Search Documents

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By D. K. Caddel

Several problems exist with the present design of coveralls used by miners in low coal (seam height 48 inches or less). The back portion of the coveralls often tears when roof bolts or rough areas in the roof are hit. Movement in the shoulder area is restricted. Female low coal miners find it difficult to purchase coveralls that fit properly, and must remove both their hard hat and safety belt in order to urinate and defecate. The objective of this research was to design coveralls which would alleviate these problems. The following features were incorporated into the coveralls; padding in the upper back area to avoid tearing, an action pleat in the shoulders to increase mobility, an inseam zipper to more easily allow miners to perform their bodily functions, and reflective tape to increase visibi¬lity of the miner. A heavyweight denim fabric was used to increase warmth and durability of the coveralls. The coveralls were assessed K long four parameters (comfort, safety, worker productivity, and fabric suitability) using both an in-field assessment by low coal miners and simulation studies. The experimental coveralls proved superior to conventional coveralls along all four parameters. Work clothing sizes for female miners were developed.

Jan 1, 1982

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By D. A. Reynolds

A few studies on the relationship of the fusion temperature of the ash on coke to that of the corresponding coal have been made on commercial high-temperature cokes. H. J. Rose3/ in 1921 compared the fusion temperatures of the ashes of 10 coals and the cokes produced from them and concluded that they were in such hose agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coal. As the ash of a coal and that off tie coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and grinding preparatory to sampling. Pieters6/ found that coke ash was contaminated in this manner up to 0.4 percent. Extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible.7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coal, especially if the fine grinding of the coke was done by rubbing -surfaces of iron, as in a disk pulverizer or bucking plate.

Jan 1, 1940

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By L. H. Duschak, C. N. Schuette

In the years 1850 to 1923, the United States produced 2,426,000 flasks- (73,600 metric tons) of quicksilver worth $120,500,000. California yielded 2,195,000 flasks of this total; the remainder came from Texas, Oregon, Nevada, and A.rizona. Most of this metal has been extracted from low-grade ores, those containing less than 0.5 per cent mercury or 10 pounds per ton. The finished product or " virgin metal" is made at the mine and shipped in flasks. Quicksilver is unique in being the only metal that is liquid at ordinary temperature. Because of this and other physical and chemical properties, it is perhaps more indispensable to industry than any other metal. On the other hand, the quicksilver industry of the world is of vanishing significance" when compared to the major mineral industries with respect to quantity and value of product, capital invested, or the number of men employed. The peculiar value of quicksilver is due to the fact that in some of its applications no substitute is available and in others the substitutes would be unsatisfactory or extremely expensive. Scarcely a branch of science or industry fails to make some use of mercury or its compounds. As a detonator for explosives, mercury fulminate holds first place and in safety and reliability could be replaced only by the highly expensive silver fulminate.t vThrough its use in detonators and in the metallurgy of the precious metals quicksilver is of special importance to mining. In medicine,in the manufacture of electrical apparatus, the production of pigments and antifouling paints, and the general field of experimental science quicksilver is equally indispensable.

Jan 1, 1925

By Hon-Yim Ko

1972 constituted the second year of the projected five-year study on constitutive relations of coal. The schedule adhered closely to the five-year outline which is summarized in Table 1. This chapter is intended to serve as introduction and concise synopsis of the year's activities and results, which are presented in greater detail in the following chapters, which have been contributed by the individual researchers in charge of the various aspects of the project under study. Coal Sources, Material Procurement, and Sample Preparation Most of the studies performed during 1972 were done on coal from two sources: the Old Ben Mine #22 in Illinois, and the Bruceton Mine in the Pittsburgh seam of Pennsylvania, which may be considered typical of coal sources of economic importance in the Midwestern and Eastern part of the U.S. These two mines have proven to be reliable suppliers of coal material for our research. We have been able to establish good working relations with their personnel and feel that we can continue to count on their cooperation and help.

Jan 1, 1972

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By W. A. Dunkley, W. W. Odell

About two-thirds of the manufactured gas supplied to the public by the gas plants in the Illinois district is cnrbureted water gas. The leading generator fuel is coke, ma.de in by-product c.oke ovens or in retorts, chiefly from eastern gas coals. During the fall and winter of 1917-18, when the demand for coke by war industries and the restrictions of the Fuel Administration in connection with the transportation of coke from eastern States made it almost impossible for many gas companies to obtain their coke requireml'nts, several water-gas plants had to use bituminous coal as generator fud. Many operating difficulties were encountered, some of which were solved more or less satisfactorily in different plants. A number of plants attacked the problem rather blindly because facilities for making tests were lacking and because technical men were too busy with labor and supply problems to study thoroughly the conditions involved or to ascertain what other plants had done with this fuel. It was therefore with the hope of assisting the gas industry during this critical period, and of promoting the use of Central District coals for gas making, that the Illinois Mining Investigations, a joint agency of the U. S. Bureau of Mines, the University of Illinois, and the Illinois Geological Survey Division undertook the, tests discussed in this paper. • This report was compiled under the auspices of a technical committee appointed by Gov. Frank 0. Lowden to promote the use of Central District coals in gas manufacture as a war measure. This committee included the following representatives of the various agencies concerned: U. S. Bureau of Mines, E. A. Holbrook and W. W. Odell; Illinois Gas Association, C. W. Bradley and R. B. Harper; University of Illinois, Dean C. R. Richards, Prof. S. W. Parr, and Prof. H. H. Stoek; State Geological Survey Division, F. W. De Wolf, G. H. Cady, a.nd W. A. Dunkley. F. W. De Wolf was chairxnan of the committee and E. A. Holbrook was secretary.

