Search Documents

By G Mendoza, L Taddei, C Robertson

It is a well-known industry fact that many mine sites around the globe experience blast holes that have elevated temperatures due to reactive ground, geochemical reactions, geomorphic reactions, sub level open fires, etc. It has been reported in many previous industry publications (White, Saputra et al) that elevated blast hole temperatures are a norm at many mine sites and are dealt with on an ongoing basis while the drill and blast process continues under elevated states of alert. The choice of explosives products including the type of detonator, primer, accessory, and bulk product all must be taken into consideration when loading blast holes where there is a known potential for elevated temperature conditions. It should also be noted that these elevated temperatures inside blast holes can be consistent throughout the blast hole length or vary in position within the blast hole depending on the mine conditions mentioned in the opening statement above. The risks associated with the loading of primers and bulk explosives in holes where elevated temperatures are present include: the ejection of the bulk explosives product, deflagration of the explosives during initiation of the blast or premature and uncontrolled initiation of a blast hole(s). This paper describes a unique and novel approach to the active monitoring of the temperature within blast holes with the application of electronic detonators with integrated temperature measuring (ITM) capabilities, deployed and demonstrated at a mine site in Mexico during January 2023 to March 2023. The deployment of ITM capable electronic detonators allows a user to monitor and record the real time temperature at multiple locations (e.g., toe, middle and collar) at each electronic detonator’s position within the blast hole, with the ability to react instantaneously to elevations in temperature reported. The measurement of the temperature can be for a single ITM electronic detonator, or simultaneous for an array of ITM electronic detonators, allowing for the potential for the data to be represented by a time/temperature/hole depth three-dimensional heat map. Changes in temperature at different borehole positions can vary, however, often the collar position is expected to be the most reactive due the combination of bulk explosive product and oxygen exposure, which can be confirmed with the application of the ITM electronic detonators. A mine site’s reaction to a measured elevated temperature within a blast hole can vary depending on the temperature measured and the change in temperature from the last measurement made. The study was found to produce real-time in-hole temperature information which was previously unobtainable without the introduction of another device. New and adaptive elevated temperature hole policies can be created and adapted proactively as real time information is received, leading to a safer mining operation.

Jan 21, 2025

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By Dennis Wilzbacher, John Wiegand

In an effort to reduce the cost of bulk explosives, Vigo Coal Company found that the addition of coal mined at their Friendsville Mine, not only reduced explosive costs, but also appeared to actually enhance blasting performance. The Friendsville Coal lies at the base of the Mattoon geologic formation within the Mcleansboro Group of the Missourian Series of the Pennsylvanian Geologic System in Southern Illinois. Vigo Coal Company commissioned VIBRONICS, INC., an independent blasting consulting company to quantify actual blasting performance. Insitu sonic velocity testing of overburden was conducted to determine the P-wave velocity of the sandstone present at Vigo’s Cypress Creek Mine, where the initial testing was conducted. Numerous VOD (velocity of detonation) recordings were obtained for varying blends of ANFO/Coal (now named Carbo*Prill). Cast blast percentages were determined for both Carbo*Prill and non coal blended bulk explosive blasts. The VOD of the coal blended product was intentionally reduced so as to more closely match the P-wave velocity of the sandstone overburden. Explosive blends containing as much as 40-50 percent coal were tested. Explosive blends containing greater than 30 percent coal, have been used in Cypress Creek Mine overburden production blasts. The coal blends appear to produce better fragmentation and yield excellent cast blast performance. Safer mining conditions were also observed. Flyrock potential was reduced. The blasts produced less back break, producing a safer highwall. Stripping dozer and shovel production rose during the testing period and equipment repair costs were lowered due to an increase in overburden fragmentation. Blasting vibrations were reduced, in part due to the lowered detonation velocity of the ANFO/Coal mixture. The Friendsville Coal Seam appears to contain inherent chemical and physical properties that enhance blasting performance. The use of Carbo*Prill has been approved by MSHA, BATF, the State of Illinois, and the State of Indiana. This paper will provide details concerning testing procedures, blast performance analysis, recommendations and conclusions for using this alternative blasting mixture.

Jan 1, 2007

By Lawrence C. K Hu

The release of load mechanism during rock breakage by explosives was founded by Dr. T. N. Hagan & published at the Sixth International Colloquium on Gasdynamics of Explosions and Reactive Systems Stockholm, Sweden, 1977.

Jan 1, 1995

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Rolf Schillinger

Transport of Small Quantities of Explosives Material on Public Roads The transport of dangerous goods on public roads is extensively regulated by EU and national law. The transport of explosive material is not only done by forwarders but also by small companies and private persons with the goal of their own use. The following article tries to explain what is allowed and what is not.

Jan 1, 2010

By Scott G. Giltner, Alex Schwenk

Blasting within 250 ft of a crusher was successfully executed through the application of electronic detonators, 3-D imagery, signature hole analysis, custom loading of blast holes. The blast was well contained, the vibrations were minimal, and there was no flyrock.

