Search Documents

By R W. Givens

This paper presents blast casting design variables that have been developed and are currently being used at the High Power Energy mine in West Virginia. The shot specifications are summarized in Table I. The two active casting pits were designed with casting in mind and as a result are better designed and more efficient. About 55% of the overburden material is effectively cast and clean up is done by a bulldozer, front-end-loader, and trucks. This results in a 15X decrease in the cost of coal production.

Jan 1, 1988

By Minoru Kawamora, Koichi Kurokawa, Kenji Hashimoto

We developed concentrated remote control blasting system to blasting simultaneously at a large number of sites in a mine of large scale. This system is consisted of three parts, the first part is a control station with high voltage power source units, the second part is a relay terminal with relaying and branching units, and the third part is a blasting machine with charging and discharging units. The control station is connected with the blasting machine by mean of control bus wire. The blasting machine adopts MBS(electromagnetic induction blasting system) for the reason of safety and good handling.

Jan 1, 1990

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By N L. Thomas

Hole size affects many factors which directly influence fragmentation in the muckpile and hence, the cost effectiveness of the entire operation. These factors include production capability, explosives and accessories efficiency and usage and drilling accuracy. In addition, hole size should be chosen to suit the geological conditions. The paper concludes that the optimum hole size is generally the largest that can be used commensurate with production and environmental considerations.

Jan 1, 1986

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Karl E. Burger

Recently an experiment was completed at the Golden Sunlight Mine, a property owned by Placer Dome Inc. of Vancouver, British Columbia, to measure the Body Waves entering their highwall created by blasting. The purpose of the study was to assess the damaging effects of blasting on the highwall, in order to further slope stability. Stress and Strain experienced in the earth that is created as a result of blasting can be determined by knowing several important pieces of information. These include the compressional and shear wave particle velocities initiated by blasting, the Body Wave travel velocities in both the shear and longitudinal direction, and the densities of the rock in question. A series of equations based on wave theory can then be used to determine the stress and strain affecting the highwalls. The Blasting Engineer can then use this information to design blasts that create peak particle velocities less than levels that maintain the integrity of the highwalls. This paper first discusses the experiment used to measure the Body Wave velocities. It then traces through the subsequent calculations necessary to generate the information needed by the Blasting Engineers, the Mining Engineers, the Geological Engineers, and the Geophysicists to design blasts and develop open pit plans to alleviate unstable highwall conditions.

Jan 1, 1989

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By T Davids, O J. Jordaan, M D. J Bonneau

As in most other parts of the world, the surface coal mining industry in South Africa is introducing emulsion explosives as the primary bulk blasting agent for use in wet borehole conditions where AN/FO cannot be used. Most of the emulsion products presently in use are gassed to provide sensitivity. The intimate mix between the fuel and oxidizer in the emulsion has been shown to produce a highly efficient explosive. However, a major difference between emulsion and the previous slurry products is its relatively low physical strength. This prompted Rand Mines' Duvha Opencast Mine, a major South African Escom power colliery, to conduct test work to illustrate the effect of emulsion physical consistency on blasthole loading. This paper presents the results of test work conducted at Duvha to investigate the problems associated with loading both AN/FO and emulsion in water filled holes, stemming emulsion holes, and in particular, to illustrate the difficulty in correctly introducing a stemming deck into the emulsion column. Time dependent behavior of the loaded emulsion holes is investigated. Velocity of detonation measurements for freshly manufactured emulsion, and for emulsion after loading through water with sleep times of up to 10 days, are presented.

Jan 1, 1987

By Joseph Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project. Information and transparency with the stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the chances of having a blasting project approved. This open communication starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. The blasting industry and regulators must work collaboratively to improve safety, security, regulations and licensing. Implementing state of the art blasting techniques, security, safety measures, vibration monitoring and strict licensing allows the AHJ and all stakeholders to remain integrated and informed, contributing to process approval. Regulatory operators should strive to achieve success thru communication, cooperation and compliance which is accomplished thru continued education and transparency. These steps, combined with regular meetings, has proven to be a benefit to both industry and regulators. Relationships are built through trust, teamwork, transparency and communication –including the take holders and AHJ in the approval process from the inception solidifies these relationships and improves teamwork

By Dale Preece, Vanessa Berg

This paper presents a two-pronged vulnerability analysis approach for treating minimally reinforced concrete (RC) structures subjected to explosive events. This work was motivated by a heightened interest in homeland protection involving both malevolent and accidental explosions and the need for assessment of critical facilities subjected to an explosive detonation. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN, while the second part of the analysis employs Single-Degree-of-Freedom (SDOF) methods, each predicting the dynamic response of the minimally RC walls, slabs and columns to explosive loading. The concrete is treated with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model, which accounts for failure mechanisms in brittle materials. Predictions from AUTODYN are verified using the equivalent SDOF reinforced concrete code, SPAn32, developed by the US Army Corp of Engineers and agreement between the results indicates a high level of accuracy in both methods of analysis, allowing for accurate predications of airblast-structure interactions and failure mechanisms.

