Search Documents

By Stephan Fisch, Franz-Werner Gerressen

"The use of cut-off-walls (COW) for the open pit coal mines has been used for decades. They have been used to reduce the negative hydraulic impact to the surrounding area caused by the open pit mining. The pile-guided trench cutting system is a worldwide unique technique, originally developed by the engineers of the mining companies themselves. It guarantees a continuous, joint free, COW during a continuous installation process. At this specific site in Welzow, this technique has been pushed to new limits in order to address the local lake region. Depth capability has been designed to about 430 ft (130m), proven are already depth of about 360 ft (110m) at a constant trench width of 39 inch (1000 mm). This project is approximately. 6.8 miles (11 km) long of COW, scheduled to be completed in 12 years period. About 2.05 miles (3.3km) have been installed, which is equivalent of about 3.5 Million ft² (330,000 m²). The system flushes special clay which forms a filter crust at the inner surface of the trench. Only natural clay resources used, in order to achieve the cut-off effect (colmation effect). The paper explains the installation process of the cut-off-wall as well as the equipment systems developed specifically for this project. After a successful start of the first phase of the project, the next step in the advancement of the equipment is already underway to enable the installation of greater depth to approximately 490 ft (150 m +) and beyond. The next generation equipment system is scheduled to start operation around 2018 INTRODUCTIONThis Serbian saying “Bóh je stworil Lužicu a cert je zaryl brunicu – God created Lusatia and the devil buried brown coal underneath it.” captures local communities’ ambivalence towards lignite.Lusatia is an almost entirely flat stretch of land between the Elbe and Neiße rivers dominated by glacial sands. On the surface, the heathland and woodland is hardly noteworthy. However, three large lignite mining regions, two in Brandenburg and one in Saxony, in the east part of Germany, divert the attention to underground level, down to depths of up to 120 meters. Here, seams crisscross the earth like ribbons. They were formed in the Tertiary around 17 million years ago.The mining of the lignite started almost 200 years ago. To enable open pit mining, a suitable dewatering system was required. At first, wells and drainage system were used. With the increasing demand to go deeper to enable full use of the existing resources with greater mining depth, a decision taken back in the 60th of the last century, the amount of water which had to be pumped increased dramatically. In peak times, approx. 1.57 Billion cubic yards per year (1.2 Billion m³/year) had to be pumped. This led to a lowering of the groundwater level for up to 230 ft (70 m), impacting the regional lake landscape. In order to reduce the influence on the water balance, and bring the water level back to pre1970th, a first development took place to implement the use of specific COW system to depth of about 147 ft (45m)."

Jan 1, 2017

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Daniel Ruffing, Charlie Krug

In recent years, the chain-style trencher has been proven a valuable tool for installing vertical walls on challenging sites where conventional methods may be less desirable. Like many tools, trenchers are most effective when used with the right application. Trenchers are commonly used for applications that could also be completed with conventional slurry trenching; low-permeability cutoff walls, collection trenches and permeable reactive barriers (PRBs). Drawing from a wealth of experience with conventional slurry trenching and the trencher, this paper compares and contrasts the technical considerations, treatability, installation, performance, and lessons learned for recent projects.

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By William F. Loftus

When high capacity diameter pipe piles are driven open-ended into the underlying bedrock, the material gathered inside the pipe often must be excavated to allow concrete to be placed within, in a clean environment. This paper discusses a method of dealing with this ?to be excavated material - the contaminated soil of the Harlem River in New York City, USA.?

Jan 1, 1996

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By C. W. Sheng

In this paper conventional construction procedure is briefly described for the installation of stone columns in soft ground in China. A viewpoint concerning the mechanism of ground improvement by use of stone columns is presented for discussion. Based on the information obtained from field measurement and observation three important problems relating to the construction and design of stone columns are discussed. Finally, a case history is given to show that short stone columns floating within the weak soil layers may in some instance be used to improve the weak strata of great thickness.

Jan 1, 2010

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By K. Oshima

In Japan, earthquakes are experienced frequently. Many buildings and structures in Japan are supported on pile foundations. For these pile foundations, the joint section between the piles and footing (hereinafter referred to as "Pile Head Joint"), where the load of the superstructure is transmitted to the ground through the piles, is important in both the design and construction of works particularly under seismic conditions. This paper discusses the state in which the force is transmitted to the Pile Head Joint, and introduces the basic construction of the Pile Head Joint, based on experimental investigation. Steel pipe piles

Jan 1, 2010

By Timothy C. Siegel

Drilled displacement piles (also known as augered cast-in-place displacement piles or augured, pressure grouted displacement piles) are installed by the displacement of soil and subsequent placement of fluid cement grout within the evacuated volume. Depending on the soil grain-size characteristics, soil behavior, in situ soil density, pile spacing, and pile diameter, the installation process can result in measurable densification and an increase in lateral stress. This paper examines the conditions prior to and following the installation of drilled displacement piles at sandy sites using the cone penetration test. The data support that the installation of drilled displacement piles results in a substantial increase in tip resistance.

