Search Documents

By D. E. Sullivan

The Bureau of Mines investigated the availability of potash from 68 mines and deposits in 12 market economy countries (MEC's) containing, at the demonstrated resource level, approximately 11.7 billion metric tons (mt) of potash in assay terms of contained K2O; K2O as used by industry as a standard of comparison for the different forms of potash. These resources include almost 190 million mt in the United States, 9.63 billion mt in Canada, approximately 430 million mt in Western Europe (France, Federal Republic of Germany, Italy, Spain, and the United Kingdom), 1.24 billion mt in the Middle East (Israel and Jordan) and over 220 million mt in other countries (Brazil, Chile, and the Congo). This analysis his determined that future production of potash in MEC?s will most likely continue to be from the large resources associated with producing operations in Canada. Based solely on the demonstrated resources included in this study, potash mining in the United States would decline while overseas production from MEC's can continue into the next century at near current production levels. However, timely development of new or inferred resources would offset any such decline. Producing mines in Canada have the resources to increase and maintain increased production well into the next century. For U.S. potash users, Canada is a long-term stable and secure source.

Jan 1, 1986

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By T. A. Henrie

The Federal Bureau of Mines has investigated methods of sodium reduction of titanium chlorides to produce high purity titanium metal (14).4/ This investigation was made to obtain a better understanding of the reactions involved in sodium reduction of titanium chlorides and was part of the Bureau's activities toward improving the technology of titanium. Theoretical and experimental evidence show that sodium reduction of titanium tetrachloride occurs by stepwise reactions. The first stage reduction between sodium vapor and vapors of titanium chlorides produces titanium di-and trichlorides which subsequently condense with sodium chloride to form a salt mixture. The second stage reduction takes place in the condensed salt mixture between sodium and titanium subchlorides. Final reduction is a heterogeneous reaction between two separate phases, the a phase which consisted of sodium dissolved in sodium chloride and the ß phase titanium subchlorides dissolved in sodium chloride. The mechanism of the heterogeneous reaction between these phases is electrochemical in nature. The model proposed is a galvanic reaction at the interfacial region.

Jan 1, 1960

[ ]

Jan 1, 2011

By Andrew Allan

[This report describe the first experiment of the Anthracite Research Laboratory, Bureau of Miners, in attempting to reduce underground-mining costs and conserve anthracite as a natural r-source by introducing now minim methods. The work war, dons in cooperation with one of the large anthracite-producing companies. It applies to productive mining, characterized by comparatively low cost, per ton and high production per man, as differentiated from development mining, which is always necessary before the, productive or retreat phase can begin. The system d scribed in this report is believed to be generally applicable to beds pitching 70° to 90° and, under certain conditions, to beds pitching loss than 70°. After development hate been completed, an openings is made, extending the full width of the 9- to 10-foot coal bad and reaching from the haulageway to the vertical limits of the solid coal. Long drill holes (20 to 50 feet) charged with about one stick of permissible explosive riper foot of length are fused to break the coal. Once broken, the coal is loaded onto a shaker conveyor by gravity and thence into mine: cars. The coal is mined retreating in 15- to 20-foot sections that are broken and loaded onto the conveyor through a specially constructed chute. In the Bureau?s experimental work, the height of sections arse ranged from 35 to 60 fact, depending on the geologic extent of the coal bed.]

Jan 1, 1952

By K. J. Liles

The U.S. Bureau of Mines evaluated the physical properties of ceramic particulate composites made from titanium nitride (TiN), alumina (AI203), and aluminum nitride (AlN) as part of a program to meet the high-performance demands on structural materials for new and emerging technologies. Samples containing from 20 to 80 wt pct TiN were pressed and fired, and their composition, Vickers hardness, modulus of rupture (MOR), and fracture toughness were determined. X-ray diffraction and scanning electron microscope (SEM) analyses showed that, depending on the amount of TiN added, the microstructure of the samples consisted of either a titanium-aluminum-oxynitride (TiAlON) particulate in a spinel matrix or a spinel particulate in a TiAlON matrix. The best results of the physical tests were achieved on a mixture of 40 wt pct TiN, 30 wt pct A1203, and 30 wt pct AIN. Sintering aids were added in 1-and 3-mol-pct increments to the 40-30-30 mixture to determine their effect on microstructure and physical properties. Results of an analysis of variancf' on a 4 by 4 factorial analysis showed significant effects on density, MOR, and Vickers hardness.

Jan 1, 1989

By F. M. Jenkins

Longwall mining systems are used to mine approximately 50 pet of the world's total underground coal production. Single entries are the predominant method of longwall development in Europe and Asia, where mining conditions are more severe than those encountered in the United States. During the 1970's and early 1980's, the U.S. Bureau of Mines and the U.S. mining industry invested nearly $20 million in single-entry and related research. This report reviews the accomplishments of single-entry research in the United States and describes two U.S. single-entry field projects: the Sunnyside single-entry project in central Utah and the tunnel-boring project in northern West Virginia. Also discussed are a single-entry study conducted by North American Mining Consultants (NAMCO) and a single-entry design study conducted by Ketron, Inc. This Bureau report compares the resulting technology with European counterparts to further assess the utility and efficiency of U.S. systems.

