Search Documents

By Richard Shea

Morris-Shea, an Alabama-based deep foundation contractor, is installing foundation piles at the sites of North America's two largest liquefied natural gas (LNG) terminals currently under construction. The contractor has crews working at Venture Global's LNG lique- faction plant in Plaquemines Parish, Louisiana, as well as constructing foundations for the Cheniere Energy Stage 3 Liquefaction Project in Corpus Christi, Texas. This work includes installing ap- proximately 27,000 DeWaal drilled, full displacement, cast-in-place concrete piles to support seven new midscale LNG trains at Cheniere's Texas ter- minal. Deep foundation installation began at Venture Global's Plaquemines facility, located approximately 30 mi (50 km) south of New Orleans, with an initial phase of 24,000 piles. Plans for the Plaquemines LNG terminal include three loading berths on the Mississippi River and four LNG containment tanks. The facility will utilize new pretreatment com- pressors, liquefaction trains and on- site gas turbine power plants to maintain an annual LNG export capacity of nearly 20 million tons (18 million tonnes) per annum. The site's LNG trains are configured in 18 blocks. The contractor is installing piles through an initial 6-20 ft (1.8-6 m) of cement mixed improved soils, which provide a safe work plat- form for equipment to operate on the extremely weak native soils. Drilling continues through soft clay in the subsurface and tips into a stiff clay or dense sand layer. Production piles are drilled to depths up to 124 ft (38 m) below ground surface. The firm is working with engi- neering, procurement and construction contractor KZJV, a Kellogg Brown & Root and Zachry joint venture, at the Louisi- ana location. The foundation team mobilized at the Plaquemines site in May 2022, to install 16, 18 and 24 in (400, 450 and 600 mm) diameter test piles to depths of 90 and 120 ft (27 and 36 m). The piling contractor returned in September 2022, to start Phase 1 of the deep foundation project, beginning installation of production piles.

Apr 1, 2023

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Robert Thurner, Albin Norrman, Sami U. Raja

The West Link is a double track railway project currently under construction in Gothenburg, Sweden. The project includes the construction of 8 kms of track, 6 kms of which will be in tunnels. Beside several large excavations, three new stations will be built: Centralen, Haga and Korsvägen, all within the city of Gothenburg. The first construction phase of the project began in May 2018, and the finalization of the project is expected in 2026. The project is divided into five sections. Keller is involved in four of these contracts since the design & planning phase in 2018 assisting the special foundation works with various geotechnical techniques including Dry deep soil mixing (DDSM), jet grouting, rock grouting, uplift piles, sheet piling and rock dowels. The core idea behind successful collaboration has been to apply the right product for a location specific challenge which can help optimise costs & time for the project with a minimal environmental impact. Due to the extensive nature of the project, a team of experts from various locations around the world is helping design and execute various foundation technologies and providing solutions to the practical challenges in the project like working close to existing structures, rail lines, river etc.

May 1, 2022

By Clarissa Aguiar, Seok hyeon Chai, Thamer Yacoub, Sina Javankhoshdel

Sheet piles are used as an excavation support for soil retention. They are interlocked systems to form a wall for earth support along with anchors to provide an extra lateral support in excavations. The earth pressure against a sheet pile structure is not unique for each soil, but rather a function of soil-structure system. Movements of the structure with respect to the soil are primary factor in developing the pressure and thus the problem becomes indeterminate. In order to model a sheet pile wall for the analysis, structural element/interface can be used for the sheet pile. However, the use of the structural element with soil model alone is insufficient to simulate this soil-structure system as it fails to capture the slip condition between the sheet pile and the retained soil. In order to capture this slip condition, an interactive element can be used between sheet pile and soil to allow slip to occur. There have been many case studies where this method was used to analyze the response of the retained soil. Numerical studies have shown a good agreement with experimental results, but this stiffness is often not a well-known parameter, due to its complexity in nature of interactive behavior between soil and sheet pile walls. Also, many case studies are carried out with twodimensional analysis of the foundation, where three-dimensional analysis may be more suitable in some practical applications. In this paper, the interactive behavior of the element between sheet pile and soil is investigated with case studies for staged excavation using sheet piles and anchors. Then, investigation of a three-dimensional model is carried out by comparing with two-dimensional analysis.