Feb 1, 2020

By S. Mansfield, A. Sharma

At a large open cut copper mine, in pit crushing and conveying is used to shorten haul routes and minimise stockpiling of ore. This strategy decreases capital expenditure by reducing the number of haul trucks and excavators required and reduces the need to rehandle ore from stockpiles with a secondary load and haul fleet, with an overall goal of lowering operating costs and carbon emissions. As the mine has developed and expanded, it was necessary to extend the conveying network and install a fourth, semi-mobile crusher to increase the output of the operation, while maintaining the operational efficiencies. This required the blasting of a new tipping bench and pocket for the installation of one of the largest and most powerful semi-mobile, crushing plants. Fed by 360 tonne (396 ton) ultra-heavy class haul trucks, the KB 63-130 Pro gyratory crusher is the highest capacity available in the market. This paper describes the holistic process that was applied to model, design and execute the blasts required to create the pocket for the semi-mobile crusher, the surrounding tipping bench, plus the conveyor corridor and access ramp used by the ultra-heavy class trucks.

Jan 1, 2024

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By J. P. Remi Proulx, Areli Rodriguez, Ruilin Yang

Historically, presplitting has been considered effective in reducing the impact of blast vibrations on highwalls. However, it remains a debated topic: how significantly can it protect highwalls, and is it worth the cost and effort to implement presplit blasting techniques? In hard rock, presplit blasting can leave half-barrels on the highwalls, clearly demonstrating its usefulness. However, in a fractured rock mass, the half-barrels from presplit blasting may not appear in most cases, leading to questions about its role in protecting highwalls. Previous studies in the literature used geophones to measure blast vibrations at far distances and could not ascertain the significant benefit of presplit blasting in reducing the impact of blast vibrations on highwalls. Additionally, no studies in the literature address the role of presplitting in alleviating blasting-released gas pressure that could penetrate joints and open new fractures in highwalls. Yang & Proulx (2019) and Yang et al. (2022) using near-field blast vibration monitoring of signature hole blasts have revealed that the peak particle velocity (PPV) of blast vibrations at a scaled distance of 1 m/kg^0.5 can be reduced by 50% or more for presplit-filtered vibrations. These results have been confirmed for both hard rock and fractured ground. In addition to summarizing the reduction in blast vibrations due to presplitting for both hard rock and a fractured rock mass, this paper demonstrates the relief of subsequent blasting gases after the detonation of blastholes. This is shown through video recordings of gas ejections from a row of empty previously fired presplit blastholes located 6 to 9 meters away from the detonation edge or final buffer row of a blasthole pattern. The results clearly show that presplitting not only lowers blast vibration PPV’s but also reduces the entry of the gases produced by the detonation process into rock fractures and or open joints.

Jan 21, 2025

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Roger L. Keller

Cautious, productive blasting is employed in the adaptation of a mobile crushing system extending into a highway through cut. In Hong Kong's final chapter of infrastructure development in preparation for handover of sovereignty, the vital link to the new governing country, The People's Republic of China, is now being completed. The Ting Kau approach and Tai Lam tunnel involves the removal of 6 million cubic meters of rock by drill and blast means. For the main-cut excavation (because of removal Iogistics) a unique adaptation of a Lokotrack crushing and conveyor transfer system is being used. The characteristic narrow working area associated with through cuts, positioning of equipment, and production demand place many limiting factors on blasting. Add to this the strict criteria set by the local regulatory body, the Hong Kong Mines Division, and nearby vibration limiting structures (13mm/sec), has led to highly cautious, fine-tuned blasting.

Jan 1, 1998

By C W. "Mickey" Bradley

Thunder strikes terror in the hearts of man and has since the advent of time. We all fear the unknown; even the Greeks created a god, THOR, to be responsible for the thunder and rain. Thunder, by itself, can't hurt anyone; it is simply hot air moving very fast. Thunder, however, is caused by lightning and lightning is what we need to fear and rightfully so. Annually, lightning kills hundreds of Americans, injures another 2,000, damages or destroys approximately 30,000 structures, 1 starts thousands of forest fires and strikes mine properties over 100,000 times.

Jan 1, 1992

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By Tristan Worsey

This work was performed during the summer of 2008 during the junior year of a BS in Mining Engineering. It was observed that the mine was having a problem with back break during the blasting of development drifts. The unwanted back break was causing the mine extra costs in ventilation, ore dilution, ground support, back fill, explosives and man-hours. The blasting practices were observed for four weeks and the problems and their solutions were defined. In this paper the reasons and causes of the problem are explained with the proposed solutions to eliminate back break.

Jan 1, 2010

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By Graeme Exelby

The 4" Wassara water hammer was originally developed by G-Drill AB together with Swedish Mining Company LKAB for their underground long hole production drilling. Sandvik Rock Tools AB is responsible for the introduction of Wassara worldwide.

Jan 1, 1998

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004