Search Documents

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By Ambarish Ghosh, Chitralekha Ghatak, Tanumaya Mitra, Tarun Sengupta, Sajib Das, Sankar Kumar Nath

"Currently construction of important structures like bridges, flyovers and high rise buildings in and around Kolkata are in full swing. These structures have mostly pile or well foundations. The design methodology and construction techniques are being employed keeping in view both the safety and economy of the project. The data presented in this investigation have been taken from Geotechnical Investigation report of Component B in connection with construction of Extradosed Cable Stayed Bridge over River Hooghly in Hooghly and Nadia district of West Bengal, India. The investigation site is located within close proximity of Eocene Hinge Zone which is being taken as the principal contributor of Earthquakes in and around Kolkata. Considering the importance of the project detailed and exhaustive geotechnical investigation has been carried out and site specific response spectra have been generated for analysis and design of the bridge. This paper presents site specific response spectra, liquefaction analysis and comparison of lateral load carrying capacity of pile using Winkler approach and IS 2911 guidelines.INTRODUCTIONPile foundations are used to transfer the load of the super structure through soft soil deposit to deeper bearing stratum by means of skin friction or end bearing or both. Pile foundations are regarded as a safe alternative for supporting structures in seismic areas and have been used for this purpose in non-liquefying as well as liquefying soils. But their design in case of potentially liquefiable soil is quite different from that of non liquefiable soil. In liquefiable soil the progressive buildup of excess pore water pressure will cause stiffness degradation and loss of strength which in turn will induce additional shear force and bending moment in the pile. The mechanism of pile behavior in liquefying soil has been investigated by several investigators in the recent years based on observations of pile performance during earthquakes and studies in the centrifuge and Shake Table tests. Exhaustive geotechnical investigation has been carried out along the proposed alignment of the Extradosed Cable Stayed Bridge i.e., along Baropara, Bansberia ROB, Ishwar Gupta Bridge, Saraswati River to collect disturbed as well as undisturbed soil sample, to develop average soil profile and to determine the design parameters. The proposed project site is very close to Eocene Hinge Zone, which is basically a strike slip fault, capable of generating an earthquake of Mw 6.7. Thus it is evident that the proposed Bridge needs to be designed considering the adverse geo-hydrological condition as well as the earthquake aspects needing special attention following the state-of-the-art technology as guided by relevant codes and published literatures. Considering the soil profile of these locations ground response analysis has been carried out using equivalent linear method to determine the site amplification. Site specific response spectra have been developed for the four zones and zone factors have been determined. The computed zone factors are 0.198g, 0.195g, 0.195g and 0.20g for the four zones respectively, much higher than the zone factor 0.16g, which is for zone III, as stipulated in IS 1893:2002."

Jan 1, 2015

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017

By Stephen Buttling

The construction of a water treatment plant in Dandenong, Victoria, required detention tanks and a pumping well. The design provided by the Engineer used conventional rectangular cast-in-situ reinforced concrete walls within a sheet piled cofferdam. It was decided to construct the tank and shaft using the diaphragm walling technique as an alternative and, for the shaft in particular, this involved a “circular wall”. Except where cutters are used, joints in diaphragm walls have to be made between colinear panels, with waterproofing provided by dumb-bell water stops held within trapezoidal forms. This means that the circle has to be approximated by a number of straight sides, which in this case was twelve. The requirement was to design the reinforcement for the strange shaped panels. Finite element analysis was used, in the first stage using an axisymmetric model to determine the profile of lateral earth pressures with depth. In the second stage a horizontal slice was modelled, without gravity which normally operates from the top to the bottom of the page. By considering appropriate possible earth pressures at different depths, a range of bending moments was calculated, which was used by the structural engineers to design the rebar. The tanks were successfully constructed, and inclinometers were installed in both the tank and the shaft. Measured deflection profiles show that the design was moderately conservative.

Nov 1, 2022

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Anahita Modiriasari, Benjamin S. Rivers

Measurement while drilling (MWD) is a subsurface exploration technique associated with real-time and continuous monitoring and recording of drilling data during the drilling process. This technique can be used for underground investigations to differentiate ground strata, detect the presence of fractures and voids, and evaluate geological features and mechanical properties of geomaterial. When MWD is used for geotechnical investigations, it can improve site characterization, identify variable conditions, improve design and construction, lead to shorter project delivery times, reduce the cost and risks associated with limited subsurface data and geotechnical uncertainties, and maximum return-on-investment. Given these benefits, MWD is gaining attention among transportation agencies and the geotechnical industry. Federal Highway Administration’s (FHWA’s) innovation deployment program “Every Day Counts (EDC-5)” includes the implementation of Advanced Geotechnical Methods in Exploration (A-GaME), which aims to implement effective, underutilized subsurface exploration methods, including MWD, in U.S. practice. This paper provides an overview of the MWD technology for geotechnical site investigations and presents a case history where MWD was employed to design deep foundation for the construction of a building in Massachusetts. The advantages of this technology for risk reduction and project cost and time saving are also discussed.

