Search Documents

By Francis Church Lincoln

"INTRODUCTION During the period from September 18 to November 27, 1944, the Bureau of Mines conducted an investigation and exploratory churn-drilling program in an area immediately north of the Crow Branch Diggings, a district lying approximately 2 1/2 miles southwest of the town of Livingston in Grant County, Wisconsin.The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the Nation's war prrgram.Although no mining has been done in the district in recent years the Crow Branch Diggings were an important source of galena and may be found today in the dumps remaining from old surface-mining operations.The Bureau of Mines undertook an exploratory churn-drilling program on the northwestern projection of the general strike of the digging in a zone where subsurface,lead and zinc mineralization had been reported from drilling done in the early 1900's."

Feb 1, 1947

By A. C. Smith

The U.S. Bureau of Mines constructed a large-scaJe facility to study the self-heating of a large coal mass under conditions that simulate a gob area of a mine. The insulated coal chamber can hold up to 13 short tons (st) of coal and is provided with a forced ventilation system and computer-controlled temperature and gas measurement systems to monitor the heat and mass transfer phenomena that occur in the coalbed. Three experiments were completed with high-volatile C bituminous coals that exhibited high spontaneous combustion potentials in laboratory-scale tests. In the first two tests, a sustained heating was not achieved. In the third test, temperatures throughout the coalbed increased steadily from the start, with thermal runaway occurring near the center of the coalbed after 23 days. The thermal reaction wne then moved toward the front of the coalbed. The results of these tests showed that the self-heating of a large coal mass depends not just on the reactivity of the coal, but also on the particle size of the coal, the freshness of the coal surfaces, the heat-of-wetting effect, and the availability of O2 at optimum ventilation rates.

Jan 1, 1991

By Eric G. Kok

Complying with respirable dust standards is presently a critical problem for many longwall faces equipped with double drum shearers. Results are presented of research performed to increase the quantity and optimize the distribution of the water supplied to the shearer drums to control the shearer operator dust exposure. The effect on the total respirable dust produced by the shearer was also examined. During the research effort, a simple and inexpensive manually controlled valve system was designed and implemented on a shearer to distribute the water supplied to the shearer drums. Research showed that increases in water quantities are beneficial but associated pressure increases may induce respirable dust boilover negating potential advantages. Other essential parameters such as location of shearer operator, outside spray orientation and air quantity were considered in the evaluation.

Jan 1, 1986

By J. R. Thoenen

[For several years the Bureau of Mines conducted tests on ground vibration t emanating from quarry blasting in an effort to determine an index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Invitations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

This summary of State laws or explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful In determining whether relevant statutes exist, and In locating them quickly,-with a minimum of effort. It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of those jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

By J. E. Rourke, O&apos

This report incorporates a review of available dewatering technology and an evaluation of its relevance to surface coal mines in the Interior Province of the United States. Guidelines for the selection, design and construction of dewatering systems are included. On the basis of documented experience, candidate dewatering systems were selected and evaluated with respect to their anticipated impact on the environment and mine operations. Included in the discussion is a summary of laws and regulations which can impact on dewatering operations. Following this discussion, geologic and hydrogeologic conditions within the Interior Province are described and potential dewatering problems at surface coal mines are identified. Model mines are developed which exhibit the most difficult dewatering problems identified, and it is demonstrated how available technology can be utilized to deal with these problems. Dewatering of coarse-grained, high permeability terrace deposits might be economically feasible today. Low permeability, saturated glacial tills or lake deposits appear to be significantly outside present economic feasibility for dewatering.

Jan 1, 1979

By M. Troyer

A coal shuttle car equipped with a pulsed laser optical ranging system to provide guidance for an automatic steering system was tested in production coal mining. Test results are presented for the two mines where testing took place, and some operator's reactions are included. Automatic steering control keeps the car cantered in an entry, and automatic turns are made at intersections as signaled by the operator. All other controls-tram, conveyor, brake, etc, remain manual and require operator control. Complete override of steering while in the automatic mode is retained by the operator, who may grab the steering wheel at any time and turn in opposition to the automatic signal by applying about 10 foot-pounds of torque.