Jan 1, 2007

By A. Ghorbani

The analysis of Combined Pile Raft Foundation (CPRF) is very complex due to involved interactions among components of CPRF system. Many researchers made efforts to develop sufficient methods including three dimensional finite element methods to compute these interactions. Since there are some restrictions and complexity in previous methods, in present study a new approach based on three dimensional finite difference methods is implemented to overcome some of these restrictions. The total and differential settlements of a centrifuge case study are computed using different numerical methods to show the performance of present numerical approach.

Jan 1, 2007

By Peter Arz

In the port of Hamburg a 650 m long quay wall was completed in mid-1985. The watertight wall consists of loadbearing steel buttress piles PSP 1012 which are up to 28 m long and infill interlocking sheet piles PZ 612. The construction method used for this quay wall, which included the simultaneous implementation of ground improvement measures, is the subject of this lecture. Originally, as is common practice, driving of the sheet piles had been envisaged. The composition of the subsoil, which consists of fill, clay, sand and boulder clay, is typical of the Hamburg region. In the upper layers (down to a depth of approx. 15 m), the subsoil is interspersed with debris from ancient civilisations but also dating from the war and post-war period (bomb craters filled with debris and demolition material).

Jan 1, 1987

By Ray Zelinski

Caltrans sponsored a research project in 1992 which incorporated proprietary and generic pile types. The piles were subjected to axial tensile/compressive loads in deep, soft soils. Descriptions of various pile types and systems, scenarios leading to the proposal to test the systems, and load test results were/will be provided by other presenters at this seminar. Therefore, this paper will focus on the issues surrounding use of test results and proprietary pile systems on Caltrans construction projects. The primary issues facing Caltrans during implementation are as follows: 1) producing pile cap designs for a range of pile types and loads; 2) providing construction specifications which allow fair competition among the system vendors, yet assure design and ultimate capacities; 3) Develop quality control standards for pile system materials and installation techniques which guarantee pile durability for static and dynamic loads; and 4) assure that foundations have adequate lateral capacity.

Jan 1, 1993

By Farhad Elmi

In this paper, a new procedure is used to find the bearing capacity of single piles and cone penetration resistance in soils. Although the procedure is mainly applicable to clay and sand using any plasticity model, this paper deals only with steady penetration in Sand. Cylindrical cavity expansion around the probe in a calibration chamber is modeled by finite element method using the HUJEUX elasto-plastic multi-mechanism model. The penetration resistance (qc) is related to cylindrical cavity expansion pressure limit (pL) using the method of Salgado et al. (1997). This procedure is tested using the results found in 3S/IMG calibration chamber. In this article the word "penetrometer" refers to both pile and cone.

Jan 1, 2002

By K. J. Yang

Based on investigations and model tests combined with pile foundation on Code compilation of drydocks, we present this report to give informations against uplift pressure of piles beneath floor of drydock. In a same kind of soil, we have got comparative tests results with single pile and pile group, and the latter was performed at different spacings, different embedded depths and different number of piles in the group. Having analyzed through the results, there are some new understandings of regularity about failure mechanism and uplifting capacity of single pile and pile group, as well as optimum embedded depth of pile foundation. The results of research approach to measured values of full-scale and model tests at home and abroad, it has been placed into the Design Code of Drydock in China (1985), and can give a reference to design of pile foundation at sea and on land under uplift loading.

Jan 1, 2010

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Shawn Downey

A helical pile with in-situ grouted shaft was used to underpin the existing slab of a large retail store in the Edmonton, Alberta Canada area. The existing structural slab did not have the capacity to support the increased load requirements. The design to upgrade the capacity specified a drilled shaft as the deep foundation to underpin a portion of the slab. A helical pile was quoted as an alternate and ultimately won the bid based on the advantages of the system. After an ASTM D1143 Quick Load Test confirmed the axial compression capacity, 723 helical piles with grouted shafts were installed in 3 weeks underpinning 40% of the 93,000 ft2 (8,660 m2) building.

Jan 1, 2003

By Yingcai Han

The dynamic behavior of pile foundations is investigated in both theory and practice. The computation method for vibration of pile foundations and DYNAN computer program are introduced comprehensively. With a model of non-reflective boundary between the near field and far field, the Novak's method of soil-pile interaction is improved. The dynamic analysis and design of foundation for a reciprocation compressor with driver power 15,000 HP are described to illustrate the computation method of soil-pile interaction. Different design options for the piles are compared to limit the vibration of foundation and produce a safe, economic system. The design with 16 - 0.9 m piles is adopted rather than that with 25-0.5 m piles, since the larger damping is provided by the piles with larger diameter. Both field and laboratory tests were carried out to investigate the soil properties including down hole seismic tests to provide soil shear wave velocities at different depths. The method and procedure used in this study can be applied to the design of pile foundations for tall buildings, bridges and offshore platform with soil-pile interaction under seismic, blast, sea wave and other dynamic loads.

Jan 1, 2002