Search Documents

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By Caitlin Rogers

The environmental and economic sustainability of froth flotation is dependent on effective management, which in turn improves the performance of a concentrator. In economic terms this means improved recovery of valuable minerals, in environmental terms this means effective management of acid generating tailings. Three indicators were selected to measure the performance of an integrated flotation system. The system consists of two stages of flotation; valuable mineral flotation followed by environmental desulfurisation by froth flotation. The suitable indicators were selected based on their fulfilment of four attributes. An attribute is a desired aspect of an indicator. The four attributes were: comprehensive, relevant, sensitive and quantitative. Two environmental indicators and one economic indicator were selected. They represent revenue generation from valuable minerals and environmental cost of management. The suitability of the selected indicators was shown using illustrative scenarios.

Jan 1, 2014

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014

By X. W. Lv

The intelligent recognizing and processing system for sinter ore mineragraphy make a great convenience of recognition and measurement. Specially, it?s critical important for a successful intelligent system to extract the minerals? feature accurately and sufficiently. Reflection index, as the crucial feature of mineral, is calculated by the theoretical calculating model of index based on the principle of imaging color models. In gray histogram of minerals? micrograph, the peaks? positions represent the information about mineral categories and contents. The relationships of different minerals? peak-positions in curve of gray histogram were got by using the peak-find model of gray histogram and calculating model of reflection index. These two models which can be regard as the method of feature extraction for minerals? photomicrograph also lay a good foundation for the artificial intelligent system of recognition and processing in sinter ore.

Jan 1, 2014

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. These ores require mineral processing to remove the sub-strate/nuclei rock before smelting. This paper reviews experimental results of previous investigations. Observations and analysis of 10 samples from different localities were carried out and it was found that the liberation ratio of crushed product was high even at coarse size fraction, 0.5mm to 4mm. Experimental and calculated results in the smelting stage confirmed that the separation product satisfies the standards of the subsequent smelting process if the substrate/nuclei rock is removed from the 0.5mm to 4mm fraction with high separation efficiency. There was a density difference between the substrate/nuclei rock and the ferromanganese component. Thus the coarse sized sample was treated with gravity separation; air table separation was used as a dry method and jig separation as a wet method and high grade values with high recoveries were obtained by both kinds of gravity separation.

Jan 1, 2014

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By N. Karapinar

Ferrihydrite, a member of iron oxides family, has been used as an adsorbent for the removal of heavy metal ions from industrial wastewater. The success of the operation depends mainly on the efficient removal of ferrihydrite from the aqueous phase. Hence, the emphasis of this study was given on the separation of ferrihydrite by high gradient magnetic separation (HGMS) method to overcome solid-liquid separation difficulties of ferrihydrite. Magnetic seeding technique in which the magnetite mineral was chosen as a seeding reagent was used to make magnetic separation available. The method clearly involves the attachment of ferrihydrite to a magnetic seed material and subsequent magnetic separation of ferrihydrite ? magnetite coagulates. Seeding of ferrihydrite with magnetic particles was achieved by exceeding the solubility limit of the ions in the presence of dispersed magnetite. Magnetic separation results of seeded ferrihydrite showed that maximum seeding performance is obtained in the pH range of 7.0~10.0. Iron/magnetite ratio had a marked effect on the separation of seeded iron oxide precipitate by HGMS. This ratio determines the operation parameters such as magnetic field strength and flow rate. It was concluded that when used with magnetic seeding technique, HGMS can be used to surpass separation difficulties of ferrihydrite used in adsorption-based treatment techniques.

Jan 1, 2014

By M. Nonaka

An attempt to produce fuel from biomass waste by hydrothermal treatment has been made with expectation to effectively utilize a renewable source of energy and an unexploited energy resource. In this paper, we have used empty fruit bunch (EFB) that is a residue after recovery of crude palm oil from palm oil trees in a plantation in a tropic country. A hydrothermal treatment was conducted using a 500 mL autoclave, with alkali (K2CO3) catalyst. EFB was decomposed more by alkali catalyst of lower alkali content and rather polymerized in higher catalytic region. The functional group composition of the solid phase oil is similar independent of alkali content, however its burning characteristic became more incombustible with increasing alkali content.