Jan 1, 1976

By D. Ng

A facility to evaluate the fire endurance of mine stoppings was constructed by the Bureau of Mines in the multiple entry section of the Bruceton (PA) Experimental Mine. Stoppings up to 6 by 18 ft can be tested in a manner simulating mine conditions. The stopping is subjected to a 70-min liquid fuel tray fire with an energy output of 75,000 Btu/min. The stopping and adjacent areas are instrumented with thermocouples and heat flux gauges. Data acquisition is by an automatic data logger capable of continuously recording over 100 channels of information. Two 8-in-thick concrete block stoppings and a galvanized steel stopping were tested. A crack developed on the fire side surface of the block stoppings where the flames were most intense. However, the temperatures of the unexposed surfaces of the stoppings never exceeded 800 C and the surfaces were undamaged. The steel stopping retained its structural integrity during the test. The temperature of the unexposed steel surface reached 5000 C, but combustible materials located 1 ft from the surface did not ignite. A 3/4-in-thick coating of construction plaster was applied to the fire side of the previously tested uncoated steel stopping. The quantity of heat energy transmitted across this coated metal stopping was reduced approximately 50%. All stoppings prevented the passage of flame and smoke.

Jan 1, 1988

By Gordon R. Sima

The contract is concerned with feasibility studies, design and fabrication of a group of prototype hand-held test instruments and machine-mounted test instruments for measurement of electrical shock hazards of mining machines. An instrument for use in open pit mining machine ground wire verification was proposed, developed, built, and tested. This report presents the design and operational theory of the open pit instrument as well as information on the program to improve the original prototype hand-held machine-mounted test instruments.

Jan 1, 1977

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By Theresa Y. Schulz

It is interesting to study the noise standards that have been promulgated in the US over the last decade or so. These regulations are likely to have long-lasting impact. The Occupational Safety and Health Administration (OSHA) Hearing Conservation Amendment (March 1983) continues to have influence not only in the workplace but in the debate over new regulations. Both the Mine Safety and Health Administration (MSHA) and Federal Railroad Administration (FRA) regulatory preamble documents state the desire to be consistent with OSHA. An examination of Table 1, which compares the major components of the three regulations and the 1998 NIOSH “best practices” criteria, depicts the extent to which that intent is met. There has been some regulatory activity in the last decade which may give some hope for evolution and updating based on the wealth of science that has occurred during the last quarter of a century since the OSHA regulation was enacted. However there has also been some “back-sliding” toward more lenient standards. The MSHA noise standard made regulatory progress in September 2000 by emphasizing engineering and administrative controls, followed by personal protective equipment, in the hierarchy of noise intervention. MSHA’s requirement for technician certification (today only available from CAOHC) strengthened the training requirements for audiometric testing in hearing conservation programs and MSHA also added the requirement of dual hearing protection at 105 dB TWA. There were many subtle differences between OSHA and MSHA based on comments and a desire to clarify some of the vague aspects of the OSHA noise standard, and meet the needs of the regulated mining industry. One example pertains to the ceiling for exposures. OSHA says, “no exposures >115 dBA,” which is interpreted to mean no unprotected exposures above that level, giving credit for the assumed effectiveness of hearing conservation programs, hearing protection devices and administrative and engineering controls. MSHA specified that a “P” code1 violation be issued for any protected or unprotected exposures >115 dBA. The Federal Railroad Administration (FRA) noise standard for railroad operating employees, which went The Modern Evolution of Hearing Conservation Regulationsinto effect February 26, 2007, was expressly based on the OSHA standard but also uses MSHA for comparison. The preamble states that the FRA defers to OSHA as the “primary regulator of noise in the workplace,” but also acknowledges the need for some departure from the OSHA regulation (FRA Preamble II.B). As an example, FRA requires testing at 8000 Hz “because it will allow employers to identify hearing loss sooner.” The FRA rejected MSHA’s hierarchy of noise controls in favor of requiring specific engineering interventions and focusing on appropriate hearing protection which would still allow communication and audibility, and identification of excessive noise through employee-filed “excessive noise reports.”2 Where OSHA has no specific mandate requiring employees to take advantage of the employer-paid audiogram, it has been traditionally a condition of employment and is generally accepted that OSHA-covered workers require an annual audiogram. MSHA addressed this issue in its preamble; however, they made no significant change. MSHA employers are required to offer annual audiograms but MSHA stopped short of requiring employees to comply with annual audiometric testing. The MSHA preamble does allow that mine operators can also make audiometric monitoring a condition of employment. FRA requires employees to

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

By James A. Wasson

This report summarizes the results and conclusions reached by various investigators who have attempted to determine the extent to which hydraulic fracturing will affect the secondary recovery of crude oil by waterflooding. It also discusses the most advantageous use of this well-stimulation method in waterflood projects. A thorough search of the literature was made, and pertinent information was abstracted from appropriate reports. A carefully designed and controlled program of formation fracturing is an effective aid in waterflooding because it increases water-injection and oil- production rates. Generally, fracturing has resulted in little or no reduction in ultimate oil recovery, but under certain circumstances recovery has been substantially increased.

Jan 1, 1963

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981