Jan 1, 2004

By Sarah Guzzelli, Enrigue Munaretti, Anneliese Botelho, Jair Koppe

Drill and Blast (D & B) is one of the main operations in the mining production cycle, which aims to fragment rock according to a pre-defined plan for proper loading, haulage and processing specifications. In this sense, data from a Brazilian iron ore mine was analyzed, given emphasis on blasthole length, subdrilling and stemming. The D & B report, including mining data such as number of blastholes, length, and diameter and stemming aspects, was analyzed in order to be able to compare these results with the blast design. The study showed significant differences between the designed blasting pattern and that one obtained by the operation. As a consequence, problems such as inadequate fragmentation, incorrect size distribution and loss of energy, were identified. For example, when stemming has a different length than it should have, noise and flyrock can occur, including inadequate fragmentation and vibration in both situations. Therefore, a comparison between the usual D & B procedures and recommended D & B design based on literature reveals the most important deviations and their consequences. The study intends to identify solutions for simple problems, improving D & B operations and safety practices.

Jan 1, 2014

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

By D VanDoorselaere

"Image analysis techniques are widely used for blast fragmentation measurement, and various commercial packages are available for this purpose. These packages are very versatile and serve as a useful tool for optimization of blasting practice. But many times, the results provided by image analysis techniques do not match with sieved and predicted data. This leads to the suggestion that understanding the limitations of this technology is as important as understanding its usefulness and versatility.A study was conducted in two stages:(a) Comparison between the results of image analysis and screened data using laboratory scale muck piles.(b) Comparison between predicted (Kuz-Ram) and measured (Image analysis) blast fragmentation results for several bench blasts.During laboratory work, muck piles with known size distributions were analyzed with the help of image analysis technique. A disparity was observed between the sieved and measured results because the image analysis techniques cannot accurately determine the % of fi nes in the muck. During fi eld work about fourteen blasts were monitored. It was observed that predicted (Kuz-Ram) results rarely matched with measured (Image analysis) results. The Kuz-Ram curves were modifi ed by changing the rock factor so that the Kuz-Ram and Image analysis curves match in the vicinity of the 50% passing size. The pairs of curves (modifi ed Kuz-Ram and Image analysis) were divided into three categories depending upon their differences in the coarse and fi nes ranges. The blast design parameters affecting the difference between the pair of curves have been outlined. The suggestions have been made to better utilize the image analysis system."

Jan 1, 2007

By Dave Harrison, Phyllis Hasser, Ken Eltschlager

The beginning There was the video:– “Understanding Vibrations from Blasting” – 2002 to 2004 in development – Dale Ramsey ad hoc Public Education committee chair – Available At the ISEE bookstore Public Education and Public Relations Committee • Standing ISEE committee 2004 • Co-Chairs – Ken Eltschlager, Dave Harrison • Purpose: "Develop and conduct programs on public education and public relations. Public education programs will focus on public awareness, understanding, and appreciation of the explosives industry. Public relations programs will concentrate on providing blasting professionals with the tools to assist in the public's understanding of the explosive industry and in the appropriate ways to respond to local community issues."

Jan 1, 2007

By J. Meissner

In this paper vibratory crack response is compared to that produced by volumetric changes in foundation soils induced by natural events. These natural phenomena include changes in the water table, changes in soil moisture, and formation of ice lenses to name a few. Previous papers have compared vibratory responses of cracks to atmospheric effects such as those produced by the passage of weather fronts and daily changes in temperature and humidity. Periodicity of these atmospheric effects is on the order of a day to half a dozen days. Thus it is possible to observe atmospheric effects with measurement over a period of weeks to several months. On the other hand, crack response produced by volumetric changes in foundation soils occurs over a period of many months and/or may be seasonal in nature if not longer in the case of drought. Thus its measurement requires long periods of observation (many months to significant fractions of a year) or observation during critical seasons. Since it occurs over long periods of time, its observation may be obscured by climatologically induced crack response. These soil volume changes are compared with climatic data to describe the correlative nature of crack response in time with the soil volume change phenomena and likely climatic causes.

