Search Documents

By Brandon Buschmeier, Frederic Masse

"Inclusions are a type of ground improvement that provide an improvement of a soil mass by insertion of a material with better characteristics than the surrounding soils. There are primarily two types of inclusions: “Soft” inclusions which are constructed of granular material (Stone Columns, Rammed Aggregate Piers, VibroPiers...), and “rigid” inclusions which are constructed of grout inserted with or without pressure (VibroConcrete Columns, Controlled Modulus Columns, Soil Mixing Columns).While the central principle of the inclusions is similar (i.e., overall improvement of characteristics of the soil mass below the structure), the load transfer mechanism is radically different for each technique. Therefore, the applicable design methodology is specific to the type of inclusions and there exists no universal method of design which spans across all inclusions.This paper will present an in-depth comparison between the standard design methods used for “soft” granular-type inclusions (Priebe modified, Balaam & Booker, Goughnour & Bayuk...) and the methods used for “rigid” inclusions which mainly rely on finite element analysis. The paper will explain why the design for soft inclusion methods cannot be applied to rigid inclusions and vice-versa. Each design method will be reviewed in detail to better emphasize its limitations and advantages.Two case histories will also be presented; one for each type of inclusions in order to illustrate the concepts developed in the first part of the paper.1 INTRODUCTION1.1 GENERAL OVERVIEW OF GROUND IMPROVEMENT WITH INCLUSIONSThe use of ground improvement methods to provide the appropriate amount of foundation support is a growing and constantly evolving industry. Traditional structural foundation methods including ‘shallow’ and ‘deep’ foundations do not adequately address the wide range of settlement tolerances, soil conditions, and loading considerations inherent to each unique potential project. In some instances, ‘shallow’ foundation solutions are simply not feasible due to soil and loading constraints. Furthermore, ‘deep’ foundation solutions are used to ‘bridge’ the soft compressible soils, ensuring that the entirety of the load in the structure is transmitted through individual elements into competent layers below the ground surface (bedrock, dense residual soils). Highly concentrated structural loads are transferred into the individual elements by means of direct contact requiring the use of structurally rigid surficial components (structural slabs, grade beams, and pile caps).Ground improvement bridges the gap between these two traditional methods, offering adequate foundation support while using more costeffective techniques and design methodologies. Inclusions are a type of ground improvement used to provide a reinforcement of the soil mass through the vertical insertion of a material with better characteristics than the surrounding soils. Much like deep foundations, inclusions are installed through soil layers with high compressibility and/or low bearing capacity and terminated in a suitable bearing stratum. However, unlike deep foundations, ground improvement inclusions rely on a distribution of load between the soil and the inclusions. By doing so, some of the structural load is applied directly to the soil in a proportion equal to its bearing capacity and compressibility limits, while the rest of the load is shed into the vertical inclusions down to the bearing stratum. Load sharing is a critical aspect in the performance and design of the various ground improvement methods."

Jan 1, 2015

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By Sumit Kumar Biswas, Moyukh De, Sibapriya Mukherjee

"The piles often are also subjected to lateral (horizontal) forces and moments. In fact, there are some structures where the primary function of piles is to transfer lateral loads to the ground. Proper analysis of laterally loaded piles is very important to the geotechnical and civil engineering profession.In the present investigation an experimental study has been carried out with free head short model cast iron hollow piles of outer diameter of 24 mm and L/d ratios of 8, 10, and 15. The experimental results have been supplemented by numerical techniques using PLAXIS-3D Foundation version 2.1 software. The results have been found to agree reasonably well with the experimental results. Further finite difference approach has been adoptedto reduce the computational time and to calculate the coefficient of modulus of subgrade reaction (?h) from the load- deflection data obtained from PLAXIS output at different pile depths. The parametric study has been extended for the non-dimensional form defined as flexibility ratio (F.R.),where ?h, L, Ep and Ip are the coefficient of modulus of sub-grade reaction, the embeddedlength of model pile, elastic modulus of pile material and the moment of inertia of model pile about the central axis respectively).The variation of coefficient of horizontal modulus of sub-grade reaction (?h) has been studied with respect to the following parameters for homogeneous soil system: relative density andL/d ratio. It has been found that the logarithm of flexibility ratio increases with increase inrelative density and increase inL/d Ratio. The values of ?h obtained by the proposed method have been, found to be close to the numerical results.As output of this research, graphs have been generated in respect of different parametric variations to gain an insight into behavior of piles under lateral load for short piles."

