Search Documents

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By William M. Tanner, Daniel C. Brahana

"A drilled pier foundation was originally designed to support the proposed G. Wayne Clough Undergraduate Learning Commons on the campus of Georgia Tech in Atlanta, GA. Reflective of the site geology, the original drilled pier foundation was divided into a Northern and Southern portion with an allowable end bearing capacity of 60 ksf and 100 ksf, respectively. After initial pricing on the original design, several value engineering options were submitted that featured changes to the original design capacity and construction method. The project team selected the value engineering option that involved conducting an Osterberg Load Cell test to assess end bearing of the site bedrock and skin friction. Results of the Osterberg Load Cell test justified increasing the allowable end bearing capacity of the site bedrock to 100 ksf in the Northern portion and 125 ksf in the Southern portion. Considering the final foundation design and Osterberg Load Cell test program, a net savings of approximately $259,000, or approximately 34%, was obtained over the original design.Project BackgroundThe G. Wayne Clough Undergraduate Learning Commons (CULC) is a 5-story academic building on the Georgia Tech campus in Atlanta, Georgia. The CULC was completed in 2011 and consists of a concrete frame structure supported on a drilled pier foundation.After pricing of the original drilled pier foundation design, several value engineering (VE) analyses were performed by the foundation contractor in an effort to demonstrate the potential for a reduced foundation cost. The VE analyses focused on variations in design assumptions, as well as construction techniques. This paper presents a case study that demonstrates how the value engineering process can be used to reduce foundation costs.Site Investigation and Subsurface ConditionsThe CULC building site is located within the Southern Piedmont Physiographic Province, an area underlain by metamorphic and igneous rocks. McConnell and Abrams (1984) indicate that the site is located at the boundary between two distinct geologic formations. The Northern portion of the site is underlain by the Wahoo Creek Formation while the Southern portion of the site is underlain by the Stonewall Formation. The following paragraphs briefly describe the geotechnical investigations performed by the project geotechnical engineer (GE) for the CULC."

Jan 1, 2015

By Michael Gebman, Jack Gerwick

"With the opening of the new San Francisco-Oakland Bay Bridge East Span, the former bridge and its caisson foundations are being demolished. Caisson foundations are in the path of a future shipping channel and therefore need removal down to the mudline 50 ft below water (MLLW). For the first caisson to be removed (E3) a mechanical demolition was performed above the waterline and an implosion was done for the remaining caisson down to mudline. Mechanical demolition consisted of excavators operating from either on top of the caisson, from work platforms or from barges. The demolition was implemented on a trial basis with a successful implosion on November 14, 2015. The work was conducted in an environmentally sensitive area, with measures taken to protect fish, marine mammals and birds. This demolition technique was cost effective, faster to execute, and had a better environmental impact then an alternative option. The demolition, measures implemented to protect the environment, outcome, and lessons learned are presented.INTRODUCTIONThe California Department of Transportation needed a cost effective and environmentally friendly solution for removal of the remaining San Francisco-Oakland Bay Bridge (former East Span) caisson foundations, starting with caisson E3. This was necessary to clear a future shipping channel. One option was to construct a steel cofferdam around the caisson to allow demolition in the dry down to the mudline. This option would take years to complete, be cost prohibitive, and its noise would disrupt aquatic life and birds throughout the cofferdam construction and demolition. An alternative option was implemented on a trial basis to conduct a mechanical demolition of the caisson above waterline along with an implosion of the remaining caisson down to mudline. This had the clear advantage as a cofferdam was not needed, and the demolition project duration would be approximately 6 months, instead of several years for the cofferdam option. The potential impact on aquatic life and birds from the implosion was a concern, as the location is environmentally sensitive; however, measures were implemented to minimize these impacts. As presented in this paper, this demolition option was implemented on a trial basis for Caisson E3. The technique succeeded and will now be used on the remaining caissons.BACKGROUND INFO ON CAISSON E3The reinforced concrete Caisson E3 is the largest caisson which supported the former East Span of the Bay Bridge. It was constructed in 1934, with the Bay Bridge opening in 1936. Figure 1 shows the project location. The caisson had a cell arrangement of 7 x 2 above the mudline. Below mudline, the caisson had a cell arrangement of 9 x 4. A structural transition was made between the 7 x 2 and 9 x 4 cell arrangements with buttress walls. All cells were flooded, as underwater openings were included in the original caisson walls to equalize the hydrostatic pressure. Figure 2 shows the caisson layout with limits for mechanical demolition and for the implosion."

