Search Documents

By Charlie Graham

Our Approach ? Industry Trends ? New Forces at Work in Mining ? Deep Mining ? Energy projects ? Air power ? Hydraulics ? Electric alternatives ? Drilling ? Productivity ? Conclusions ? Transportation ? References

Oct 1, 2010

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By H. Alzraiee

Traditional planning methods such as CPM and PERT have been useful tools to manage construction projects. However, the underlying model of these traditional methods often seems to fail to represent real projects as they tend to assume no interrelationship between project components. In reality, project components have complex dynamic feedback process that requires modeling of inherent uncertainty in the execution of these projects. Nevertheless, this dynamic nature and uncertainty have not been explicitly addressed by traditional planning methods. Project failure can be attributed to poor representation of the inner and outer aspects of operations that are responsible for project dynamics. Uncontrollable external forces are often cited but the real cause may be internal such as the feedback process among components of the project. An alternative perspective is offered in this paper through system dynamics (SD) that accounts for the feedback process and discrete event simulation (DES) for modeling the uncertainty. The proposed method utilizes SD method for modeling project dynamics and DES method coupled with CPM network for operational details and uncertainty, respectively. A case study that involves preparing engineering drawings in a design office is used to demonstrate the use of the developed method and to highlight its capabilities. Modeling the dynamic dimension is expected to enhance planning and scheduling of construction operations and to provide a better understanding of the impact of various internal and external factors on project schedule and productivity performance.

Aug 1, 2013

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By C. Arson

We modeled mode I fracture in shale with an equivalent damage zone (CDM), a cohesive zone (CZM) and discontinuous enrichment functions (XFEM). In the Differential Stress Induced Damage model (DSID model) used in the continuum approach the total work input is equal to the sum of the energy released by crack debonding, the energy dissipated by crack opening, and the elastic strain energy stored in the bulk outside of the damage zone. In CZM and XFEM, the overall stiffness of the rock mass in the process zone drops as soon as the fracture starts propagating (unstable fracture propagation), whereas rock elastic properties in the CDM equivalent damage zone evolve smoothly with the displacement imposed at the boundary of the domain. In the CZM and XFEM, fracture propagation stabilizes after a turning point: this point coincides with damage initiation in the DSID model. As a result, the total energy of the rock mass calculated with CDM is about twice as large as in CZM and XFEM. The relative energy components of the rock mass are in the same order of magnitude and follow the same trends in the three models. This numerical study compares the evolution of dissipated energy potentials during mode I fracture propagation, and is expected to provide a basis to predict the amount of energy released by discrete fracture growth vs. damage propagation in the fracture process zone.

Jan 1, 2015

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By Tobias Riedel, Peter Ay, University of Applied Sciences, Bianka Bade, Nicole Pausch, Bernhard Gemende, Florian Logsch, Matthias Leiker, Satyanarayana Narra, Claudia Glaser

This study focusses on the production of micro-structured agglomerates with high porosity from iron (III)-hydroxide-containing materials as adsorbent. A fractal-like structure of the agglomerates was created through a two-stage agglomeration process. Developing porous structures was necessary to increase the adsorption capacity. Various materials were used for the agglomeration experiments: i) filter cake (dry matter content 23 to 27 wt.-%); ii) FerroSorp®DGµ, a product which is already being used commercially for various applications in water cleaning. These materials in the pristine state have different characteristics such as dry matter content and particle size distribution. The desired optimised agglomerates can be achieved with the help of additives or binders, respectively. Additionally, the agglomeration process parameters play a vital role. In order to produce agglomerates with high porosity, the process was carried out in two steps. Firstly, FerroSorp®DGµ (d90 < 30 µm) was agglomerated jointly with the aforementioned filter cake in an Eirich intensive mixer (particle size range 125 µm < d90 < 500 µm). The second agglomeration step post drying was carried out in a pelletisation disc or in an Eirich intensive mixer with the addition of polymeric binders (up to particle sizes ranging from 2 to 4 mm). Agglomerates were characterised both in short and long term loading tests using phosphate as model ion. Contact times were less than 10 min, similar to practical application in percolation columns, or more than 7 days, respectively. The results show that the agglomerates produced in the two-stage pelletisation process have more advantageous properties like better accessibility of the active sites obtained by specificly influencing the particle size distribution during the two-stage pelletisation process.