Jan 1, 2015

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By J. -L. Briaud

This presentation shows the results of laboratory and field tests to date for the NCHRP project entitled "Downdrag on Bitumen-coated Piles". This project required to test a variety of bitumens in the laboratory to determine their properties and then to establish a field testing program to verify the bitumens effectiveness. Figure 1 shows an organizational chart that gives an overview of the agencies involved in the project. The first part describes the laboratory testing program in which bitumen samples of various types were obtained from a variety of manufacturers. Initially, classification tests were performed to verify the manufacturers' specifications. Additional tests were then developed and performed to determine the bitumens behavior under the various conditions that they may be exposed to in the field. The test results were analyzed and their usefulness for design purposes were determined. The test results are presented in either graphical or tabular form. The second part describes the field testing program which was designed to test the effectiveness of various bitumens under a wide range of soil, temperature, and construction conditions. The first site was in Edmonton, Alberta, Canada, where a construction project was to take place in the winter of 1989-90. This was ideal for the cold temperature extreme that was needed. The soil conditions were conducive to downdrag problems: an embankment placed over soft clay underlain by dense sand resulting in end-bearing piles. The other site was in New Orleans, Louisiana. The part of the project involving this downdrag study was to be carried out in the summer of 1990. The hot summer temperatures and extremely soft soil conditions (resulting in friction piles) gave the other extreme needed for this study. Each site is discussed in

Jan 1, 1991

By Madhu. P, Srinivas. K

Measurement of thermal properties like thermal conductivity, thermal resistivity, heat capacity and thermal diffusivity for materials, it plays a crucial role in a wide range of various civil and electrical engineering projects, and many field applications like building’s basement, power generation, underneath soil heating, wastes from nuclear as well as thermal plants, and buried cables. Thermal conductivity of soil depends upon various geotechnical parameters such as type of soil, moisture content, particle size distribution, density, and compaction characteristics. Earlier studies, the measurement of thermal conductivity of soil by incorporating the heat source methods. Thereby expensive and time taken to conduct in laboratory as well as field measurements. The thermal conductivity is determined by fabricated probe and used in this work. Fabricated probe was calibrated with glycerin. The thermal conductivity of the soil increases as the water content and density increase because these factors are majorly influencing and water has a higher thermal conductivity than soil minerals, and grain to grain contact increases as density increases. therefore, Thermal conductivity is higher in coarser soils than in finer soils. The details regarding of this work as explained in this paper.

Sep 1, 2022

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By Spencer Ness, Yazen Khasawneh, William Tjaden, Mohammad Nassim

The evaluation of long-term performance of the wind turbine structures is essential in lowering the Levelized Cost of Electricity (LCOE) from wind sources. The required maintenance of the wind turbine foundation during the design-life time of the wind turbine may result in escalated cost, if not properly evaluated during the planning and designing phases. The degradation of the foundation soils’ stiffness due to the accumulation small plastic strains resulting from normal and/or extreme operating cyclic loading may result in escalating the O&M cost. The foundation’s stiffness degradation will result in a shift of the wind turbine system natural frequency, which may result in amplifying the vibrations generated at the hub. The anticipated shift of the wind turbine system natural frequency during the design-life time should be investigated through numerical simulations of the anticipated dynamic loading utilizing soil constitutive models that are capable of capturing the foundation stiffness degradation due to the accumulation of such small plastic strains. This study presents the validation of an element model that will be used to evaluate the performance of existing and/or proposed constitutive model.

Oct 1, 2022

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

Jan 1, 2002

By Murray Gamble

A new type of groundwater cutoff wall has been developed at the University of Waterloo. The Waterloo Barrier? is a steel sheet piling system that incorporates a sealable cavity at each interlocking joint. In order to prevent leakage through the joints, the sealable cavity is flushed clean and injected with sealant after the installation of the piling. The installation and sealing procedures of the Waterloo Barrier? system allow for a high degree of quality control resulting in a very low permeability cutoff wall. Based upon field installations, the bulk wall hydraulic conductivity of the Waterloo Barrier? ranges from 10-8 to 10-10 cm/sec. Recent case histories are presented in which Waterloo Barrier? vertical cutoff walls have been used to prevent the off-site migration of contaminated groundwater or soil gases. In some instances, the Waterloo Barrier? system was used in combinations of applications such as preventing the migration of contaminants, redirecting the flow of groundwater, providing structural shoring for soil excavation and aiding in site de-watering processes.

Jan 1, 1997

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Bao K. Le, Khang T. Truong, Masaki Kitazume, Toru Kobayshi, Long P. Le, Tanaka Hitoshi, Makoto Kamimura, Hoang-Hung Tran-Nguyen