Jan 1, 2014

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By F. Concha

A robust theory of sedimentation-consolidation evolved and was accepted by researchers world-wide in the last two decades of the 20th century. This theory provides a reliable method of thickener design and simulation. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Research workers at the University of Concepción, together with Cettem Mineral Technology Center, created an integrated system of thickener design, simulation and control, including instrumentation, algorithm and software, which can be used by personnel in industry without specialized knowledge of thickening theory. In the paper, the development of three instruments for the measurement of pulp concentration, solid flux density and sediment compressibility is described. Each instrument uses software for data input, parameter calculation and results display. The paper also describes software for the optimization of the experimental parameter and for the design and simulation of industrial thickeners. Finally, mathematical algorithm and control strategies based on the phenomenological model are presented and compared with classical feedback control.

Jan 1, 2014

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By X. W. Zhang

Mica plate is broadly used in electric industry, production of man-made mica paper plate is in-creasing. The problem coming with is that large quantities of leftover materials unable to be re-cycled are produced during cutting and molding of mica plate productions. The leftover materials are always abandoned as crabs, which not only pollute the environment but also waste our resources. The study intends to find a new measure to decompose and to reuse the mica plate leftover materials so as to create a new production process of mica plate, which is clean and does not produce crabs.

Jan 1, 2014

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By Sergey Romanenko, Tatyana Aleksandrova, Karen Arustamian

"Current status of question about grinding stage effect to electrochemistry parameters of operation preparation slurry before intermediate selective flotation was assessed in the present scientific work. Needs of more detail study chemical reactions in the slurry preparation and flotation processes were shown. The ores are polymetallic sulphide type and the one are most difficult for mineral processing. The methodology allows increase information base during floatation tests. Ionometric methods and elements of neural network have been used in the study of mineral processing questions.We have also identified the relationship between the received values of the electrochemical parameters and the technological results in selective flotation. The optimal values of the electrochemistry parameters in operation of the preparation slurry before selective flotation has been found. The main effect of using the proposed methodology is to obtain scientifically based solutions to improve the technology parameters of flotation polymetallic sulfide ores. Challenging issue of selectivity of sulphide-polymetallic ores will be considered using case study of sulphidepolymetallic ores. It was shown that several factors are formed in ore grinding: formation of hydroxyl oxides of iron compounds, copper cation leaching, metal-sulphide and metal-sulphite complexes formation. The chemistry was revealed for current processes in slurry preparation operation before selective flotation. Quantitative assessment of interrelations between electrochemical parameters of slurry and process performance was given with using electrochemical control methods. Neuron network-based model was estimated based on data array and was allowed to establish optimum electrochemical conditions of metal-sulphite complex formation to provide maximum efficiency of selective flotation.INTRODUCTIONPhysical and chemical processes that take place in ore grinding have a significant impact on flotation selectivity and can cause low selectivity of the flotation process. Today this issue is given much attention. In the paper [1] it is pointed out that sulphide oxidation products and slurry components, such as sulphide ions, metallic iron and its oxidation products, have effect on flotation performance. So, metallic iron has impact on metal-sulphite complex formation as a result of oxidation-reduction reactions as follows:"

Jan 1, 2018

By B. Q. Xiao

The nitrate content is an important factor for environmental water samples and flour. In a 0.35 mol/L H2SO4-2NO solution, has a strong catalyzing function on the decolourization of Gallocya-nine (GC) oxidated by NaBrO3. Based on this, a novel method was developed to measure the NO and -3NO concentrations in water and flour. The flow injection technology was introduced into the analysis system. A single-valve dual- cingulums to inject which the Copperized-Cadmium slice and the reduction zone are isolated. The optimum solution for this method contains 1.48×10-4 mol/L GC, 0.06 mol /L NaBrO3 and 0.2 mol /L of NH4-2NOCl. Two empirical equations were proposed to calculate the and -3NO concentrations based on the measured signals. It can be used to measure -2NO of from 0.001 mg / L to 2.0 mg/L and -3NO of from 0.002 mg / L to 2.5 mg/L. The measurement frequency can be up to 20 samples / h. The relative standard deviation for eleven samples is less than 5%.

Jan 1, 2014

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014