iron minerals are mainly specular hematite and magnetite hosted in a quartz formation. Crude ore averages 40% Fe that is concentrated to 65.5% Fe. IOCC is an extensive operation extending from Labrador City NF to Sept-Iles Quebec. It consists of open pit mining, concentrating, pelletizing, railway, and dock loading facilities.The Concentrator liberates iron from the silica by crushing and grinding the ore to -14 mesh (-1190 microns}. Ground ore is concentrated in spirals and filtered for transportation. Spiral tailings are treated in a Magnetic Recovery Plant (Mag Plant} that recovers lost magnetite. Mag Plant tailings are treated in a Hematite Spiral Plant (Hem Plant} that scavenges fine iron remaining in this stream.This report deals with ongoing iron recovery initiatives within the ConcentratorIron Losses in the ConcentratorIron recovery at IOCC is approximately 70.5%. This compares with recoveries that range from 65% to 86% for other iron mines in our area. Other world large iron ore producers dig and ship concentrate quality ore directly out of the ground and have an effective recovery of 100%. With increasing costs for labour, equipment, and supplies an increase in iron recovery is required to keep the operation viable.More than 90% of our iron concentrate is produced by gravity separation using spirals. The physical characteristics of the iron minerals that most effect recovery are mineral grain size and degree of liberation. We divide ground ore into three size categories -coarse, intermediate, and fines. A brief description of each size fraction follows:"

Jan 1, 1996

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By Randy Billing, J. Fraser Wilson

"IntroductionThe job of designing and implementing effective environmental management sounds like what one executive, assuming responsibility for a very sick organization with lots of potential described as, ""an insurmountable opportunity"".Effective environmental management is an opportunity, no doubt. Its an unusual, if not unique opportunity. Insurmountable? Maybe not! Indeed, in the authors' experience, the keys to unlocking this opportunity are not in new or complicated technicalities; they are in the existing strengths and successful experience that one has in managing other complex and exacting management issues.To begin, it is necessary to understand what these issues of sustainable development mean to business. What is the nature of this opportunity? What makes it look unsurmountable?New Games: New RulesLawyers have described some of the new rules companies are facing and there is a new game being played; a game characterized by unique challenges.Take two, for example: • The ecological problems to be faced are Mother Nature's business, the political solutions required are our business. This combination of natural problems and political solutions requires the development of new management mechanisms, to bridge the gaps among us, as individuals, as professions, as interest groups and so on; indeed, even as countries;• and gaps there are : about as many gaps as the people involved : many of them with new and changing expectations, often mutually exclusive and not negotiable.The challenge of these relationships and communications among so many different interests is one of the keys to effective environmental management.Like any game, this one has rules and they are new, too. These rules are evident not just in new legislation - tough legislation with draconian penalties; they are also evident in new and exacting business policies, value driven and just as unforgiving of poor performance. Senior management of many companies are speaking about the role of enlightened corporate policies and how important it is for everyone involved that these policies drive and reflect business practices. Absence of day to- day behaviour which evidences the words in action, the policy on the wall of a corporate office or published in an Annual Report is first evidence for the prosecution , not the defence.The challenge of practical policies is another key to effective environmental management.This is a new game, with new rules: the challenge of change."

Jan 1, 1991

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By Brian O'Hearn, Doug Hanson

"The most commonly used tendon supports in the Sudbury area include rock bolts, rebars, friction anchors and cable bolts. Due to the fact that these tendons are physically different and employ different anchoring systems they offer varying degrees of stiffness, yield ability, load capacity, anchor dependability and energy absorption. These differences coupled with variable rock mass and changing stress conditions have made it challenging to engineer the design of an effective support system. By tapping into the knowledge and experience gained by ground control practitioners, an empirically based rating system has been assembled that offers a guide to designers of support systems when choosing the most effective tendon support over a range of rock mass and stress conditions.A methodology referred to as support planning can be used to design support systems whose rehabilitation costs will be minimized. The use of multiple tendon types in anyone support layout is advocated, particularly when the stress state of the rock mass to be supported is expected to undergo a change."

Jan 1, 1995

By Jie Zhu

Coal bumps are a special form of release of geologic strain energy that has already been one of the most dangerous hazards to underground mining safety in China. A number of coal-bump models have been developed to quantify coal failure under assumption that a bump is a kind of non-gas induced outburst. However, some technical experts in charge of micro-seismic and gas monitoring have found unusual gas emissions before and after bump, which suggests that it is possible for gas to trigger coal bumps. Considering the coal reservoir as geological body composed of the coal matrix and gas, a new model based on Lippmann?s bump model is proposed to understand the initiation of coal bumps. The redistribution zone from excavation of a roadway has been calculated and analyzed regarding its relation with mining depth. It is shown that high gas pressure may push the coal seam to overstep the critical state due to extension of the plastic disturbed zone, and this is harmful to the stability of coal seam. This model successfully explains the bump phenomena of the Xinzhouyao mine at shallow depth.

