Search Documents

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By J. W. Thompson

BURYING DEAD MINERS. BURYING BODIES OF DEAD MINERS. REVISED STATUTES (HURD) 1874, P. 263. SEC. 22. LIABILITY OF RAILROADS, ETC., FOR BURIAL EXPENSES.-When any railroad company, stage or any steamboat, propeller, or other vessel engaged in whole or in part in carrying passengers for hire, brings the dead body of any person into this State, or any person dies upon any railroad car or in such stage, steamboat, propeller or other vessel in this State, or any person is killed by cars, or machinery of any railroad company or by accident thereto or by accident to or upon any such stage, steamboat, propeller, or other vessel, or by accident to or in or about any mine, mill or manufactory,* the company or person owning or operating such cars, inachinery, stage, steamboat, propeller, or other vessel, mine, mill or manufactory shall be liable to pay the expenses of the coroner's inquest upon and burial of the deceased and the same may be recovered in the name of the County in any court of competent Jurisdiction. NOTE--The original Act of February 15, 1855 (Laws 1855, p. 170), makes no reference to the dead bodies of persons killed" by accident to, in or about any mine."

Jan 1, 1919

I. Domestic Production and Use: In 1981, 13 companies operated 32 primary aluminum reduction plants, with 3 firms accounting for 58% of production, Washington, Oregon, and Montana accounted for 32% of the total production; Texas, Louisiana, and Arkansas 16%; Tennessee, Alabama, South Carolina, and North Carolina 17%; other central and eastern States 35%. Based on published producer prices output of primary metal in 1981 was valued at over $7.5 billion. Aluminum consumption by 25,300 firms was centered in the East Central United States. Packaging accounted for an estimated 30% of domestic consumption in 1981, building 21%, transportation 18%, electrical la%, consumer durables 8%, and other uses 13%

Jan 1, 1982

By Shiro Watanabe

To determine the potentialities of nickel as a substitute for cobalt in catalysts for the synthesis of hydrocarbons from carbon monoxide and hydrogen, RESULTS The maximum oil yields obtained in bench-scale equipment were as follows: Using 100N1:20Mn:100 kaolin:200 diatomaceous earth catalyst, a maximum yield of 133.8 cm.3/m.3 of pure CO+2H2 was obtained from one pass of the feed gas, With a nickel:cobalt mixed catalyst (Ni:Co - 3:7) having the composition 100(Ni+Co):8MgO: 5Th02:200 diatomaceous earth, a maximum of 172.2 cm.3/m.3 of pure C0+2H2 was obtained.

Jan 1, 1951

On June 20, 1972, Ocean Energy was awarded Contract No. H0220055, entitled Portable Task Luminaire System Development. Initially, this was a 12 month program consisting of three phases: Phase I -- Design of the Luminaire System and Battery Chargers, Phase II -- Fabrication of Prototype Units, Phase III -- Fabrication of Production Prototype Units and Battery Chargers. In addition to developing the Portable Task Luminaire System, however, this contract was amended a number of times in the course of the program to include the development of a Low Coal Portable Task Luminaire, a Rib Mounted Luminaire System, and a Machine Mounted Luminaire System, all based upon the same high frequency fluorescent lighting and safety technologies involved in the Portable Task Luminaire. This report covers the activities of this program as amended, and includes the development and fabrication of all of the systems. This report constitutes the final fulfillment of the contract.

Jan 1, 1974

By D. A. Keefe, O&apos

The electrowinning of beryllium from beryllium oxide (BeO) using a molten-salt electrolyte composed of 56 LiF-37 BeF2-7 BeO (mole-percent) was investigated. Anodes made of porous carbon were found to be superior in current-carrying capacity and gave a lower cell voltage than other types of anode material tested. When porous carbon anodes were used) the resultant increase in anode area prevented anode passivation. The cell voltage was 3.3 volts) and electrode current efficiencies of 50 to 70 percent were obtained. The electrodeposited beryllium was recovered as beryllium powder or was coalesced to metal beads by heating to 1,300° C.

Jan 1, 1970

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By James C. Barker

A uniquely mineralized area extends from northwestern Canada through Alaska into eastern Siberia. Some of the metals found there are relatively rare in the conterminous United Stales. Among these are cobalt, the platinum-group metals, and chromite. Geologic evidence suggests that cobalt and the platinum-group metals may be present in deposits that could constitute nationally important reserves. Chromite in potentially minable deposits is known, but it may be relatively less abundant. Limited reserves of these metals have been delineated, but most of the favorable terranes and reported occurrences throughout the vast expanse of Alaska remain unexplored. As part of the mineral studies mandated under the Alaska National Interest Lands Conservation Act, the Bureau of Mines' Alaska Field Operations Center and the Bureau's research centers at Albany, Oreg., and Reno, Nev., are cooperating in a long- range program to investigate occurrences and delineate reserves of cobalt, the platinum-group metals, and chromite in Alaska. Studies of other critical and strategic minerals will be phased in during succeeding years, as ongoing projects are completed. This first in a series of annual reports summarizes available information about deposits and past production of cobalt, the platinum-group metals, and chromite, and describes current and planned Bureau investigations of these minerals.

Jan 1, 1981

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By Sean Gallagher

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic.

Jan 1, 1998