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021

By Joshua C. Adams, Les Chernauskas, Edward L. Hajduk

"Drilled shafts are increasingly being used to support bridge and building foundations. Because these foundations usually carry very high design loads and often serve as non-redundant, single load carrying units, these foundation systems need a high level of quality control (QC) and quality assurance (QA) during construction. One such method for providing QC/QA is crosshole sonic logging (CSL) testing, in which ultrasonic signals sent across the drilled shaft concrete assess concrete quality.CSL testing is an effective tool to evaluate the integrity of the in-place drilled shaft concrete. While typically used to evaluate drilled shaft concrete after construction, CSL testing can also be used to evaluate drilled shaft repairs. This application can be difficult, given the variability of repair methods and material properties. CSL testing can also be adversely affected by the condition of the concrete/access tube bond, leading to false anomaly detection and/or inability to evaluate concrete integrity effectively. This phenomenon, called access tube debonding, is often located in upper portions of the drilled shafts where large changes in groundwater occur, such as within tidal zones.Two case histories showcase innovative uses of CSL testing to deal with consistent access tube debonding and to evaluate drilled shaft repairs.CSL OverviewCSL testing involves placing ultrasonic transmitters and receivers in access tubes installed in the drilled shafts prior to concrete placement. Concrete quality is assessed by examining the First Arrival Time (FAT) and relative energy of the signal sent between the transducers. If the distance between the access tubes is known, an apparent signal velocity (i.e., wave speed of the ultrasonic signal through the concrete) can also be determined and used to assess concrete quality.Common CSL testing practice consists of simultaneously raising the ultrasonic transmitter and receiver and recording the ultrasonic signals with respect to depth. This results in a 2D examination of the"

Jan 1, 2009

By T. G. Davies

The paper presents design equations for singly laterally loaded piles embedded in sand. These equations were obtained from a comprehensive nonlinear analysis of free and fixed head piles subjected to horizontal loads. The sand is modelled as an elastic-perfectly plastic material whose strength and stiffness are proportional to depth below ground level. The soil's response is described by means of a boundary element representation of the continuum while the pile itself is created as an elastic beam. Equations for the latter are derived directly from the Bernoulli-Euler theory and are coupled with those describing the non-linear soil response. The effects of bearing failure along the front, face of the pile, shear failure along its sides and tension failure at the back face are accounted for in the analysis. Simple equations are presented to describe both the elastic and inelastic responses. The only sol parameters required to use these equations are the angle of internal friction of the sand and a parameter characterizing the rate of increase of the sand's modulus with depth. The latter can be taken as equivalent to the modulus of subgrade reaction. The results of this analysis show that soil yielding is very significant at working load levels, resulting in substantial increase in bending moments and lateral deflection.

Jan 1, 2010

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Thomas J. Kennedy, Michael D. Bennett

The study of geotechnical history is well-established. Most geotechnical practitioners, teachers, and graduate students have some grasp of the origins of the field. However, this understanding often consists of a jumble of names and anecdotes. This paper discusses how a deeper comprehension of geotechnical history can benefit academia and practice alike and describes how the authors have begun a wide-ranging study of the subject. The paper reviews the dual-track methodology the authors have generated for the study, which consists of written articles about different works in geotechnical history and a database tracking how often pieces have been cited in geotechnical literature. The first technique has shed light on aspects of geotechnical history such as the connection of the Darwin family to the origins of geotechnical engineering, the St. Francis Dam failure of 1928, and the rivalry between theoreticians and practitioners in the early days of the field. The second has helped quantify subjects such as the outstanding contributions of Karl Terzaghi, the disagreements between Terzaghi and Donald Taylor, and the specialization of the field over time. The paper concludes by discussing the authors’ planned future work on geotechnical history.