Jan 1, 2016

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019

By M. Meckkey El Sharnouby

In this paper, the results of full-scale field testing of reinforced helical pulldown micropiles (RG-HSP) installed in clayey till soils and resting on sandy soils are presented. Piles were tested under monotonic and two way cyclic lateral loadings. Effect of different loading setups on the results is demonstrated. The factors affecting the piles' performance are discussed. It was found that under monotonic loading the piles were able to sustain displacement up to 50% of the grout shaft diameter. Under low cyclic loading levels, the piles did not suffer degradation in the performance. Also, the degradation rate during cyclic loading increased with the increase of the load level. The experimental results show that the reinforced helical pulldown micropile is a reliable foundation option for lateral monotonic and cyclic loading applications.

Jan 1, 2011

By Michael A. McNicholas

"Deep foundations utilize the varying soil conditions to provide the most cost-effective or practical scope for a given jobsite. Once the scope has been determined and the engineering applied, the element can be installed and tested to determine if it is suitable. QA/QC programs are vital for the assurance that the element designed by the engineer has not only been properly constructed but that the design assumptions are confirmed. The two deep foundation elements referenced are drilled displacement piles (DDP) and micropiles. Each of these elements allows for large loads to be distributed deep into the subsurface geology. Having the technology and ability to monitor the tests in real-time can be beneficial to a contractor in determining if the design is adequate or if adjustments need to be made on future piles. The proper QA/QC guidelines for installation and monitoring need to be in place to ensure that an accurate interpretation can be made on the pile. This paper discusses the typical testing and the positive results that the author has encountered using the latest advances in strain analysis.KEY TERMSDrilled Displacement Piles:A deep foundation system that has the ability to shed load into the geology through shaft resistance as well as tip resistance, similar to drilled shafts. This pile element is unique in that it has a consistent pile section and thus a consistent modulus of elasticity.Micropile:A deep foundation system used in applications where the foundation lies over material not suitable for a spread footing and the ideal soil stratum is deep below the foundation. Micropiles will have two different cross-sections consisting of a cased section and an uncased section. For this reason, this pile type requires additional analysis when computing stress-strain relationships.Geokon Strain Gauges:Instrumentation such as Models 4911A-4911 Vibrating Wire Strain Gauges ( known as Sister Bars) are designed to be embedded in grout and calculate loads based on the change on grout strain over a period of time.Stress:A pile element is under a compression (axial loading) load when a force acts along its axis and is normal to the plane of the section. The corresponding stress the pile is experiencing is described as a normal stress. The stress is obtained by dividing the magnitude of the load distributed over the cross-section by the area of the pile cross-section, as shown in Eq. 1."

Jan 1, 2017

By Eric P. Bregman

As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800?s where busy commercial streets co-mingle with thickly settled residential houses. The subsurface conditions present within Boston?s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations. This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area.

By Eric P. Bregman, Franklin M. Grynkewicz, John E. Regan

"As part of an on-going effort to improve water quality and reduce discharge into Boston Harbor, the Massachusetts Water Resources Authority (MWRA) East Boston Branch Sewer Relief Project was designed under a Federal mandate from the United States Environmental Protection Agency (EPA) to upgrade the aging sewer system, increase system storage and greatly reduce the volume of combined sewer overflows into the Harbor. The project scope of work includes the installation of over 2 miles (11,800 linear feet) of 36-inch and 66-inch diameter sewer relief piping, twenty (20) temporary shafts and an approximate 100 foot open cut section, located within the densely populated neighborhood of East Boston, Massachusetts. This area is a former marshland backfilled in the early to mid 1800’s where busy commercial streets co-mingle with thickly settled residential houses.The subsurface conditions present within Boston’s complex geology include the presence of subsurface contamination as well as complex networks of underground utilities. Additional site limitations included low headroom, noise, and traffic restrictions. Together these limitations required the design of individual earth support systems, tailored for each shaft location. Moreover, challenging subsurface conditions identified during construction required design modifications to minimize cost and schedule impacts related to construction dewatering, treatment of contaminated groundwater, internal bracing, and utility relocations.This paper provides a case history of the Geo-structural design and performance of various earth support techniques utilized to construct jacking and receiving shafts designed to launch and receive two (2) micro-tunnel boring machines (MTBM) and to support the construction of new deep shaft structures in an urban coastal area."

