Search Documents

By C. S. Crocker

The Centennial orebody was discovered and named in 1970, Manitoba's centennial year. It is relatively small, about 2 million tons. Strike length varies from 400 to 600 feet and widths from 10 to 60 feet; dip is 75 degrees. Low grade and metal prices demanded low-cost mining, and the mine was developed for conventional sublevel stoping. As the ore lay entirely under a large lake, ground movement had to be avoided and the stopes were to be filled hydraulically. Late in 1973, vertical crater retreat mining was introduced at Inco Limited, Sudbury, to recover pillars between filled stopes. It proved satisfactory and the results were publicized by CIL, who developed the technique. The method seemed to offer some advantages and one stope at Centennial Mine was selected to be mined by VCR while production was maintained from blasthole stopes. The trial stope was safe and showed lower development costs, reduced drilling time, a favourable powder factor and good fragmentation. VCR mining is now an accepted method at HBM&S Co., Ltd., and its use is being extended.

Jan 1, 1979

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By G. Russo

During the construction of the S.Martin La Porte access adit, 9m in diameter, extreme squeezing conditions occurred while crossing Carboniferous schistose formations, with diametric convergence up to 2m. Back-analysis of monitoring results shows that an acceptable simulation of the observed excavation behaviour can be derived using a combined analytical and numerical approach, with simple elasto-plastic laws but a progressive reduction of residual parameters and a relevant increase of dilatancy.

May 1, 2009

By Alan E. Gallie

FOR many years the Witwatersrand has been the leading gold mining r camp in the world and, to a Canadian mining student, could not fail to be of overwhelming interest. The vast scale upon which the operations are conducted, the enormous production accomplished, and the perfection of the operative technique, have all so forcibly impressed themselves on his memory that it is difficult to select any one feature as more outstanding than another. For the purposes of this paper, however, the author has selected the very first feature of mine operation with which he came in contact, namely, shaft sinking, as it reflects, quite as well as any other, the spirit of mining in South Africa. Early mining in Johannesburg was by open cuts or trenches, dug along the outcrops of the reefs. The ore was thrown from bench to bench to the surface. As the depth increased, rock was hoisted by bullocks. In 1887, the first shafts were sunk and true underground work began. At the same time, boreholes were put down to test the continuity of the reefs at depth. The first was at the Village Main reef. It cut the South reef at 517 feet and the Main reef leader at 581 feet. The Main reef leader assayed eleven penny-weights. Subsequent boreholes proved the reefs down to thousands of feet. Many companies secured deep-level claims as a direct result of the information obtained from the early holes. These companies then held land on which there was no readily available ore. In order to get to their pay rock, vertical shafts through the upper strata were necessary. Shareholders were impatient, and shafts had to be sunk as speedily as possible. The old methods of shaft sinking were investigated, new methods developed, and soon all records were being broken. In the last thirty-five years, the record has been slowly advanced, and last summer it was again broken to stand at 430 feet in a 31-day month. During the period from 1915 to 1935 inclusive, in the Witwatersrand district, 96 miles of shafts were sunk. Today, with the advance in the price of gold and the increase in the mining area, there are over twenty-five major shaft-sinking operations being carried on.

Jan 1, 1937

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

Spatial information Critical to a project since it underpins: ?Discovery of mineral resources ?Orebodydefinition and technical assessment ?Mine design and planning ?Profitability and project value Data ?Single most import asset. ?Good interpretation of quality data underpins project growth and success. TEAMWORK

May 1, 2002

By Michael Samis

NOFLEX valuation results ? CF deviations and net CF risk discount factors ??Cash flow deviations indicate average cash flow variability. ??Net cash flow riskdiscount factors (NCFRDFs) indicate the size of the risk adjustment applied to a cash flow. NCFRDFs profile should change with variations in cash flow uncertainty since the risk adjustments applied to the project cash flow reflect investor sensitivity to uncertainty.?DCF and RO will often produce different NCFRDFs for the same project since they use different methods of risk-adjustment.

May 1, 2006

By Y. Qi

A cell-level nonlinear dynamic model of solid oxide fuel cell (SOFC) based on physical diffusion principles is built in this note. It demonstrates that reactant diffusion processes from gas flow bulks to triple phase boundaries (tpbs) play an important role in the dynamic behaviors of SOFC. The simulation shows that under certain condition, the effect of the double layer capacitance may be neglected. The phenomenon of slow rise of voltage in current interrupt experiment may be explained by the dynamic behaviors of partial pressures in the vicinity immediately above tpbs.

Jan 1, 2005

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By Lawrence B. Cochrane, Olivier Tavchandjian, J. Michael Anderson, Christopher R. Davis

"Abstract - Resource modelling is a complex process involving different specialists with relevant experience using a multi-disciplinary approach and the best available technology and reviews by independent auditors. The reliability of the final resource estimate is highly dependent on the quality control exercised at each stage of the process. At each step in the resource modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. Designation of responsibility and authority for meeting these objectives must also be clearly identified. External audits must also be incorporated to review and validate the implementation of new procedures.Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting, classification, and risk analysis."