Oct 1, 2022

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Stefan Larsson, Sadek Baker, Razvan Ignat

"This paper describes the execution of two full-scale field tests where a braced steel sheet pile wall interacting with rows of overlapping dry deep mixing columns was first excavated and then loaded to failure. The aim of the tests is to provide insight of the performance of dry deep mixing column rows located in passive zone and interacting with a retaining structure. The column rows were installed perpendicular to the sheet pile walls with two different area ratios, i.e. different distanced between the column rows. Both tests were extensively instrumented with inclinometers, pore pressure transducers, bellow-hoses, earth pressure gauges and strain gauges mounted on the struts. Results of the performedtests will serve as development of design methods for excavation support with columns.INTRODUCTIONDry deep mixing has been used with good results to strengthen the soil when excavations are to be performed in locations with thick soft clay deposits. An application that has increased in recent years is to install columns on the passive side of the retaining structure. Columns can be installed in different patterns but rows, grids or blocks are the most common arrangement. The use of column type ground improvement installed on the passive side of a retaining structure has been documented for a few field cases, Tanaka (1993), O’Rourke et al. (1997b), O’Rourke and McGinn (2006), Ou et al. (2008). By improving the soil on the passive zone, the passive earth pressure in front of the retaining structure is increased. This has proven to reduce the excavation induced deflections behind the retaining structure, reduce the structural forces (bending moment in the retaining structure, strut and anchor forces) and improve the safety against basal heave failure. The main focus of the conducted measurements within these cases has been on recording deflections and structural forces on the retaining structure and there is very little documentation available of the stress-strain behavior of the improved soil acting on the passive side of the retaining structure.Two full-scale tests of braced steel sheet pile walls interacting with rows of overlapping dry deep mixing columns were first excavated and then loaded to failure was conducted during the spring-summer of 2014. This paper briefly describes the test set up, instrumentation, test procedure and some selected results from one of the conducted tests."

Jan 1, 2015

By Peter Cali, David Yang, Rakshya Shrestha, Ralph Griffin, Sushil Kafle, Motoji Watanabe

"As a part of the ‘US Army Corps of Engineers - New Orleans to Venice, Louisiana Hurricane Protection Project’, deep mixing ground improvement was designed to reinforce the soft ground for the emergency repair of a 7297-foot (2,224 m) long section of the Mississippi River West Bank levee in Buras Levee District under the contract ‘Emergency Levee Repairs – Contract P-17A, Plaquemines Parish, Louisiana’. The ground improvement utilizes a series of soil-cement panels oriented in the transverse direction of the levee. Each soil-cement panel consists of overlapped columns installed by the deep mixing method (DMM). DMM is performed from the existing top of levee and extended to competent stratum at depths varying from 26 feet (7.9 m) to 47 feet (14.3 m) below the working platform. The main purpose of the DMM panels is to provide shear resistance to the levee against lateral loads at high flood water condition. The DMM panels support the additional vertical load created by the increased height of the levee for hurricane protection and control the long-term settlement of the remediated levee, which might otherwise occur due to the compression of soft foundation soils. The total amount of DMM treatment is approximately 54,000 cubic yards (41,500 cubic meters). This paper reviews the project background, subsurface soil conditions and presents the design, construction and quality control of the deep mixing work for this levee repair project.INTRODUCTIONIn August 2005, Hurricane Katrina caused major damage to the federal and non-federal flood control projects in southeast Louisiana. In September 2005, Hurricane Rita caused further damage to this flood protection system. In an effort to minimize further damage and to enhance the protection level, certain non-federal levees located on the west bank of the Mississippi river in Plaquemines Parish, Louisiana were incorporated into the New Orleans to Venice Hurricane Protection project by the US Army Corps of Engineers (USACE). DMM techniques were then utilized by the USACE in several of these emergency projects and in many medium sized projects between 2006 and 2010 (Bruce et al. 2012). This project (called P-17A hereafter) which forms a part of this protection system is executed under the contract Emergency Levee Repairs, Contract P-17A. This is one of the largest projects of the USACE after LPV- 111. The huge LPV-111 project (5.5 miles (8.9 km) of levee) treated by DMM), the largest DMM project ever conducted outside Japan, began in 2010 and was completed in 2012 (Cali et al. 2012, Bruce et al. 2012).DMM is utilized at P-17A to construct a series of soil-cement panels oriented in the transverse direction of the existing levee to provide shear resistance to the levee against the lateral load during high flood water condition. The project extends 7297-foot (2,224 m) along the West Bank Levee of the Mississippi River in the Buras district of Louisiana, parallel to Louisiana Highway 23 (LA-23) as shown in Figure 1. It is located approximately 60 miles (96 km) south-east of downtown New Orleans."

Jan 1, 2015

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Joseph A. Sopko

The first documented procedures for designing frozen earth structures are over 50 years old, implemented long before the introduction of the Finite Element Method (FEM). Since that time, the development of three-dimensional models has made the traditional and often over-conservative methods relatively obsolete. This paper discusses a new approach that is largely dependent on the analysis of internal stresses with the frozen structure and comparison to frozen soil laboratory tests. A specific design process is discussed related to initial field investigation, laboratory testing, structural and thermal analysis, and performance monitoring. The design results are compared to case histories in the field that verify the procedure. BACKGROUND One of the first documented methods to designing frozen earth retaining structures was by Sangar (1968). Methodical refinements were published by (Harris 1995) and published by the International Symposium on Ground Freezing in 2002 (Andersland et al. 1991). The structural design or thickness of the frozen mass was based on the unconfined compressive strength of the frozen soils. Two simple equations for determining the thickness of a frozen shaft are shown in Fig. 1 and the first two equations below.

Jan 1, 2019