Jan 1, 2017

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By James R. Gingery, Byron Foster, Bret Lingwall

While microzonation and setbacks are the typical mitigation for structures exposed to surface fault rupture hazards, lifelines and lifeline facilities are not easily relocated to avoid faulting. In these cases, other remedial measures including ground improvement may be warranted. Deep soil mixing ground improvement was used in this case to mitigate surface fault rupture and liquefaction hazards for a pump station at a wastewater treatment plant with wet wells up to 36-feet (11-m) deep. Paleoseismic field investigations were performed to characterize the site, then deterministic and probabilistic fault rupture displacement estimates were made and used to develop design scenarios. The fault rupture mitigation design consisted of a solid block of DSM encompassing and protecting the pump station and its wet wells. Three dimensional soil-structure interaction numerical modeling of the fault rupture scenarios was performed as part of the design. The analyses showed the fault rupture displacements could be diverted by the DSM and that satisfactory structure performance could be achieved. The design required construction of a large 100 percent replacement ratio block of DSM with a compressive strength of 500 psi. Aspects of construction of this DSM block are discussed.

Sep 8, 2021

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021

By Shigetoyo Yasui, Masahiro Saitou, Nobushige Yasuoka, Keisuke Tsujimoto

"The Dry Jet Mixing (DJM) Method was developed and has been put to practical use on the initiative of the Public Works Research Institute and Japan Construction Method and Machinery Research Institute. This method is used to inject powdery binder with compressed air into soft ground while mixing the binder with the soil using the mixing blade to reduce the moisture content of the ground and cause chemical reactions between the soil and binder, thereby strengthening the ground and stabilizing its quality.Recently, there is a demand for high-quality, high-accuracy execution control.This paper introduces the New DJM Execution Control System, developed to meet the future demand for more sophisticated ground improvement, based on the past results of the conventional system in order to provide new automated execution control with improved accuracy, functionality and column quantity.1. INTRODUCTIONIn association with the densification of cities and the improvement of the social overhead capital, the underground space in urban areas is tangled with various underground structures including transportation facilities such as subways and underground roads, buried pipe such as water supply and sewerage systems,gas, electric power and communications lines, and underground malls.In addition, a lot of aboveground structures such as office and residential buildings, elevated tracks, expressways, embankment tracks are also supported with underground foundations.Tokyo, Osaka, Nagoya and many other large cities in Japan grow on plains spread along the coast or rivers. Waterfront flat areas which are very convenient for human activities, however, are often on the alluvial soft ground, where soft cohesive soil with a high moisture content, loose sandy soil, etc. are accumulated in a thick formation, with a high groundwater level.The DJM Method introduced here is used to decrease the moisture content of the soft ground, strengthen the ground and stabilize the soil quality by injecting powdery binder into the ground with compressed air, while mixing the binder with the soil using the mixing blade.2. OUTLINE OF DJM METHODThe DJM Method is used to inject powdery binder with compressed air into soft ground, while mixing the binder with the soil using the mixing blade, to cause chemical reactions between the soil and binder, thereby decreasing the moisture content of the ground and strengthen and stabilize the ground."

Jan 1, 2015

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Andrew McNamara, Stuart Norman, Matthew Dearing, Michael Pelken, Asha Panchal

The deep foundations industry has largely remained unchanged since in the advent of CFA piling in the 1960s. Piles have consequently been designed and constructed following the traditional codes and standards without much regard for optimising in-life efficiency or end-of-life reuse. After existing developments have been demolished there is little motivation to reuse existing piled foundations as their load bearing capacity and structural integrity cannot be verified. Therefore piling contractors are increasingly spending more resources on coring through existing piles, only to be replaced with larger diameter or deeper piles. The hollow element of the HIPER® Pile provides access to the entire length of the pile to permit inspections and a shaft in which the pile can be extended if needed. This paper presents and compares the embodied carbon savings, both during construction and through foundation reuse, from a HIPER® Pile scheme compared with the traditional solid pile scheme. A discussion on the benefits of this technology and its implications on warranties and approvals is also presented to motivate the foundations industry to embrace whole lifecycle assessments and support the journey to net-zero carbon.

