Search Documents

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

By Anuj K. Singh, Shuvranshu Rout, Manos De

"Foundation for tracks of coke transfer car and dust extraction pipe was designed as series of isolated foundations spaced at 11.0m along length of coke oven battery resting on soil at depth of 2.5m. In one region the foundations are close to adjacent 12m deep underground junction house. Five foundations in this zone were constructed on backfilled soil without proper compaction instead of engineering soil fill or concrete fill. The foundations settled under loads and the supported frame structure tilted after equipment erection and during trials endangering the safety of the structure and equipment operation. The distorted structure had to be rectified in-situ by arresting settlement. In order to stabilize the foundation and supported structure the supporting soil had to be strengthened in situ without any dismantling, reconstruction and adverse effect to equipment operation. This paper presents the case study on the evaluation of defects for the foundation failure and analysis of the problem, proposed rectification of the situation by appropriate soil stabilization scheme, monitoring of the stabilization operations and verification of effectiveness of the rectification work by measurement of settlements. The implemented solution has ensured safety of the structure and equipment without any adverse impact on normal operation.INTRODUCTION AND BACKGROUNDNew Coke Oven Battery was being installed for an integrated Steel Plant. The hot coke from oven is pushed out after completion of coking process through a coke transfer car onto a hot coke receiving car. The coke transfer car runs on rail track parallel to the line of ovens forming the coke oven battery. One rail is supported on the structure of the operating platform of the battery and the second rail rests on independent structure of track beams. A large diameter pipe for extraction of the dust emitted during coke pushing operation is also supported on the same structure that supports the track beams. The entire structure rests on columns spaced at approximately 11.0m along the length of the battery. The columns transfer load to ground through individual foundations resting on competent subsoil strata.Two sets of foundations for the rail track beam support and dust extraction pipe support are adjacent to deep underground junction house of coke carrying conveyor. The depth of the pit for the junction house is 12m. The layout and arrangement of the foundations in this region around the junction house (JH-1) is shown in the “Figs. 1a, 1b”."

Jan 1, 2017

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By W. J. Kingwell

Where the equipment, technique and materials are available for the construction of large diameter rock socketted piles, this is frequently the most economical and environmentally acceptable method of supporting very large concentrated foundation loads in geoglogically appropriate areas. This paper outlines the current approaches in Australia to design and installation of large diameter rock socketted piles. The equipment and procedures described generally reflect those developed or used by Vibro-Pile (Aust.), a company which, while installing the usual range of driven and bored piles, specializes in the design and construction of large diameter rock socketted piles and possesses special expertise in drilling in high strength rock. A high capacity crane attached drill for large diameter drilling in rock is briefly described. Discussed in detail are the construction techniques employed and structural and geomechanical design methods adopted.

Jan 1, 1989

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By J. Hartikainen

19 papers were allocated to this session by the paper classification committee, 8 related to bored piles, 5 to continuous flight auger piles (CFA piles), 3 to slurry trenches, 2 to both bored piles and slurry trenches, one of them also dealing with root piles. There were no papers dealing with root piles only, as root filling is a different technique. One paper concerns sheet piling (Table 1). Table 1. Papers for session 1: Recent Technological Developments in Deep Foundations with Soil Excavation. [ ] Table 2. Classification of pile type in Belgium - van Impe W.F. /10/. [ ] Trends in piling Trends in piling in Central Europe were studied by van Impe for his brilliant lecture to the Finnish Civil Engineering Society. He claimed that bored piling is on the decrease and CFA pilling on the increase (Table 2). Thus the numbers of papers presented here do not conform to recent developments or trends. The papers submitted arc of course influenced largely by the fact, observable in Table 3, that bored piling is

Jan 1, 1994

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989