Search Documents

By Chen Dong, Yang Wenwang, Liu Zhineng, Tan Ming

"To meet the requirement of production expanding of a certain potash ore dressing plant in Xinjiang province of China, industrial test of XCF/KYF-50 flotation machine was performed to process potash ore. The tank of XCF/KYF-50 flotation cell is in U shape, 50m3 of volume. This flotation cell is able to suck slurry by itself, and can be arranged on the same base level without high difference. In this paper, two sets of XCF/KYF-50 flotation cells were adopted to replace 8 sets of 8m3 flotation cell in original flow sheet of flotation. Aeration rate, slurry suction capacity, power consumption and slurry suspension are investigated. The measuring results show the slurry suction capacity of the flotation cell is larger than 12.80m3/min and solid particles disperse evenly in the tank without deposition. Industrial test result indicates that the final grade of concentrate is 26.69% at the recovery of 90.95%, which is up to expected performance. XCF/KYF-50 flotation cell has advantages of high flotation efficiency, significant energy saving and reasonable configuration of automatic control system, this kind of flotation cell can meet the requirement of production expanding of this potash ore dressing plant well."

Jan 1, 2014

Systemic process mineralogy study on Baerbulawu refractory hematite ore in Kazakhstan has been carried out. The ore contains Fe 41.34%, and 87.26 % of which exists in hematite. Most hema-tite occurs as fine or ultrafine grains and its average size is only 0.015mm. The gangue is mainly composed of quartz, mica, chlorite, kaolinite and other clay minerals. The liberation of hematite is only 66% when the ore is grinded to 75% ?0.074mm, while part of gangue is already liberated from hematite under this grinding condition, so these gangue can be cast away by magnetic separation in advance. Hematite will not liberate completely from gangue untill grinding fineness reaches 86% ?0.038mm, at the same time, free particles of ultrafine hematite tend to coagulate randomly with quartz and clay minerals, so appropriate dispersant is necessary to pre-vent hematite and clay minerals from coagulation. Based on the process mineralogy research, final technology flowsheet is high-intensity magnetic separation by coarse grinding?rough magnetic concentrate regrinding?inverse flotation, and an ideal index is achieved. The yield of final iron concentrate is 43.46%, and its grade and recovery are 66.76% and 70.55% respectively. The research result is also useful to other similar iron ores.

Jan 1, 2014

By Polezhaev S. Yu, I. V. Ukraintsev, Boduen A. Ya, Saburbayeva L. Yu

"Comparison studies of different technologies are performed when selecting optimum option for gold ore and concentrate processing. Methods of ultrafine grinding, oxidizing roasting, bacterial leaching and pressure oxidation are used to extract gold from refractory ores and concentrates. Refractory gold flotation concentrate produced from pyrite-arsenopyrite ores of Bestobe deposit is a case study in this paper. The results of the experimental tests of the direct leaching of flotation concentrate and pre-oxidation products using different methods (oxidizing roasting cinder, pressure oxidation and bacterial leaching cakes) are the following: - cyanidation of original flotation concentrate provides recovery of Au at 46.6 %; - oxidizing roasting increases gold recovery from 46.6 % to 85 %; - BIOX increases gold recovery up to 86 %; - preliminary pressure oxidation of flotation concentrate ensures steadily high Au extraction in the follow-up cyanidation at 94.9-96.5 %. Pressure oxidation and bio-oxidation has changed dramatically the strategy of refractory gold ore processing. These solutions provided for development of ore deposits that considered earlier non-commercial. However, refractory ore processing has a complex character in terms of developing process flowsheet and requires large amount of studies to be performed for each new project. Gold extraction is the basic but not the only criteria to technology selection for gold ore and concentrate processing. Opex and capex, ore reserves, regional geography, developed infrastructure and skill personnel should be considered. Process studies and feasibility study of the developed technology shall be provided for each specific gold ore deposit. INTRODUCTION Due to changes in available feedstock and depletion of easy-to-process ores, refractory ores containing finely disseminated gold and silver in sulphides (primarily, in pyrites and arsenopyrites) are more and more involved into processing. Experts say that such ores amount above 40 % of the world’s gold reserves. Conventional technologies of gold extraction from refractory ores include flotation, roasting and cinder cyanidation (Fraser etal., 1991). However, today’s best available practice for refractory gold ore processing are bacterial (BIOX) and pressure (POX) oxidation."

