Search Documents

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

The 1965 Lignite Symposium, the fourth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. Them 7 symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including inspection of (1) the 200-megawatt, pulverized Lignite-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glenharold mine of the. Truax-Traer Goal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydro-electric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and des¬cribes some systems of transportation `utilizing rail haulage, ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By William R. Hardwick

Present information indicates that a copper deposit can be safely fractured with a nuclear explosive and the copper successfully recovered by the in-situ leaching method. The process is not yet at the stage where it can be presented t ) the mining industry as a technique proven in all its aspects, but it is a method with high success potential. Unknown factors must be evaluated by a full-scale test before the economics or the extent of the use of the method by the mining industry can be predicted. Preliminary calculations indicate that the cost of fracturing a copper deposit nuclear explosives may range from l.8 to 55.2 cents per ton or in some case: less than a cent per pound of recoverable copper. Copper may be recovered at less cost than by conventional methods. Deposits with 4 pounds of recoverable copper may be economic and production from a deposit may begin in less than half the time required for conventional methods.

Jan 1, 1967

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By Peter J. Clarke

The petroleum industry continued to be the most important mineral activity in Bahrain during 1978-79. Revenues generated by the petroleum sector increased from $378 million' in 1977 to an estimated $419 million in 1978 and approximately $522.5 million in 1979, despite decreasing production over the 2 year period. There were two oilfields that produced revenues for Bahrain, the Awali oilfield, the nation's only onshore producer, and the Abu Sa'fah oilfield, located in the Persian Gulf, north of Bahrain, The Await oilfield has been decreasing output from a high of 27,973,000 barrels in 1970 to 19,000,000 barrels in 1979. Bahrain shared the revenues from the Abu Sa'fah oilfield with Saudi Arabia, as settlement of an ownership dispute. For the first time, in 1978, revenues from the Abu Sa'fah oilfield represented over 50% of the total receipts from the petroleum sector. The years 1978-79 saw the gradual takeover of the Bahrain Petroleum Co. (Bapco), formerly a subsidiary of the California Texas Petroleum Co. (Caltex), by the Government-owned Bahrain National Oil Co. (Banoco). By yearend 1978, Banoco owned 60% of Bapco, and Caltex the remaining 40%. The Government-owned company controlled exploration concessions, managed domestic marketing of petroleum products, and controlled natural gas production and marketing. On December 15, 1979, the Bahrain Government completed full takeover of the Bapco operations. Bapco will continue to own and operate the 250,000-barrel-per-day oil refinery located near Sitrah, as well as handle foreign marketing of petroleum products.

Jan 1, 1981

By Khamis Y. Haramy

This Bureau of Mines paper describes the use of the borehole shear tester (BST) In mines. Assembly and procedure sections explain how the equipment is assembled and used properly. Schematics of the BST, limitations, test hole specifications, data recording and calculations are all explained briefly, and an example of the data collecting and calculations is given to assist understanding.

Jan 1, 1981

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By Whitman E. Brown

"As part of a Nation-wide program of the United States Government to develop natural resources, funds were made available to the Bureau of Mines for the investigation of the ""Reduction of Iron Ores by Solid and Gaseous Fuels."" These investigations are concerned with the direct production of iron from its ores without the use of a blast furnace. Many processes have been proposed for the low-temperature reduction of iron oxides, but few have been developed to commercial use. High-quality sponge iron is produced com-mercially only in Sweden.The cost of iron production depends in part on the grade of the ore and increases with decrease in grade. The substitution of cheap natural gas in a sponge-iron process for expensive coke in smelting in the blast fry pace would partly compensate for the use of low-grade ores. If a process can be developed in which inexpensive natural gas can be used as fuel and reducing agent, the large deposits of low-grade iron ore and the natural-gas resources of east Texas may be utilized in the commercial production of sponge iron.Sponge iron may possibly be used to supplement scrap iron, pig iron, or, in special instances, wrought iron. Sponge iron will vary but slightly in composition and will contain little or no nickel, cobalt, manganese, copper, and other allowying metals. It is becoming increasingly difficult to obtain choice scrap iron of nonalloy composition. Pig iron contains 1.5 to 3.0 percent silicon and 3.0 to 4.5 percent carbon. Sponge iron generally contains less carbon than pig iron.The Madaras Steel Corp. in Longview, Tex., built a set commercial-scale sponge-iron plant which was intended to be operated in connection with a steel foundry. The process is based upon the reduction of preheated iron ore, with hot reducing gases under pulsating pressure. Although the Madaras Corp. had previously experimented with the production of sponge iron by reducing the ore with pure hydrogen, several attempts to use a re-formed natural gas as the reducing agent in this pilot plant were unsuccessful. The Bureau of Mines leased this plant and conducted an extensive investigation of the Madaras process on a semicommercial scale.The experiments were not entirely satisfactory, partly because of mechanical difficulties and partly because the reducing gas was not of the best quality. However, much information on the production of reducing gas by re-forming natural gas and on the reduction of iron ore with re-formed natural gas was obtained.The sponge iron produced contained approximately 0.1 percent phosphorus; and, after melting in an electric furnace, the iron contained approximately 0.15 percent phosphorus. The results of attempts to improve the ore by ore-dressing methods were not encouraging."

Aug 1, 1946

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control of anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/. These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the mounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating beers dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By O. Q. Leone

A processing unit was developed for the complete cleaning of titanium alloy chips. The process uses solvent degreasing, magnetic separation, and anodic solution of nonmagnetic impurities in 10 weight-percent sulfuric acid. Vacuum arc-melted ingots weighing approximately 10 pounds each were prepared from cleaning chips according to ingot specifications.

Jan 1, 1973

THIS bulletin presents all analytical and lest methods regularly used by Bureau of Mines laboratories for characterizing coal and coke. To provide better service to coal producers and consumers, the scope of this bulletin has been expanded to include important test methods used to evaluate coal properties for commercial processing. The methods described will prove valuable to all persons interested in analyzing and testing coal and coke.

Jan 1, 1967

By Melford H. Salsbury

The maximum net return from the sale of ores and concentrates of gold, silver, copper, lead, and zinc accrues to the producer when these mine products are marketed to the best advantage. Data are presented that the producer, especially the small mine operator, can use to survey available markets and make a preliminary estimate of the net return to be expected from an ore, on the basis of typical mill, smelter, and freight schedules. A review of the industry is presented by States in which recent production statistics are given, marketing facilities are discussed, and locations of principal mining districts, custom mills, and smelters are shown. Explanations of treatment processes, ore types, treatment charges, payments for metals, and deductions are given. Published rail and truck freight rates for mine products, based on marketing patterns developed over many years, are listed and explained.

Jan 1, 1964

This appendix contains the list of equipment, their corresponding number and their specifications with the quotations from the vendors/ manufacturers who can supply this equipment. The listings are arranged by process plant areas.

Jan 1, 1979

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941