Search Documents

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By Zachary Q. Maassen

The purpose of this paper is to highlight the environmental benefits of properly managing slurry waste as it is generated on site. The following projects will be used to illustrate the importance of proper onsite waste management. Project: Jet Grout Backflow Dewatering The goal was to dewater the backflow directly onsite to produce a dry, solid waste and reusable water. The backflow spoil was pumped directly to the dewatering system as it was generated. Utilizing mechanical separation equipment and flocculation polymer the waste volume was reduced by 44%. Due to the site footprint and high volumes, slurry waste removal and onsite processing were the only two feasible options. Onsite dewatering proved to be the environmentally beneficial option as it eliminated the need for slurry waste hauling and disposal. The benefits of utilizing a dewatering system are listed below: Project: Soil Mixing Spoil Recycling for Slurry Wall Construction In this application the spoils generated contain bentonite mud, cement mixture and organic ground soils. The goal of this project was to process the backflow mixture to recover reusable bentonite mud and separate the soil as a dry, stackable waste product. The treatment system replaced the traditional method of vacuum truck extraction and facility disposal. The environmental benefits of properly handling the backflow is a decrease in fresh water usage, bentonite additive reduction, and the reduction of CO2 emissions. The paper will consist of a project scope, technical equipment and process description, environmental impact reduction calculations and lessons learned for each project.

Jan 1, 2018

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By Edward J. McNamara

People in the real estate industry are fond of saying that the three most important features of a piece of property are, in order, location, location, and location. This is perhaps the reason that the owners of a well known high-end restaurant chain chose to spend $15 million dollars to renovate 5000 square feet of basement in a 22-story commercial building in the heart of New York City's Time Square. The goal was to create a music club with a stage area and dance floor with a mezzanine level surrounding the dance floor. In order to create the 50' x 40' dance floor and 20' x 40' stage area, 3 concrete columns were removed. New transfer girders were used to transfer the loads of these columns to new steel columns. For the mezzanine, nine columns had to be underpinned. All work continued while the restaurants, shops and offices above carried on business as usual. This paper details some of the means and methods utilized as well as the challenges faced by Underpinning & Foundation Constructors, Inc. in underpinning the columns and installing the new transfer steel.

Jan 1, 2000

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By John F. Spence

Ever since opening, the M25 motorway to the west of London has carried a rapidly increasing volume of traffic. The section of M25 between the junctions with the M3 and M4 motorways, which is in the near vicinity of Heathrow airport, is the most heavily trafficked section. Piling and ground treatment was required for motorway widening works over this route, which is 7 miles long. The foundation works were undertaken next to the live motorway and beneath the flightpath for aircraft landing and taking off at the airport. The paper describes the foundation construction techniques used, and the how the methods were affected by the live motorway and the height restrictions imposed by the airport. A unique method of piled retaining wall construction is also described.

Jan 1, 2007

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Dean E. Harris

The realignment of U.S. Highway 95 in Sandpoint, Idaho, is being designed on a site underlain by glaciolacustrine soil that includes very thick deposits of soft, sensitive clay to estimated depths of greater than 200 m. The highway realignment will include construction of numerous embankments, mechanically stabilized earth (MSE) retaining walls, and pile-supported bridges. The area of the proposed new highway corridor also includes existing historic and commercial buildings, a railroad, sensitive environmental areas, and economically vital tourism/recreational assets. The evaluation of pile axial capacity included the use of a variety of methods, including total stress, effective stress, and empirical methods using the results of piezocone soundings and conventional borehole and laboratory tests. These methods were used along with the findings from an instrumented static loading test to design the piled foundations for the bridges. A critical factor throughout the design of the pile foundations was controlling settlements to levels that could be tolerated by the bridges. Also, because of the proximity of the pile foundations to the existing structures and the proposed new embankments, the project has required careful consideration of the potential interaction between these elements. The analysis of piles also considered the potential for settlement of embankments, drag loads on the piles, and downdrag.

Jan 1, 2003

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By Timothy D. Stark

Jet grouting has increasingly become a ground improvement technology used to address seepage concerns and provide strength improvement to soils underlying dams. The technique of jet grouting uses high pressure/volume jet fluids to erode existing soil, evacuate some or most of the soil, and mix the remaining cuttings with cement slurry to form soilcrete. While considered a useful technology, this paper discusses some of the problems that can develop while jet grouting in or below a dam with an operational reservoir and seepage condition. Jet grouting experience at Tuttle Creek Dam indicates concerns with respect to ground fracture; spoil return, column diameter consistency, and homogeneity of resulting soilcrete. Recommendations are presented to increase monitoring of downhole parameters during jet grouting to better understand the downhole pressures and soil response during jet grouting.

Jan 1, 2012