Jan 1, 2018

By K. Kiangi

On installing the Metso Superior MK 54x75? primary gyratory crusher in Nkomati mine the crusher experienced severe power spikes greater than 1000kW which subsequently led to the crusher tripping under load while processing some of Nkomati?s MMZ ores. Likewise significant losses in throughput were also experienced while processing some of Nkomati?s MMZ ore types. Interestingly the crusher was capable of processing the PCMZ ores without experiencing any power spikes or losses in throughput. Investigations into the challenges faced by the crusher while processing Nkomati?s MMZ ores were conducted using the DEM model in conjunction with the fast breakage model present in Metso?s High Fidelity Simulator. The intentions of the study were to establish the most suitable operating conditions or cavity design that would potentially enhance the performance of the crusher. Likewise an understanding of the effects the feed conditions (size distribution and hardness) had on the crusher?s performance was established. Ore characterization tests were conducted on Nkomati?sPyroxenite, Diabase, Calc silicate and quartzite ores which were from Nkomati?s MMZ ore body. The ore characterization tests conducted were drop weight tests, slow compression tests and elastic modulus tests. Four simulations were conducted used the existing cavity design with various open side settings (OSS) and throws. This established the effects of changing the crusher?s operating conditions on its performance. Four additional simulations were conducted on two cavity designs with reduced volumes. This established the effects of changing the crusher?s cavity design on the crusher?s performance. Thus through the simulations a better understandings of the impact of the crusher design, operating conditions and feed conditions on the crushers performance. Furthermore an analysis of the crusher?s performance was made which was used as a basis for comparisons with the base case simulation. Keywords: crusher, discrete element method, simulation, ore characterization

Sep 1, 2012

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

By Roberto Galéry, Braz J. C. Filho, Marcelo M. Stopa, Douglas B. Mazzinghy, Priscila M. Esteves

"The purpose of the research is to monitor ball mill filling by means of signals usually measured in its electrical drive. The method is based on the mill torque estimated from rotor speed and induction motor stator voltage and currents. New signal processing is presented in both time and frequency domain for measurements in a dry laboratory ball mill. Statistical analysis is applied to time series resulting in good correlation to mill filling. Fast Fourier Transform (FFT) and power spectral density (PSD) also resulted in an accurate filling indicator. The proposed method does not need any sensor to be installed directly on the mill and requires only sensors usually available for motor control purposes. The experimental results showed that the method have potential to be used to construct an automatic system for monitoring operational variables in ball mills. The aim of this monitoring is to improve energy efficiency, reliability and productivity.INTRODUCTION Recently, a great number of papers have pointed the importance of ball mill filling monitoring and also of grinding control (Lu, et al., 2014) (Ramasamy, et al., 2005) (Tsamatsoulis, 2014) (Zhou, et al., 2009). Additionally, great amount of control techniques have also been presented with several complexity degrees (Tsamatsoulis, 2014). According to Eremenko (2015) the lack of effective and accurate methods for fill level measurement is the main reason that makes mill optimal control so complicated. It happens because nonlinearity, long time delay and time varying features of the ball mill turns difficult to develop a truly efficient method for monitoring filling. At the same time, fill level has a determining role in charge motion and consequently on particle breakage. For low levels of filling many energy is expended in impacts with very low breakage efficiency. Those impacts can also damage mill liner. In contrast, high levels of filling causes damping effects that reduces breakage and can also affect energy consumption. Based on this it is conclusive that fill level measurement of ball mills is an important issue for grinding efficiency. This fill level information can be used for operators to control ball mills and also for engineers to run simulations and improve confidence levels of circuit designs (Shi, 2016)."