Jan 1, 2016

By S. I. Saif

The Key Anacon deposit lies about 6 miles northeast of the Brunswick NO.6 mine of Brunswick Mining and Smelting Corporation. Geological mapping, especially in the well-exposed Nepisiguit River section, geophysical data, and information from extensive underground and some surface drilling show that the rocks at Key Anacon are similar in many aspects of stratigraphy and structure to those of the Brunswick Mine area. They include narrow beds of fine acid volcanic material interpreted to be metatuff and volcanogenic metasediments. The massive sulphide ore body at Key Anacon lies immediately above these acidic rocks, in association with other chloritic, sideritic or magnetic iron-rich metasediments. The iron formation, which is similar to that associated with other orebodies in the district, is overlain by massive andesitic material. Four phases of structural deformation have been recognized in the Key Anacon area; they are similar in intensity and style to those of the Brunswick No. 6 mine area. The orebody lies in a zone of complex isoclinal folding along the flank of a major F2 fold (Key Anacon Syncline) and in general appears to be stratiform. The ore occurs in probable F2 parasitic folds, and this suggests a complicated structural geometry superimposed on the original beds. The general similarity of the mineralization at Key Anacon, together with its occurrence with other iron-rich metasediments between a footwall of acid volcanic material and overlying andesitic rocks, is suggestive of stratigraphic time-equivalence with the Brunswick zone . If so, the metavolcanics at Key Anacon might have been derived either from a center within the main volcanic pile to the west or from a smaller local center active at the same time. Alternatively, the Key Anacon ore could have been formed during a much older volcanic cycle. The solution to this aspect of the problem is the subject of a continuing study.

Jan 1, 1978

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

Presentation Plan Hoist ropes ?Importance ?Mandatory and routine Inspections Continuous monitoring of wire ropes for mine hoisting ?Why a continuous monitoring of mine hoisting ropes.? ?Description of the ??Contiscan?? monitoring system ?Information data gathering Advantages of the ??Contiscan?? monitoring system ?Visual rope inspection on daily basis ?Monthly inspection ?Payload capacity flexibility and potential increase for deep mining operations. ?Periodical inspections by external experts ?Importance of the costs associated with hoisting production shutdowns. Commercialization and availability

Aug 1, 2013

By Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"A Jet Diffuser Flotation Column (JDFC) is a newcomer flotation device whose operation principles similar with Jameson cell but it has an essential change in downcomer. By taking into account the hydrodynamic and fluid mechanic principles (Sahbaz et al. 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogenous dissipation of the bubbles in the separation tank. Thus the performance increase has been aimed for the coarse particles.According to theoretical results, obtained by the formula of Oteyaka (1993) showing the relationship between velocity gradient and maximum floatable size for the various contact angles, the d50 of quartz flotation of JFDC is about 240 µm and 310 µm for the contact angle of 50° and 60°, respectively. This result was verified by the experiments. According to the experimental results; d50 which was accepted the maximum floatable particle size of quartz flotation of JFDC was about 256 µm and 300 µm for the contact angle of 50° and 60°, respectively.INTRODUCTIONFlotation is a kinetic process used for separation of hydrophobic particles from hydrophilic particles. There are many different parameters affects the success of the flotation and particle size is one of them. While the flotation is very efficient for intermediate size, the efficiency of the process starts to decrease for both fine and coarse sizes (Trahar, 1981; Muganda et al., 2011). Therefore; researchers have tried to find a solution for the efficiency decrease in fine and coarse sizes by modifying the chemical condition and designing the new devices. For example, Jameson cell is a unique device for the fine particle flotation due to the suitable design and fine bubble producing (Jameson, 1988; Evans et al., 1995; Sahbaz, 2010). Because of this success operation the Jameson cell is applied more than 200 flotation plants in worldwide. On the contrary, the efficiency of the cell decreases for coarse particle flotation due to the turbulence occurred in the separation tank (Sahbaz, 2010; Cowburn et al., 2007). That’s why, new flotation device was designed in loboratory scale by Sahbaz, Oteyaka and Ucar in 2010s and it has been called as Jet Diffuser Flotation Column (JDFC) recently."

Jan 1, 2016

By Sigmund J. Andersen, Eva A. Mørtsell, Jostein Røyset, Randi Holmestad, Oddvin Reiso, Yanjun Li, Øyvind Paulsen, Calin D. Marioara