Jan 1, 2009

By Pierre Auger, Benoit Levesque, Richard Martel, Guy Sanfacon, Louis-Charles Boutin, Marc-Andre Lavigne, Patrick Brousseau, Luc Trepanier, Louise Galarneau

Explosives used for blasting operations in civil engineering works, like construction of piping systems under roads, of pools, of houses and buildings can generate large volumes of carbon monoxide (CO). Carbon monoxide can represent between 1 to 3% of the gases produced by usual explosives. The production of 10 to 24 1 of CO by kg of explosives blasted is theoretically anticipated. CO is a gas that has no characteristic colour, smell or taste. It can migrate in the fractured rock of the blasted areas on fair distances, and then infiltrate in closed spaces like sewage systems, manholes, but also in basements of houses. In Quebec, in the last 10 years, 7 people were poisoned by CO in their houses to the point that they had to be treated in hyperbaric chambers. In the USA, many accidents have occurred and one worker died in a manhole. From the review of intoxication cases, the distance of migration of CO may reach 55 m if a conduit is present underground. Underground conduits broken by blast, tilling around underground conduits in road or house trenches, or fractured rock created by blasts between houses or between a house and a road, are the different pathways identified in the Quebec incidents. Field tests were performed at sites close to CO intoxication locations in order to evaluate the behaviour of CO in fractured rock following blasting operations. From these tests, the following conclusions may be drawn. The structural geology of the rock formation (schistosity, family of joints, fractures) plays a role in the direction and extent of gas migration in fractures generated when rock is blasted with explosives. The confinement of the rock can affect the quantity of gas migrating in the fractured rock. Significant concentrations of CO may persist in the fractured rock even 7 days after a blast. Advection is the initial mechanism of CO migration in fractured rock generated by the blasts or naturally occurring before the blast. The distance of migration with this mechanism is short (5 to 8 m). In trenches of muck (equivalent to tills under roads) the distance of CO migration by advection is 12 to 20 m. In the 2 to 3 days following the blasts, further CO migration up to 15 m is made by diffusion in the induced fractures, or up to 30 m in the trenches. To minimise CO production and migration in the fractured rock during blasting, special procedures can be applied by the blasting contractors: (1) do the complete excavation of the overburden before drilling and put mats for each blast; (2) do the complete excavation of the muck after each blast; (3) the last blasting should be the one for the private services entrance of the house and the excavation of the muck should begin at the junction between the road trench and the services entrance trench. Another technique consists in the pumping of interstitial air in the muck with a vacuum truck immediately after each blast.

Jan 1, 2002

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Pavel A. Torres, Darwin Torres, Sandro Huaman

Given the limited efficiency of blast-induced ground vibrations prediction empirical models, due to the complex geological system from a Peruvian mine. An artificial neural network was built in order to get better results. More accurate and precise predictions allowed the generation of blasting domains for future designs and decision making.

Feb 1, 2020

By Dr. Zach Agioutantis, Elliott Morgan

The explosives, mining, and heavy civil industries consistently battle the uncertainty that is associated with working with a heterogenous medium like rock in blasting. This has led to studies to increase fundamental understanding of material response under dynamic loading that is associated with blasting. This study looks at the dynamic strain associated with blasting the lab Split-Hopkinson Pressure Bar (SHPB) testing while also building off of previous studies with the goal of better understanding the dynamic forces that are enacted on a geologic body during a blast loading event. This is required in order to advance geologic blast response modeling. This is achieved through analyzing the stress and strain values for each specimen that are calculated from strain data collected with a SHPB. Based on this data, the dynamic material response characteristics are able to be determined. Tests were conducted on five Berea Sandstone specimens with a rough length to diameter ratio (L/D) of 1.0. The strain data from these tests were then used to create stress strain curves as well as charts depicting failure stress to both strain rate and failure particle velocities. The tests conducted returned similar results to previous tests results on Berea Sandstone while also showing a correlation between strain rate at failure and failure particle velocities. While further research is needed, there is evidence that SHPB test data could be used in conjunction with the MBF model. The MBF model states that the peak particle velocity (PPV) of blast vibrations can be correlated with deformation (strain) at a given point. With a further understanding of dynamic material response correlated to PPV measurements, further refinement could allow for better prediction of blast performance.

Jan 21, 2025