Oct 1, 2022

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Jean Wehbe, Daniel C. Brahana

"The new Mercedes-Benz Stadium (MBS), home of the Atlanta Falcons, is part of a new era of stadium construction in the U.S. These new-age stadiums are larger and have more amenities than their predecessors. Many of the MBS’s features, including its innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are supported by drilled piers. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 ft (1.8 m and 1.9 m). Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings were used to support the more lightly loaded portions of the structure.The focus of this article is the construction aspects of the drilled pier foundations. Initially, a fairly extensive drilled pier load test program was performed. Load testing included a Statnamic compression test, two Osterberg Cell tests and two lateral tests. Production pier installation included over 3,800 linear ft (1,158.2 m) of earth excavation and over 1,350 linear ft (411.4 m) of hard rock excavation. The piers contain more than 6,600 cu yd (4,587.3 cu m) of concrete and 1,100 tons (998 tonnes) of reinforcing steel. Drilled pier installation took about 4.5 months. ABE Enterprises was the specialty foundation subcontractor and Bauer-Pileco was the equipment provider.Site and Subsurface ConditionsThe project site is in downtown Atlanta and was originally occupied by residential buildings. A portion of the site was later developed as a rail yard, and other areas contained light manufacturing, warehouses and other relatively light structures. For the past 15 to 20 years the site had been used for surface parking.Beneath a surficial layer of manmade fill, soil test borings at the site generally encountered residual soil, partially weathered rock and the parent bedrock. The bedrock at the site is highly variable, both in elevation and in hardness/quality. The depth to rock is reasonably uniform within the western two-thirds of the site at about 20 to 50 ft (6 to 15.2 m), with a few exceptions. In the eastern third of the site, the rock drops off dramatically to the north and east. In one mega column cap, there was almost 80 ft (24.3 m) in elevation difference. In two borings in the cap that were 20 ft (6.1 m) apart, the top of rock varied in elevation by 34 ft (10.3 m)"

Jan 1, 2016

By Yan Lap J. Kan

"A waterfront stabilization system consisting of Deep Soil Mixing (DSM) columns, vinyl sheet pile fascia, and concrete flood walls supported on shallow footings was designed and constructed for a high-density waterfront development in Northern California. The project site is underlain by soft, compressible organic soil locally known as Bay Mud that has been capped with loose sand and imported fill. The waterfront stabilization system constructed at the site mitigates liquefaction, consolidation settlement and seismic potential slope deformation along the waterfront; the system was designed to reduce lateral displacements to tolerable amounts for the proposed structures. This paper presents the general design methodologies, construction challenges and quality control of this waterfront stabilization system.INTRODUCTIONUrban development in Northern California is fueling innovations in geotechnical engineering as more complex sites are developed. ENGEO Incorporated introduced a deep soil mixing technology from Japan to the US and designed a waterfront stabilization system for a high density waterfront development project in Redwood City, California. The approximately 12½-acre project site, as shown on Fig. 1, is surrounded by water on three sides, with an inner marina at the center of the site.The project site is located in the seismically active San Francisco Bay Area in California. The San Andreas Fault, the Monte Vista-Shannon Fault, the Hayward Fault and the San Gregorio Fault are major active faults located within 25 miles of the site. Once a former marshland with a major slough until the late 1950s, the site was reclaimed by placing imported fill over the native compressible clay deposits, locally known as Bay Mud."

Jan 1, 2016

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Hayel M. El-Naggar, Mohamed Sobhi, Mamdouh M. Hamza, Marawan M. Shahien

"This paper presents the results of two lateral load tests on large bored piles in soft clay deposit for a major site in northern Egypt. The tests are carried out on 0.8 m diameter piles. One of the tests is carried out on the pile where the clay starts from the ground surface. The other test is carried out on a pile after surface improvement by replacing the top 1.50 m of the clay deposit by compacted granular soil. The results of the tests show the influence of the surface replacement layer on the lateral load versus lateral displacement relationships of the loaded pile. The results of the two tests are used to calibrate a 3D Finite Element Analysis model for the pile. The model is used to investigate the influence of the thickness and lateral extent of the surface replacement layer on the behavior of laterally loaded large bored piles.INTRODUCTIONLateral loads for piles are produced by seismic events, wind, wave action, ship impact, traffic, and land slide forces. The lateral resistance of a pile is controlled by the stiffness and the strength of the material of the pile and the soil surrounding the upper portion of the pile. In most situations, the soil surrounding the upper portion of the pile is too weak to sustain the design lateral loads. Thus there is a need to increase the lateral resistance of the pile or groups of piles. Such an increase may be achieved by either increase number of piles or increase pile diameter. Alternatively, an economic way to increase the lateral resistance is to improve the soil surrounding the upper portion of the pile (Rollins and Brown, 2011; Faro et al., 2015).Ground improvement has the ability to increase the lateral resistance of the pile by increasing the passive resistance of the soil surrounding the upper portion of the pile. The ground improvement techniques have the potential for being more cost-effective and reducing construction time. In spite of this fact, such techniques are rarely implemented in practice. Further, there are relatively few tests or records available in the literature to guide engineers in evaluating the actual effectiveness of this approach. In addition, there is no standard or methodology to aid engineers in designing increase of lateral resistance with surface ground improvement. There are specific improvement methods for each soil type, whether it is loose cohesionless soil or soft cohesive soil and these methods are provided by Michell (1981), Tershai and Juran (2000), ASCE (1997), and Rollins and Brown (2011). Furthermore, there are number of case histories that add a new hole in the sight, such as the cases provided by Brown et al. (1987, 1988), Mokwa and Duncan (2001), Rollins et al. (2005), Rollins and Cole (2006), Cole and Rollins (2006), Rollins, Snyder et al. (2010) , Rollins, Gerber, and Kwon (2010), Rollins and Nasr (2010), and Gerber et al. (2010)."