"Earth levees constructed using dredged materials taken from a river along an earth levee have annually damaged in the Mekong Delta due to high void spacing in earth levees and floodwater. Sliding and internal erosion due to floodwater or piping are two key factors causing earth levees’ failures. This study proposed to apply Deep Mixing Method (DMM) to reinforce earth levees in the Mekong Delta, Vietnam. The DMM creates a soil cement wall or soilcrete wall having better engineering properties such as higher strength and low hydraulic conductivity than those of the in-situ soils. The DMM can be applied to reinforce earth levees with limit additional materials that provinces in the Mekong Delta are difficult to supply. The study investigates capacity of the DMM to reinforce earth levees in the Mekong Delta, Vietnam against annual floods. Seepage and slope stability analyses under various conditions were performed with various scenarios of earth levee’s body. The analysis results indicate that the DMM can create a wall that cuts off piping across earth levee significantly and can improve stability against deep sliding due to rapid drawdown of the floodwater.INTRODUCTIONThe Mekong Delta produces agriculture products of 50% of the whole country even though the Mekong Delta has an agriculture area of 30% of the country (Wikipedia 2014). Rice is the main product for the domestic demand and export. This is the main reason why the local people want to cultivate rice 3 times per year to increase the total rice product for export. To do that, the local provinces have constructed earth levees surrounding each area of 100-200-hectare against annual floods to protect rice fields, and farmers can grow rice in the whole year. There are thousands of kilometers long earth levees in the Mekong Delta, and the local governments have spent millions of US dollars to repair and to maintain their earth levees yearly (reports of Dong Thap province 2012; 2014).Earth levees in the Mekong Delta have often failed in flood seasons (e.g., from August to December), especially in Dong Thap and An Giang provinces – the two provinces confronting directly the annual floods from the Mekong River when the floods reach the Vietnam land. The main failure of earth levees is piping, and then causing collapse of some section of an earth levee. An earth levee was usually constructed by piling up dredged materials along a river with minimum compaction. Subsequently, floodwater flows through connected void spacing and washes out soil particles in the body of an earth levee slowly to create piping. Annual wet-dry cycles make the top clay layer swelling and shrinking to form cracks that can store rainwater to trigger sliding (whitlow 2001; Ton That Vinh 2003)."

Jan 1, 2015

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By Thomas Trochalides

Newtown Creek Water Pollution Control Plant in Brooklyn, NY is the largest of 14 Water Pollution Control Plants in New York City. It services over 1 million people with a current processing capacity of 310 million gallons daily. Upgrades to the plant have been underway since 1998. This paper details the foundation elements installed in three separate contracts during 2009: NC-41F, NC-36G, and NC-47G. The elements are Concrete-Filled Pipe Piles, H-Piles, Steel Sheet Piling, Secant Walls, Drilled Caissons, and High Capacity Micropiles. Soils on the site consist of fill over organic silty clay and silty sand. Beneath the organic layers lie lake sand and varved silt and clay, sitting atop glacial till and rock. Due to Federal Mandates, certain plant capacity and secondary treatment requirements had to be met by specific dates. Failure to meet the requirements would have an adverse affect on the NYC areas being serviced. Further complicating the project, the existing plant operations had to be maintained throughout the entire construction phase. To accommodate the constraints of the project, new specialty equipment and several key redesigns were used to maintain construction schedules

Jan 1, 2010

By Steve Davidow, Ashely E. Evans, Peter M. Kandaris

"Annually thousands of deep foundations are constructed across North America supporting high voltage transmission line structures. However, a recent state of the practice survey by the Deep Foundation Institutes’ Electric Power Systems Foundation Working Group discovered that the electric power utility industry lacks consistent foundation design guidelines. The survey identified a wide variability in design assumptions, a minimal understanding of risk based analysis, and a need to standardize design methodologies. This paper summarizes the state of practice in electric system foundation design and proposes a framework for risk-based foundation design by accounting for uncertainty from both loads and resistances. Loads derived from electric system codes do not necessarily provide a compatible level of reliability for the design of foundations, as they are a mixture of probabilistic and deterministic values. Load uncertainty is derived from variability in weather conditions, structural models and material properties, typically accounted for by code derived overload factors. Resistance uncertainty arises from variability in natural soil properties, resistance models, subsurface construction techniques, material sampling methods, and limited observations. A consistent methodology is offered relating nominal resistance capacity (strength) to structure loads and service state criteria. Discussion also includes the need for risk-based assessments to account for non-structure load influences (fluvial loads, scour ground loss, liquefaction, etc.).INTRODUCTIONNearly 40 years ago the Electric Power Research Institute (EPRI) embarked on a major research effort to optimize reliability and economics of transmission line foundation design. Strategies focused on improvements in design models, site characterization, exploration strategies and testing to reduce uncertainty and variance in analysis. Transmission line engineers realized that safety and reliability advancements in design based on probabilistic approaches, with a focus on the unique nature of transmission line, could better control risk and cost.Some transmission line professionals took full advantage of these advancements, particularly where research led to improved software and models. Yet, even after two decades of extensive research, by 1995 the industry still had made little progress in changing design habits. The majority of designers were still characterizing sites via deterministic methods, using loads that may or may not relate to a consistent probability of occurrence, and applying a traditional global factor of safety approach (Phoon, et al. 1995). The following two decades have seen even greater developments in software and reliability-based analysis methods, but old habits seem to die hard as recent surveys show less than half of design professional quantitatively assess risk in their design process."

Jan 1, 2017

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.