Jan 1, 1990

By Jr. Gabler

World resources of platinum-group metals appear ample for the foreseeable future; however, political and economic events in the last two decades have caused concern over the availability and reliability of an uninterrupted supply. Because of this concern, the U.S. Congress requested that the U.S. Bureau of Mines initiate a study of the flow of platinum-group metals in the economy that would delineate and quantify the production areas in which metal values are lost. As a result, the Bureau has developed a computerized commodity flow model for strategic and critical materials. Major attributes of this flow model are as follows: (1) it is generic and applicable to most commodities and (2) it can be updated as supply, demand, and/or production data change. The original model developed for cobalt, with slight modifications, was used to track the flow of platinum-group metals. This report follows the flow of platinum-group metals through their metallurgical, catalytic, and chemical applications and highlights areas in which significant losses occur because of downgrading, export, or disposal. The study indicates that materials containing about 63,426 kg of platinum-group metals were lost or could not be traced in 1989, representing about 63 pct of U.S. domestic consumption.

Jan 1, 1991

By BUREAU OF MINES

PLATINUM

Feb 1, 1922

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923

By W. W. Adams

This bulletin covers all mines in the United States that were operated in 1936 to produce metallic ores and all mines that were operated to produce nonmetallic minerals other than coal, stone, sand, gravel, or their products. Reports from mine operators revealed a better safety record for fatal accidents in 1936 than in any other year except 1934 during the 26 years for which annual surveys of accidents in the mineral industries of the United States have been conducted by the Bureau of Mines. On the other hand, the record for nonfatal injuries, although better in 1936 than in any year prior to 1930, was not as good as it was from 1930 to 1935, inclusive.

Jan 1, 1939

By S. P. Holt

The Salt Chuck mine is on the east bank of the Salt Chuck, a salt-water inlet at the head of Kasaan Bay, Prince Edward Island, Southeestern Alaska. The deposit was worked at intervals from 1905 until. 1941. Early ship-ments of hand-sorted ore are reported to have assayed about 4 percent copper, 0.15 ounce gold, and 0.15 ounce silver. The total mine production up to 1941 is reported to have been 326,000 tons containing 6,200,000 pounds of copper. During December 1942 the Bureau of Mines cut a 15-foot channel sample on the surface and channel samples from headings on the 300-foot level. In July 1943 a development project was started. Thirteen diamond-drill holes totaling 1,550 linear feet were drilled from underground stations on the 200- foot and 300-foot levels.

Jan 1, 1948

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By William D. Dodge

A typical quality program plan is presented for explosion-proof (XP) electrical enclosures. The plan is suggested for manufactures of XP enclosures which are to be certified by MSHA for mining use. The plan describes the quality system, organization and implementing mechanisms which are to be applied in the manufacture and delivery of certified XP enclosures. Example forms and example procedures are included.

Jan 1, 1984

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Lenore Rainey Christian, J. Feldermann

"Interest in the fine structure of soots and carbon blacks is motivated by a variety of possible applications. The structure provides information on the origins of the particles and on their adsorptive and reactive properties. This paper describes a method for quantification of the structure of soots and carbon blacks based on direct electron microscopic observation followed by image analysis of these materials. High-resolution transmission electron microscopy (HRTEM) provides a very detailed observation of particle structure. The differences in soot structure, because of its complexity, may not be easily quantifiable with the human eye; therefore, high-level computer software has been used to manipulate HRTEM images. This technique involves the application of fast Fourier transforms (FFT) to single particles and the measurement of characteristic parameters such as interplanar spacings and crystallite sizes from these particles. The methodology and application of this characterization technique are presented here. Results are shown for dif¬ferent samples obtained from soot and carbon black particles selected to illustrate the capabilities of the methodology. Quantitative information can be obtained on structural characteristics, e.g., interplanar spacing, circularity, orientation, elongation, and length distribution of lattice fringes, as well as on the fractional coverage of the extracted pattern. c 1996 Wiley-Liss, Inc.This paper presents a combination of techniques for recognizing and classifying different carbonaceous materials, using their structural morphology. A new method to assess and quantify the parameters which define such structures is proposed and discussed. The technique is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, cokes, chars, etc. possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure (Buseck and Bo-Jun, 1985; Buseck et al., 1987). The carbon structure has been variously described as turbostratic (Oberlin, 1989) or as crumpled sheets (Rouzaud et al., 1991) to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers, but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as on the composition of the source of the carbonaceous material. The value of the electron microscope in studying the morphology of such materials has been well-established, and abundant information is available (Ishiguro et al., 1991; Lahaye and Prado, 1978; Buseck, 1992).The use of HRTEM has brought further insight into this matter. Qualitative assessment of the structural order of such materials has been attempted over a long period of time in order to differentiate between various sources or treatments. There is, to date, no successful method available for quantifying the structural characteristics of various carbonaceous materials. This paper presents a technique which is able to recognize dif-ferent materials and to quantify the structural parameters of those materials using HRTEM and computational image analysis, including pattern recognition techniques.In the case of perfectly ordered graphitic crystals, electron diffraction is widely used for obtaining details on structure. Analysis of diffraction patterns can reveal parameters such as interplanar spacing, d002, crystallite size along the c-axis, Lc, crystal size in the plane of the layers, L., mean number of crystallites, Nc, etc.Complicated electron microscopy methods such as defocusing, tilted illumination, axial illumination, etc., often have to be used in order to characterize complex materials such as randomly oriented crystals in soots and carbons. Obtaining the right fo"

Jan 1, 1998