Aug 1, 2013

By G. Vibert Douglas

"Gold occurs in Nova Scotia in three ways, saddle reefs, fissure veins, and fossil placers. Of these the saddle reefs are the commonest. They have been the source of most of the gold and have also been the subject of most of the literature on the gold occurrences.The Meguma or Gold-bearing series of Nova Scotia is a conformable succession of quartzite's and slates, possibly Precambrian in age, which have been folded into a number of anticlines and synclines that strike (Fig. 1) roughly east and west. This folding has been termed Acadian and is probably a westward continuation of the Caledonian revolution in Britain. It may have started in the Ordovician and continued through the Silurian and into the Lower Devonian. It was followed by the intrusion of the great Devonian granite batholiths. It is thought that the mineralization is connected with the late phases of the cooling of the granite. As the name saddle reef implies, the veins form on the crests and flanks of the anticlines, possibly in the synclinal troughs as well. The beds favoured by the solutions are the slates. The reason for this is apparent when it is realized that in order to fold over 30,000 feet of sediments (the thickness of the Meguma according to E. R. Faribault) through p radians of arc it is necessary to have a differential movement between the top and bottom beds of p times the thickness of the sediments. In the case of the Gold-bearing series, in which strong quartzite beds lie between incompetent slate beds, most of this differential movement was taken up in the slates. The evidence for this is the remarkably fine drag folding and the intense shearing and comminution of some of the beds of slate (Fig. 1). The quartzites exhibit some shearing and faulting, but there is little doubt that the greater permeability lay along the incompetent slate beds. The mineralizing solutions followed these beds and also passed from one slate bed to another through a joint or fault in the intervening bed of quartzite. These joining veins are called angulars in Nova Scotia. Within the veins the gold is in shoots and the real problem is to find out what controls the position and extent of the shoots."

Jan 1, 1954

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By W. G. Schultz

"Sylvite's potash mine, which produces 8,000 tons of ore per day, probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hour production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tons per hour. The ore is produced by two Marietta miners weighing 258 tons, the largest and heaviest pieces of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000-ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground. Because Sylvite's mine is a new operation with equipment of a new design, the full potential of the operation has not yet been realized. The ultimate capability is clearly evident from the success Sylvite has had over the past year as the average mining capability has risen from 100 tons per hour to 600 tons per hour."

Jan 1, 1973

By George J. Thompson

This pa per deals with the internal characteristics of steel and its response under cold northern temperatures. General maintenance procedures and specific repair techniques are covered.

Jan 1, 1973

By J. W. Matousek

"More copper concentrates are treated in flash smelting furnaces than by any other process, and such furnaces are located in most of the world's major copper producing areas. Except for perhaps two furnaces treating chalcocite-type materials, little difference is seen between the grades of the concentrates being smelted. Within individual smelters, even less variation in feed grades is found. This is both accidental and intended. Many furnaces treat concentrates from captive ores, and these tend to be of relatively constant composition over long periods. Toll smelting operations blend concentrates to ensure delivery of feeds of fixed compositions to their furnaces to avoid upset conditions. Matte grades vary between flash smelting furnaces, but most commonly, these are the result of differences in operating practices rather than because of differences in concentrate grades. This paper reviews an industrial flash smelting test in which the copper content of the furnace feed was intentionally altered over a wide range. IntroductionExcept in a few copper mining regions of the world, the principal copper mineral is chalcopyrite (CuFeSz). This results in the almost universal production of concentrates containing 25070 to 30% copper (and similar amounts of iron and sulphur). Many operators of copper flash furnaces spend their entire metallurgical careers smelting concentrates of essentially fixed grades. This is true both of smelters treating concentrates from captive mines and those processing concentrates on a toll basis. From the production staff's point-of-view, the less variation in grades seen by the furnace, the better. Fixed analyses of concentrates and constant feed rates produce consistent quantities of matte at a consistent grade for processing by the converters. The result is, even in smelters treating a variety of concentrates, efforts are expended in sampling and blending to ensure feeds of relatively uniform compositions being sent to the furnaces."

Jan 1, 1993

By Robert Walker

Agenda ? Investment thesis ? Engagement ? Competitive advantages Corporate engagement ?The ESG Services team carries out engagement activity with the companies in the Ethical Funds portfolio on behalf of investors ?Each year about 50 companies (20% of our assets) are placed on our Focus List based on assessment of significance and severity of ESG risks and the extent of our portfolio exposure ?We engage in direct discussions on material ESG issues ranging from climate change to human rights to executive compensation ?This enables the team to gain insight into how management is addressing various risks to the business and encourage positive change where gaps exist

Aug 1, 2013

By S. Razavialavi

In the planning phase of every construction project, layout of temporary facilities is a crucial task; site layout can affect safety, travel cost and time, construction productivity, and space utilization. However, site layout planning can be a complicated problem, due to the interdependency of influencing factors. Although interaction among activities is one of the major drivers of site layout planning, it has not been properly addressed in past research. In this study, simulation is presented as a promising tool to address this gap. The capability of simulation technology to model complex processes in construction projects makes use of simulation tools in site layout optimization problems effective, while existing methods are unable to perfectly model these problems, in some cases. Additionally, the advantages and challenges of implementing simulation are assessed and a generic framework for simulation application in site layout planning is proposed.

Aug 1, 2013

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By F. Sheykh-Jaberi, S. L. Cockcroft, A. B. Phillion

A coupled fluid/structure model has been developed to simulate semi-solid deformation in an industrial aluminum casting alloy, A356. Although this alloy has a significant eutectic fraction, nearly 50%, it still shows susceptibility to hot tearing. The model geometry consists of solid grains, created from a Voronoi tessellation of the domain, surrounded by liquid. The simulation is performed using the commercial codes, Abaqus Standard and Abaqus CFD. The solid model calculates the velocity, stresses and distortions in response to an applied uniaxial strain, and transmits them to the fluid-flow model, which computes the velocity and pressure fields in the liquid. It was shown that grain size and configuration, fraction solid and fluid properties all affect the semi-solid deformation behaviour.

Jan 1, 2014