Search Documents

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department?s Bureau of Labor Statistics? Census of Fatal Occupational Injuries, Survey of Occupational Illnesses and Injuries, and Current Population Survey. Between 1992 and 2002, 3378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 to 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992?1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002 but showed overall improvement from 1995 to 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100 000 workers. In addition, 46 598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. The research of the National Institute for Occupational Safety and Health aimed at evaluating commercially available overhead power line proximity warning alarms is described. This paper is expected to be the initial step for eventual development of a performance standard for such systems.

Jan 1, 2008

By Robert D. Saltsman

Two modes of seal application were identified, and promising state-of-the-art seals of both types -shaft and drum -were selected for initial rating by non-destructive testing. Only one shaft seal survived the initial test, and a search was made for other candidate seals including new seals. One new type of seal was found that gave promising enough operation, as both a shaft and drum seal, to be recommended for installation in prototype wet-head machines.

Jan 1, 1975

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

The Appalachian Mountains divide Pennsylvania into two distinct coal regions, bituminous and anthracite. The western region of the the state, where the majority of bituminous mines are located, is characterized by mountains and gently rolling hills. Bituminous coal seams underlie about 12,000 square miles in 28 counties. The anthracite coal region, located in the northeast, covers approximately 3,300 square miles. This area contains more than 20 different coal beds that vary in thickness from a few inches to 50 or 60 feet. The anthracite region is characterized by steeply pitching seams that require highly specialized mining techniques and present unique challenges for solving problems such as the mine subsidence associated with abandoned underground anthracite mines. For more than a century, coal has played a major role in the economic and industrial development of Pennsylvania, particularly the steel industry. Estimated bituminous reserves total 23 billion tons, or 5.3 percent of U.S. reserves, and anthracite reserves total 7.1 billion tons, or 97 percent of U.S. anthracite reserves. Pennsylvania received conditional approval of its regulatory program July 31, 1982. Pennsylvania's Abandoned Mine Land Program was approved on the same date.

Jan 1, 1992

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By Hillary W. St. Clair

Mining activity began in colonial times with ironmaking operations scattered along the eastern seaboard. Iron furnaces and forges manufactured iron implements from bog iron ores using charcoal from the extensive forests as a fuel. Lead ores were mined in the Mississippi Valley and copper ores in the Lake Superior region. However, the real beginning of the American mining industry did not occur until the 19th century. The history of American mining is organized around three epochal events. The first was the discovery of gold in California in 1848, which marked the beginning of a period of apprenticeship in mining and metallurgical techniques. The second was the discovery of the fabulous Comstock Lode in western Nevada in 1859, which expanded mining throughout the Far West and led to large-scale underground mining and the development of smelting techniques for lead, silver, and copper ores. The third event was the building of a transcontinental rail-road system after the Civil War, which brought about the consolidation of the industry from a large number of independent mines, mills, and smelters into integrated operations run by large corporations. Thus developed the mining industry that today supplies the energy and critical materials for the great-est industrial complex the world has known.

Jan 1, 1977

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By Yumi Nakashima, Setsuo Maeda

Vibration magnitude and frequency of the z-axis vehicle seat are time-variant, which are influenced by not only vehicle vibration characteristics themselves but also road surfaces, speeds and the human body. There is little in the current reporting about evaluating and analyzing automobile seat vibration that focuses on the time-variant. Yaguchi et al.1 has proposed a method to evaluate automobile seat vibration that is based on judgments using a subjective mental state. Their method focuses on the time-variant magnitude of the peak frequency on a power spectrum density. However, their method has no consideration of all the frequency contents of the discomfort, nor comparison between different peak frequency vibrations. Suzuki2 has emphasized that the vehicle vibration should be judged by a series of vibration stimuli to evaluate, because the vehicle vibration is time-variant, which isn’t a matter of the relationship between a single vibration stimulus and a subjective response. He clarified that the human sensation to the vehicle vibration discomfort changes every moment showing the relationship between the frequency-weighted r.m.s. acceleration calculated every 5 seconds and the category judgment to vehicle vibration discomfort every 5 seconds. However, his study doesn’t show what parameter connects to the subjective final judgment to vehicle vibration. Therefore, we applied the method similar to ISO100563 considering the time-variant to the vehicle seat z-axis vibration evaluation. The new method for the vehicle seat vibration considering the time-variant was examined on the hypothesis that the final subjective evaluation must be conducted from the judgment summarizing a series of vibration stimuli. Methods The vibration bench system, which reproduces the movement of a vehicle floor, was used for the experiment with the single-axis (vertical direction) four-post road simulator system, which is usually used for a car, as shown in Fig.1. The experiment was done on the right side of the vibration bench using the floor vibration which was 5.5 minutes, 0.822 m/sec2 (Wk) over the range 0.5-20Hz with 4 male subjects (age ave21.5, SD0.5, weight ave75kg, SD7.91kg, height ave166.8cm, SD5.2cm) and 4 suspension seats. As Fig.2 shows, subjects evaluated the degree of discomfort every 5 seconds to each seat vibration measuring the seat z-axis vibration acceleration. [ ]

Jan 6, 2006

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

This Bureau of Mines report is a reference manual of procedures used by the Bureau's Twin Cities Mining Research Center for obtaining rock properties. Included in the report are discussions on the usage of each property, descriptions of the general test methods for obtaining the properties, and instructions for performing the tests. The Instructions embrace details of the specimen configuration, test apparatus, test procedure, test conditions, and calculations needed to achieve satisfactory results. Although the procedures presented in this reference manual generally conform to recommendations of the ASTM Administrative Committee on Standards, they are not purported to be standards.

Jan 1, 1974

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.