Jan 1, 2018

By Thomas Mütze, Michael Klichowicz, Mathis Reichert, Holger Lieberwirth

"Self-similarity is proofed to be a common feature when brittle material is comminuted, either in particle bed or single particle mode. Appropriate test work is well documented for particle sizes less than 7 mm in several publications. In contrast, almost no research has been done for coarser particles. The aim of this paper is to show that the fracture pattern of coarser material also tends to be self-similar. Hence, single particles of quartzite, granodiorite and dolomite were comminuted under compressive load. The focus was set on three different size fractions -3.15 +2.5 mm, -31.5 +25 mm and lumps -300 mm. According to the wide range of particle sizes, three different piston-die presses were used with a maximum compressive force ranging from 5 kN to 4000 kN. The force-displacement curves were recorded in order to calculate the specific comminution energy. Additionally, the -31.5 +25 mm size fraction was crushed in a laboratory scale jaw crusher and a roll crusher. Some authors report that the energy-size-reduction relationship of self-similar materials can be approximated by a linear function, which is independent of the comminution equipment. In their charts the slope can be seen as a product-size-independent grindability measure. Our tests show a self-similar breakage behavior when particles in a range of -300 +3 mm are comminuted in single particle mode. Furthermore, the products of the piston-die-presses and the roll crusher are similar to each other in a self-similar representation of the particle size distribution. The jaw crusher product, however, is not self-similar compared to the piston-die-press products. Finally, the linear energy-size-reduction relationships are confirmed for each fraction, but show size dependent slopes."

Jan 1, 2014

By V. Dementiev

Pyrite cinders is a complex raw material, in which the valuable metals are: Au(2.04 g/t), Ag(35.0 g/t), Cu(0.38%), Zn(1.1%) and Fe(56.0%). In this case high costs for mining and ore processing are not required. The hydrometallurgical treatment of pyrite cinders using thiourea, sulfite and cyanide solutions are examined in this paper. It was found that thiourea leaching is ineffective due to high consumption of thiourea and sulfuric acid. The cyanidation on pyrite cinders was conducted. Various options of the preparation of the products for the subsequent cyanidation have been examined. The tests on cyanidation process optimization were conducted. The effectiveness of these cementation methods by metallic iron or extraction for copper recovery from water phase has been shown. Zinc precipitation can be found in the form of carbonate. In order to recover noble metals from cyanide solutions, the cementation onto zinc dust was tested. The developed technology provides for recovery at 49-56%Au, 20-25%Ag, 22.5%Cu and 50%Zn during NaCN (1.4 kg/t) and CaO (6 kg/t) consumption. The results of pilot plant testing are the basis for technical regulations in order to design a pyrite cinders treatment plant. The technology has been examined in pilot-plant conditions. In this case the recovery of 54.5%Au, 45.3%Ag, 30%Cu and 49.9%Zn was achieved to provide saleable products. Keywords: pyrite cinders, thiourea leaching

Sep 1, 2012

By N. A. Dementyeva

To improve gold recovery from preg-robbing carbonaceous ores a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon-in-leach (CIL) process for intensive cyanidation tailings and the recleaned concentrate was developed. The final flotation tailings are shipped to tailings disposal. Total gold recovery by the proposed technology from the ore with the head grade of 0.8 g/t was 83.9%. The gold loading onto the activated carbon from CIL process was 6.5 g/kg.

Jan 1, 2014

By Arkady Senchenko, Andrey Vasiliev, Alexander Aksenov, Metodi Zlatev

"This paper considers the issue of treating argillaceous oxidized ores with low gold grade (around 1.0 g/t). These ores according to their gold recovery level can be treated by heap leaching and agitation cyanide leaching, but low gold grade makes this treatment uneconomic. Heap leaching of argillaceous ores requires high consumption of binding agent for pelletizing to create suitable hydro-physical properties of material, which leads to increasing process cost and makes the material treatment unprofitable. Agitation cyanide leaching of this ore requires grinding processes; these expenses would not be paid back by the amount of gold recovered. Considering the above, poor argillaceous oxidized ores are recommended to be treated according to a combined technology including fractionation of ore, heap leaching of coarse fraction and agitation leaching of argillaceous fraction. Complex approach application allows one to avoid expenses incurred for material grinding and high consumption of binding agent for pelletizing. The success of this technology implementation will firstly depend on the quality of material fractionation, therefore the section of disintegration and division of ore into different components will be the most important part of flowsheet development for gold production. When disintegrating minerals at positive temperatures both standard (mechanical disintegration - scrubbers) and innovative (hydraulic method of disintegration - HydroClean units) equipment is applicable. HydroClean units are characterized by lower energy and water consumption. In a number of cases it is required to treat frozen ores. When treating frozen material standard approaches to disintegration are not reasonable due to their low efficiency. In order to treat frozen material a two stage disintegration flowsheet with screening after each stage is recommended. The first stage is recommended to be performed in a scrubber, the second - in a HydroClean unit. This technological flowsheet will provide high and steady values for ore separation into fractions at low energy consumption for disintegration."