May 1, 2022

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By Ezra Ballinger, Matthew R. Glisson

Located in downtown Fargo, North Dakota, the Block 9 Redevelopment project site contains highly- compressible soils in the upper 100 feet with groundwater about 10 to 15 feet below the existing ground surface. The owner prohibited using driven piles to avoid disturbing neighbors of the project and historically, drilled shafts are used in Fargo as a reduced noise and vibration alternative to driven piles. However, developments over the last 20 to 30 years in drilling equipment, load testing and integrity testing resulted in the project team identifying augered cast-in-place piles as a suitable alternative for this project. To reduce the risks associated with using a relatively unproven foundation system in the area, the project team used the design-build delivery method for foundation design and construction. The team also specified compression load testing and higher-than-normal integrity testing. A successful bi-directional load test validated the design parameters for the augered cast-in-place pile while thermal integrity profiling gave the team confidence that these piles would perform similarly to the test pile. PROJECT DESCRIPTION The Block 9 Redevelopment project goal was to turn an existing, at-grade parking lot in downtown Fargo, North Dakota into a public outdoor plaza, a mixed-use building and a parking ramp. The project provides new offices, retail spaces, a hotel, a restaurant and private apartments. Situated in the southeast quadrant at the intersection of Broadway and 3rd Avenue North, the project site wraps around a bank building that was to remain. According to aerial photographs, the eastern portion of the site contained a public parking ramp that was constructed between 1952 and 1976, and subsequently demolished between 2009 and 2010. The western portion of the site had some combination of buildings and surface parking visible in aerial photographs taken between 1952 and 1979. Since 1984, aerial photographs show the western portion of the site being entirely surface parking. The redevelopment included the construction of three structures: the Tower, the Podium and the Parking Ramp, as shown in Fig. 1. With plan dimensions of roughly 100 feet by 100 feet, the Tower has 1 level of below-grade parking and 19 above-grade levels rising to a height of about 230 feet above grade. The Tower contains eight levels of commercial office space, four levels of hotel, six levels of residences and a mechanical level. This configuration resulted in column service loads ranging between 435 and 2,685 kips. The Tower core area has a total service load of about 30,000 kips.

Jan 1, 2019

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) method as the representative deep mixing technique has been demonstrating best practice on ground mitigation works coping with complicated soil condition and limited site space. This technique plays an important role in many projects to stabilize soft ground involving troubles like sliding failure, settlement, bearing capacity etc. Serious disasters caused larger earthquakes make great demand on the application of deep soil mixing these days. Special design and alignment of deep soil mixing has been established against to liquefaction and serious failure due to liquefaction. In this paper, representative example of liquefaction mitigation by DJM method is summarized. The paper also present result of surveillance of sites installed DJM col umns after attack by Tohoku Pacific Ocean Earthquake. Performance of DJM columns suffered the earthquake is demonstrated at several sites even with conventional column alignment.INTRODUCTIONThe DJM method is a representative deep soil mixing technique of dry mixing manner in Japan. DJM can successfully install soil mixing columns trough automatically controlled binder injection based on pneumatic feeding theory and cumulative experiences.This method was joint-developed in 1978 by private organization under initiative of the Public Works Research Institute of the Ministry of Construction as the optimum method for improving the Japanese soft ground. Figure 1 shows full view of the DJM construction system. Figure 2 illustrates DJM working system indicating Binder Feeding Plant side and Mixing Machine side respectively.As typical soil mitigation method, many projects related with rivers and roads and city development has required DJM technology. The total number of the projects applying DJM has exceeded 5,000 with the total treated soil volume more than 32,000,000 m3 by the end of fiscal year 2013."

Jan 1, 2015