"With the purpose of increasing the extrudability of lean alloys, we reduce levels of the alloying elements Mg and Si in a 6xxx extrusion alloy. To avoid sacrificing strength, we investigate the compensating effect of smaller amounts of lithium and germanium, alone and in combination. Recent studies by atomically resolved high angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with density functional theory (DFT) calculations have demonstrated that while Li replaces Mg, Ge substitutes Si in the columns in the hardening ß’’-phase. Several studies have shown that Ge replaces Si in other precipitates as well, and that both Li and Ge promote precipitation and can improve macroscopic properties, like strength and thermal stability. The scope of the current work has been to investigate and document the combined effect of the two alloying elements. Of the investigated alloys, the one containing both elements displayed highest hardness, corresponding with a significant increase in precipitate number density. We used HAADF-STEM to determine the extent of Li and Ge in the precipitate structures.INTRODUCTION The two most important alloying agents, with respect to age hardening of the 6xxx alloy series, are Mg and Si. In general, 6xxx alloys are formed into their final shapes by rolling or extrusion, before being age-hardened at elevated temperatures around 180°C. The hardening effect during this stage is due to the formation of metastable, semi-coherent, precipitate needles along the three < 001>Al directions generally following the precipitation sequence (Marioara, Nordmark, Andersen, & Holmestad, 2006): Supersaturated solid solution ? atomic clusters ? Guinier-Preston-zones (pre-ß”) (Edwards, Stiller, Dunlop, & Couper, 1998) (Marioara, Andersen, Jansen, & Zandbergen, 2001) ? ß” (Andersen, et al., 1998) (Hasting, et al., 2009) ? ß’ (Vissers, Huis, Jansen, & H. W. Zandbergen, 2007), U1 (Andersen, Marioara, Vissers, Frøseth, & Zandbergen, 2007), U2 (Andersen, Marioara, Frøseth, Vissers, & Zandbergen, 2005), B’ (Vissers, Marioara, Andersen, & Holmestad, 2008) ? ß, Si (stable)"

Jan 1, 2018

By A. Dahi Taleghani, A. Shojaei

Continuum damage mechanics (CDM) of rocks is studied together with their elastic and plastic behaviors to develop simulation tools for hydraulic fracturing jobs in naturally fractured formations. The model is constituted based upon pressure sensitive inelastic deformation of porous rocks and their damage mechanisms in the cases of drained and undrained conditions. The CDM model is formulated within Fracture mechanics framework. The performance of the developed elastoplastic and CDM models are compared with the available test data of a specific shale play. The hydraulic fractures growth in the reservoir scale is then simulated; in which the effect of fluid viscosity, natural fractures characteristics and differential stresses on induced fracture network is studied. The simulation results are compared with the available solutions in the literature. The developed CDM model outperforms the traditional fracture mechanics approaches by removing stress singularities at the fracture tips and simulation of progressive fractures without any essential need for remeshing.

Jan 1, 2015

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By D. F. Sangster, P. J. Hood, G. A. Gross

"Some results are presented of an integrated geological and geophysical study of Precambrian magnetite-quartz iron-formation in the Kapiko Iron Range north of Nakina, Ontario. Detailed geological and topographical mapping was carried out in conjunction with detailed geophysical investigations such as vertical magnetic field, vertical magnetic gradient, hammer seismic, horizontal-loop electromagnetic and magnetic susceptibility surveys. In addition, oriented drill cores were obtained for magnetic polarization studies.Vertical-force magnetic anomalies within individual rock units showed a strong positive correlation with topographic relief. Moreover, magnetic intensity was found not to be quantitatively proportional to the magnetite content in the rocks, due to the presence of high remanent magnetization of the magnetite. Also, the remanent polarization direction was sub parallel to the plunge of the fold structure and mineral lineation in associated rocks.Vertical magnetic gradient measurements were found to be more accurate in locating buried contacts between magnetite-quartz iron-formation and country rock than the vertical magnetic force data.An in-situ magnetic susceptibility meter was used to measure the magnetite content of iron-formation, and the measurements were subsequently compared with vertical-force magnetic results.The results of the EM survey were inconclusive; some magnetite-rich zones produced anomalies in the out-of-phase component. whereas others did not. The reasons for such inconsistencies are not yet apparent.Longitudinal seismic wave velocities measured parallel to the bedding in magnetite-quartz iron-formation ranged from 10,600 ft/sec. to 14,500 ft/sec. The seismic velocity appears to increase with an increase in deformation of the rocks."

Jan 1, 1966

By J. D. Botsford

Westmin Resources Limited's H-W orebody on Vancouver Island is a copper/lead/zinc massive sulphide deposit that has been in production since 1985. The sulphur content of the ore averages 28% and in some stopes is as high as 53%. Several minor secondary sulphide dust explosions have occurred in development headings and cut and fill stopes, but as yet no known explosions have occurred in blasthole stopes. This pa:per reviews the history of sulphide dust explosions in the H-W Mine, factors contributing to the explosions and the preventative measures taken to control them.

May 11, 1988