Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980

By G. L. Oldright

In the first Report of Investigations of the present series?(No. 4562) the usual course of progress ill reducing the minerals of low-grade ores to their valuable metallic components had been noted as advancing along two lines to concentrate a usually diminishing percentage of these minerals to a smaller bulk of richer product, and then to smelt the smaller bulk more cheaply per pound of metal produced. Fundamental properties of lead compounds made it difficult to treat much richer lead products than are treated at present in several steps of conventional lead smelting, unless ?marked modifications were made. No limits to the richness of the feed itself' were set by the ore (Scotch) hearth; on the contrary, the richer the feed, the better the results given by the hearth. The natural field of operation of the hearth, as determined by the ores available, was seen to lie in the Central United States, with their lead concentrates containing negligible quantities of precious metals and. with few ores of such metals available for use as fluxes. It was noted) however, that even in its chosen field, the Scotch hearth, or "ore" hearths developed from them, was not always used; the usual smelting practice was followed, at times, of sintering followed by blast-furnace smelting for even rich ores.

Jan 1, 1949

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By Michael Kaplan

An investigation was conducted of the use of a mechanical rock splitter as the primary means for rock fragmentation in underground hard rock mining systems. Analyses and scale model tests showed that reasonably sized splitters that could be mounted on the booms of conventional drill jumbos were capable of fragmenting over a ton of rock per cycle. Detailed drill-split mining systems were developed for entry development, room and pillar, bench mining, and cut and fill mining. Economic analyses of these systems showed them to be generally competitive with conventional drill-blast methods. Except for bench mining, drill-split offered substantial cost savings over drill-blast. The investigation also included a technical evaluation of the mechanical splitter, an analysis of health and safety, and a determination of the potential applicability of drilling and splitting.

Jan 1, 1979

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By M. E. Poad

Structural properties of steel-fiber-reinforced shotcrete and polymer-impregnated shotcrete, both plain and fiber-reinforced, were investigated by the Federal Bureau of Mines, Spokane Mining Research Center. The research center has found that flexural strengths can be increased by as much as 106 percent, and splitting-tensile strength by 50 percent, by introducing randomly oriented steel fibers. A slight decrease of compressive strength was found in the fiber-reinforced shotcrete. Polymer-impregnated shotcrete exhibited a threefold to fourfold increase in compressive and splitting-tensile strength. The techniques of preparing shotcrete with the dry process, using both fast-set agents and regulated-set cement, are described, along with the results of physical-property testing. Physical properties include compressive and splitting-tensile strengths, tangent and secant moduli, and stress-strain curves for plain shotcrete, fiber-reinforced shotcrete, and polymer-impregnated plain and fiber-reinforced shotcrete. Flexural strengths for plain and fiber-reinforced shotcrete are also reported. Steel-fiber shotcrete is the more promising of the new structural materials for ground support, and additional research is recommended.

Jan 1, 1975

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By Ronald T. Mayerle

The Condrey Mountain RARE II area lies mostly within the Elliot Creek mining district, a significant producer of gold from placers, and gold, Silver, copper, and minor soapstone from lode deposits. No mineral production has occurred within the study area; no resources are known in the area. However, significant resources in lode and placer deposits are just outside the west and northwest boundary of the area. The Blue Ledge Mine (fig. 1, no. 15) adjacent to the western boundary, is reported to contain 226,000 ton; (205,000 t) of identified resources averaging 0.05 oz gold per ton (1.7 g/t), 2.16 oz silver per ton (/4.0 g/t), 3.5 percent copper, and 3.95 percent zinc. The mine has produced 11,131 tons (10,114 t) of ore that yielded 1,026 oz (31,908 g) of gold, 58,431 oz (1.8 million g) of silver, and 2.7 million lb (1.2 million kg) of copper. Exploration is currently underway at `he mine and vicinity, including part of the study area.

Jan 1, 1983

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By Kevin Hennings

Screening efficiency models developed to date rely almost exclusively on empirical formulas based upon large amounts of acquired operating data. A screening model was developed using a combination of empirical coefficients and explicit mathematical expressions which quantify screening phenomena. A series of screening tests was run to supply data for purposes of correlation and empirical coefficient evaluation. The model has been implemented as a digital computer program. The validity of the modeling procedure has been established by laboratory testing. Results generated by the model have been used to compile an applications handbook, which can be used to predict screening performance in lieu of using the computer program.

Jan 1, 1982

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946