Jan 1, 1924

By Larry A. Haas

Carbonyl sulfide (COS) was decomposed to sulfur and CO in a silent electrical discharge. A threshold of about 4 kv at 60 Hz was required to dissociate the gas in a laboratory ozonizer at 790 torr with electrode gaps between 1 and 5.5 mm. Above the threshold value, the reaction rate increased with increasing voltage with helium or nitrogen diluent. With the latter diluent, higher voltages had to be applied to obtain the same yield in the 4-to 12-kv range. The COS decomposition rate increased with COS concentration, but a saturation value was reached at about 10 pct COS. The reaction rate decreased at low linear gas velocities as obtained at lower gas flows, larger electrode gaps, or larger reactor volumes. Increasing gas temperature also decreased the decomposition rate. The presence of solid adsorbents such as quartz wool, bauxite, or charcoal had no significant effect on the reaction rate. The addition of S02 did not affect the COS decomposition rate, but small amounts of water decreased the reaction rate. Over 50 pct of the COS was decomposed at room temperature and atmospheric pressure in a l7-kv ozonizer using a gas containing 0.9 pct COS in helium flowing at a rate of 0.3 liter/min. The average current was less than 5 ma. This method has possible application in eliminating the toxic air pollutant, COS, which is generated in petroleum refineries and in processes involving reactions between sulfurous and carbonaceous materials. Carbon monoxide that is formed can be further oxidized to CO2 after the collection of elemental sulfur.

Jan 1, 1972

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By W. F. M. GOSS

For the purpose of procuring data that could be used in estimating the value of the briquetting process as applied to American fuels, the United States Geological Survey, in cooperation with other interests, began in 1904, at the Louisiana Purchase Exposition, certain experiments involving the production and use of bituminous-coal briquets. It installed at St. Louis, and later at Norfolk, machines for the manufacture of such briquets, and the output of these machines has been tested in locomotive service on several different railroads in comparison with natural fuels. An elaborate and carefully executed series of tests involving the use of natural coals and of briquets made from the same coal, previously crushed, was carried out on a locomotive mounted at the testing plant of the Pennsylvania Railroad Company at Altoona, Pa.; and some preliminary experiments involving the use of briquets in marine service were made in connection with one of the Government's torpedo boats. A description of these tests is presented herewith. The results sustain the following general conelusions: 1. The briquets made on the Government's machines have well withstood exposure to the weather. and have suffered but little deterioration from handling. 2. In all classes of service involved by the experiments, the use of briquets in the place of natural coal appears to have increased the evaporative efficiency of the boilers tested. 3. The smoke produced has in no test been more dense with the briquets than with coal; on the contrary, in most tests the smoke density is said to have been less when briquets were used. 4. The use of briquets increases the facility with which an even fire over the whole area of the grate may be maintained.

Jan 1, 1911

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By James C. Fowler

This report contains a description of the contract activities performed by ENSCO, Inc. under contract H0292025. The purpose of this project was to prove the feasibility of detecting hazards in a coal seam using a synthetic pulse radar. This work was conducted in three phases. The first was an analysis of the types of errors which might cause problems. The second was to build a breadboard radar and the third phase was to conduct a field test with the system. The work from each phase is discussed and the results of the field tests are presented. These results show propagation of the radar signal through 200 feet of coal along with reflections from 50 feet away. The final section contains recommendations for future development.

Jan 1, 1981

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

By J. A. Kosek

Work has been conducted under Bureau of Mines Contract Number HO 357078 to develop instruments for detecting CO, NO and NO2 in a mine atmosphere, using fuel cell technology. The approach has been to optimize the fuel cell sensor configuration for the specific detection of CO, NO and NO2 in the presence of other mine gases utilizing recent advances in catalyst, electrode and solid polymer electrolyte membrane technology. Para-metric testing has been conducted on three electrode sensor cells to define performance and life characteristics as a function of temperature, feed flow and applied sensor voltage. Extended life testing has been performed on sensor cell configurations exhibiting favorable characteristics. Reliable, efficient gas sampling and electronic control circuitry has been fabricated for use with the sensor cells, and integrated into devices to meet the performance and design specifications for portable, battery-powered, hand held direct indicating gas detectors for use underground. Twenty of the production-type, direct indicating CO detectors have been tested and delivered to the Bureau of Mines under the present contract. Three prototype diffusion head CO monitors have also been delivered for evaluation under the pre-sent contract. The gas sampling pump and related parts have been replaced by a diffusion tube assembly in which CO reaches the sensing electrode surface by diffusion alone. In addition, delivery will be made of ten direct-indicating nitric oxide detectors and ten direct-indicating nitrogen dioxide detectors. These instruments are very similar in design to the direct indicating CO detector.

Jan 1, 1979

By Merle L. Bowser

The Bureau of Mines has developed a portable recording methanometer that utilizes the Bureau's methane sensor. The methanometer can operate continuously for at least 30 hours on small, sealed, rechargeable lead-acid batteries.

Jan 1, 1969