Jan 1, 2016

By S. P. Mukherjee, Smita Tung

"Piles are generally subjected to uplift in case of under ground and water front structures. Sometimes piles are also to resist uplift loads in transmission towers, dry rock, and so on. Experimental investigations of single piles and pile groups have been carried out using model hollow circular aluminum piles, having 25.4 mm outer diameter and lengths of 600 mm, 750 mm and 900 mm. Pile groups of 2?1 and 2?2 arrangements have been used in the experimental investigations. L/d ratio has been kept equal to 24, 30 and 36 in all the cases. All the single piles and pile groups have been tested under vertical uplift. Spacing between two piles in a group has been varied with respect to pile diameter such that spacing to diameter ratios of pile are 3, 4 and 5 in case of pile groups. An attempt has also been made to analyze those models of single piles and pile groups under vertical uplift by PLAXIS 3D software. Good analogy has been observed between the results of experimental and numerical studies. A parametric study has been carried out to observe the variation of ultimate uplift capacity of pile groups with spacing and depth of embedment. It is observed that for a particular embedment length of pile and a particular group arrangement the ultimate uplift capacity increases with increase of spacing. It is also investigated that for a particular spacing and particular group arrangement, the ultimate uplift capacity increases with increase of embedment depth. Those variations have also been presented with graphs which are generated considering non dimensional forms of parameters. The paper brings out change in pullout capacity of pile groups with spacing and embedment depth of piles.1. INTRODUCTIONPrediction of uplift capacity of single piles and especially of pile groups is one of the most interesting areas of research in geotechnical engineering. Pile foundations are frequently used to transmit the superstructure loads to deeper strata if the subsurface soil is of inadequate strength. The worst possible case may be considered to occur when all the piles in a group subjected to uplift. In cohesionless soils, the shaft resistance is an important source of pile capacity under axial loading, especially when the pile is subjected to uplift loading. Poulos and Davis (1980) recommended estimating the uplift capacity of piles as 2/3 of the downward shaft resistance. Later Ramasamy et al. (2004) indicated that the upward shaft resistance is significantly less than the downward shaft resistance. Some studies were conducted on the behavior of a single pile under uplift loads, such as those by Sowa (1970), Vesic (1970), Das and Seeley (1976), Levacher and Sieffert (1984), Rao and Venkatesh (1985), Chattopadhyay and Pise (1986), and Shanker et al. (2007). Das et al. (1976) conducted a model study to test the uplift capacity of single piles and pile groups buried in sand, and they also determined a relationship between the efficiency of a pile group and its spacing. Chattopadhyay and Pise (1986) proposed an analytical method for predicting the uplift capacity of piles embedded in sand and obtained reasonable agreement between experimental and theoretical results. Gaaver (2013) investigated experimentally that an upward displacement of about 1.4–2.5% of the pile diameter is required to attain the net uplift capacity for both single piles and pile groups. The uplift resistance of pile groups depends on the several variables like group size, shape, spacing to diameter ratio of piles, embedment depth to diameter ratio of piles, soil type and its density and soil-pile friction angle."

Jan 1, 2015