Jan 1, 2001

By Rainer Süss

An investigation was carried out by Mintek to investigate the influence of a range of alloying additions (vanadium, cobalt, zirconium, antimony and germanium) on the formability and hardenability of alloys with gold content >90 wt%. This paper reports on the hardening mechanisms that can be utilised to increase the hardness of gold (>90 wt% Au) by conventional alloying, as well as the hardening effect obtained by alloying with specific elements. Preparation methods for the alloys are described, which include the steps of melting, annealing, quenching, cold working and age hardening. Focus is given specifically on alloys that were developed at Mintek with a gold content >90 wt%, which are not only harder, but exhibit good resistance to tarnishing and corrosion.

Oct 1, 2003

By Malcolm Scoble

School Values ?? Each other; ?? Students, & helping them develop intellectually, personally & professionally; ?? Freedom to pursue educational & research opportunities; ?? Home-work-life balance; ?? The geographic-business community in which we operate ; ?? The pursuit of excellence; ?? Our contribution to society; ?? Creativity & innovation; ?? Teamwork & collaboration; ?? Career development, achievement & reward.

May 1, 2008

By Christopher McElman

Real-time mine management solutions have evolved over time from closed, proprietary solutions, to a "system of systems" that may include a wide variety of off-the-shelf components and technologies. Modular Mining Systems has embraced open standards for their NextGen products to bridge the technology gaps between these systems. However, the remaining logical gaps must be overcome, in order to achieve truly seamless integration between discrete systems. When dealing with volatile real-time management problems, the effectiveness of business process modeling and middle-ware can break down. Scientific principles of military command and control applied to mining domain help to achieve better alignment and reach the highest level of integration. The combination of open standards and off-the-shelf hardware and software with a deliberately structured command-and-control approach provides a clear evolutionary path from ad-hoc connected systems towards real-time management of a seamlessly integrated digital mine.

Oct 1, 2009

By E. Marcotte

"Technology developments and improvements are imperative to maintain a viable mineral processing industry. In order to achieve optimum implementation of technology in processing plants, safety conscious and efficient work forces are required. Effective management methods are required to prevent employee injuries, equipment or environmental damage and process losses. Good leadership also provides for employees to perform their work in the safest and most efficient manners to attain optimum recoveries of the valuable minerals and produce high quality mill products. Equipment and processes must be designed, operated and maintained as required to assure safe and efficient mineral processing.INTRODUCTIONThe Canadian mining industry must contend with many challenges to attain and maintain a competitive position in today's global market. Canadian Mineral Processors play a vital role in meeting the challenges and achieving optimum mineral productivity.Ongoing technology developments and improvements continue to be imperative to maintain a viable mineral processing industry. The efficient implementation of technology developments requires a safety conscious, skillful and productive work force.In addition to technical and human resources, challenges may also include governments, labour unions or environmental advocates who at times may appear to be misguided or unrealistic. Canadian Mineral Processors must not allow themselves to be overwhelmed by these apparent obstacles but must use their demonstrated ingenuity to achieve successful solutions.It should be recognized that the majority of the Canadian work force are, in fact, a potentially talented and skillful people with ambitions to excel. As leaders of people, we must provide the methodology, incentive and direction that will allow our work forces to realize their ambitions. If the potentials of our work forces are not recognized and leadership is not properly exercised much loss will occur. That is, safe effective and efficient work will not be achieved."

Jan 1, 1993

By J. Bhattacharya, S. K. Mukhopadhyay, S. K. Pal

"While time and again many authors have categorically stressed the restoration of the environment, very little effort has been made in the mineral industry to develop the economy of environmental control. There are many abatement procedures that search a maze of variants. Among them pricing environmental damage seems to be more logical and easily implementable.IntroductionMining as an operation has a severe impact on the Earth&apos;s natural resources. While economical environment control is much sought after, solutions are often varied and complex, and can differ in the problems of single or multiple mine sites.Determination of Optimum use LevelsIn “mining environmental control"" it is required to strike a balance to find optimum use levels. The solution is to find where the welfare benefits equal the cost involved to curb the degree of environmental damage (Fig . I) . In the mining industries this can be done by modifying the production/extraction process itself. For most pollutants, the marginal costs of control will exceed the benefits from further reduction of damage long before the zero pollution damage point is reached (Fig. I). From an economic perspective the optimal alteration of environment by mining would occur at z; pollution continues to be caused by ""zy"" control units, but it would be inefficient to pursue the redemption efforts further because the marginal cost involved would exceed marginal welfare benefits."

Jan 1, 1992