Jan 1, 2014

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By U. M. J. Boin, W. L. Dalmijn, T. P. R. de Jong

"This paper explores the complex interrelationship between the resource cycle, recycling and metal production as a function of economics, environmental legislation, and product design. It is argued that central to optimising this resource cycle lies the control in particular of physical separation plants by the application of advanced sensor technology and sorting equipment, as well as suitable control and sampling algorithms supported by optimising mass balance models.Metals are produced through a long chain of processes. For primary resources, metals production goes through mining, mineral processing, ore smelting, conversion and refining steps or via low temperature hydrometallurgical processes, or a combination of both pyro- and hydrometallurgical operations. For the recycling of resources, metals are separated and recovered from metal scrap, which plays an increasingly important role in the world. Metals after being produced, either from primary or recycling resources, have to be further refined or manufactured into various types of alloys and finally shaped into different products for the end-users. Since the end-user discards products the contained materials find their way back into the resource cycle as scrap. Therefore, controlling the metallurgical reactors also controls, in a much broader sense, the material quality in the complete metals cycle, from the production phase, to the end-use phase, up to the recycling phase (Reuter et al., 2003). The recycling phase includes separation of materials into saleable intermediate products, which are reintroduced into the production phase as a recycling resource. Therefore, the metallurgical processes in each unit operation in the metals production and processing chain have to be controlled, so as to achieve optimal performance of high product quality, low energy and materials consumption, and low environmental impact."

Jan 1, 2003

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini

Vertical ring and Pulsating Wet High Intensity Magnetic Separator (VP-WHIMS) is widely used for week magnetic mineral beneficiation or ferrous impurity removal from non-metallic minerals. Because of the complexity of this machine, mathematical modelling of its process is complicated and time consuming. In this paper, artificial neural network (ANN) and response surface methodology (RSM) were applied to evaluate the VP-WHIMS performance and optimize its main operating parameters in beneficiating of the Chadormalu hematite sample. The operational parameters of this magnetic separator are considered as: magnetic field intensity (2500-8500 gauss), pulsating frequency (20-100 %max), ring rotation speed (0.6-4.6 r/min) and slurry concentration (15-35 w/w %). Concentrate grade and recoveries (weight and Fe) are monitored as responses. Centre composite design (CCD) was used for experimental study. Four process variables were set using small CCD. Eight star points (a=±1), eight axial points (a=±2) and five replicates at the centre point (a=0) were chosen as experimental points. In ANN system, the best network topology was obtained as (4-5-3). The weights connection and biases were obtained using batch back propagation (BBP) method for 21 experimental data points. The results indicate that ANN

Jan 1, 2014

By Georg Unland, Thomas Wegner

"Different types of impact crushers use the physical effect of impact to crush rocks. The rocks can vary from soft to hard and from ductile to brittle but they should never be abrasive. Since the principles of impact crushing of larger rocks are hardly investigated these crushers are still sized rather by empirical than by scientific approaches.In order to investigate the principles of comminution by impact of large rocks a test rotor was developed and rocks of different dimensions were tested. The integrated measuring devices of the rotor enable the recording of impact forces and of absorbed impact energy with high resolution during the contact time.Since impact crushers stress the rock particles with a defined velocity the main crushing properties are gained as a function of the applied velocity and the particle size of the rock: likelihood of breakage, contact time, maximum crushing force, mass specific crushing work, surface related crushing ratio and crushed fragment shape distribution."

Jan 1, 2003