Search Documents

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By Harry V. Makar

As part of a continuing research program for conserving domestic mineral resources, the Bureau of Mines is investigating new and improved scrap identification techniques to improve sorted mixed scrap purity. This report focuses on various classes of wrought and cast copper alloys produced with recycled scrap. Based on a survey of the literature, principal alloys, such as the brasses and bronzes, are examined with respect to impurity elements and their effects on metallurgical behavior. Effects of elements such as lead, antimony, iron, chromium, and aluminum are discussed. The metallurgical effects described include hot shortness, fire cracking, and undesirable phase transformations.

Jan 1, 1985

By W. W. Adams

"Accidents at coal mines in the United States in September 1926 resulted in the loss of 170 lives, according to information furnished to the Bureau of Mines, Department of Commerce, by State mine inspectors. Of this number 125 occurred at bituminous mines and 45 in the anthracite field. As the bituminous output of coal for September was 48,976,000 tons, and the production of anthracite was 8,444,000 tons, the fatalities reported represented a death rate of 2.55 per million tons for bituminous mines and 5.33 for anthracite mines. The industry as a whole showed a fatality rate of 2.6 per million tons of coal produced in September 1925 the rate for bituminous coal mines was 3.29; the anthracite mines were idle in September last year due to a strike.During the first nine months of the present year 1,759 men have been killed by accidents at the coal mines throughout the United States, resulting in a death rate, per million tons of coal produced, of 3.76 as compared with 3.95 for the same period in 1925. Reports for bituminous mines alone showed a nine-month fatality rate of 3.53 which was about the same as the corresponding rate from January to September in 1925. The anthracite rate for the present year, however, shows a decrease of about 17 per cent; that is, the rate has declined from 6.36 to 5.28.Records covering the first nine months of 1926 show that 12 ""major"" disasters, that is, disasters in which five or more men were killed at one time, have resulted in the loss of 271 lives as against 10 disasters and 199 deaths in the corresponding months in 1925. The fatality rates for these disaster: alone were 0.579 and 0.465, respectively. One major explosion occurred at Tahona, Oklahoma, on September 3, 1926, in which 16 men lost their lives.An analysis of the principal causes of the 1,759 fatalities for the first nine months of the present year shows a reduction in the death rate as a whole and for falls of roof and coal and for explosives, but an increase in haulage, gas and dust explosions, and electricity. The comparative rates for these accidents were:"

Oct 1, 1926

By David E. Siskind

The Bureau of Mines has studied the fracturing and associated damage occurring in the vicinity of blastholes from five shots fired in the shale pillars in the White Pine copper mine, White Pine, Mich. Four types of explosives (AN-FO, commercial extra dynamite, ammonia gelatin dynamite, and a low-density, low-velocity permissible) were used. Cores were taken from the blast region and examined by ultrasonic and petrographic techniques. Pulse wave velocities were measured across the core diameters, and thin sections showing cracks and changes in lithology were examined in an attempt to establish zones of damage. Cores from the blast regions and areas near pillar free faces were found to have abnormally low pulse velocities. Petrographic study of the thin sections showed that the negative velocity anomalies were caused by cracks in the cores. Crushing and extensive fracturing prevented meaningful measurements on core fragments from the immediate blast vicinities. Compositional, changes and other rock nonuniformities, such as joints and preexisting fractures, tended to mask detailed damage differences among the four explosives; however, the two most energetic explosives (extra dynamite and ammonia gelatin dynamite) produced damage zones two to three times as large as the AN-FO and low-velocity permissible explosives.

Jan 1, 1973

By K. F. Anderson

The increasing number of oil-productive reservoirs in the Ellenburger formation has emphasized the need for information pertaining to the hydrocarbon recoveries that may be obtained from such reservoirs. Most of the space available for accumulating hydrocarbons in the Ellenburger formation is derived from fractures, which makes it difficult to estimate reserves or probable recoveries. The Ellenburger reservoir in the Big Lake field was selected for study because it is one of the few near-depleted reservoirs in the area. The experience gained in operating and developing this reservoir has been and should continue to be a helpful guide to operators both in predicting recovery and establishing methods of development and operation In similar reservoirs. Development and production data were gathered from different sources. The writers have compiled and interpreted these data to estimate the ultimate recovery of hydrocarbons. In addition to the estimates of ultimate recovery, the report contains sample calculations and estimates of theoretical recovery based on different methods of operation. The calculations presented in this report indicate that the Ellenburger reservoir is 95 percent depleted and that the ultimate recovery of hydrocarbon liquid from the oil reservoir and gas cap combined will he 4-0 barrels per gross acre-foot of reservoir rock. An estimated 32 barrels of condensate per gross acre-foot of reservoir rock in the gas cap has been recovered, and the estimated ultimate recovery of crude oil will be 47 barrels per gross acre-.foot of rock in the crude-oil reservoir.

Jan 1, 1954

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

Although the Stamler feeder/breaker has been used for coal crushing in underground mines for many years, it has only recently been applied to other crushing operations. Two companies presently using Stamler feeder/breakers for rock crushing were contacted regarding their experiences with the units in actual field use. In both cases information was obtained directly from the individuals responsible for field operation and maintenance of the units. White Pine Copper Co. has been using Stamler feeder/breakers for over two years to crush copper ore. They now have fourteen 450-ton-per-hour units on line. The ore has a compressive strength of from 18,000 to 28,000 psi and is extremely abrasive. Maintenance is performed on a tonnage basis. The breaker shaft is replaced every 250,000 tons (requiring about 4 hrs) and picks are replaced about every 1500 tons by the operator (requiring about 2 min per pick). Very little unscheduled maintenance has been required. Crushing costs are fairly high (estimated at 13 to 15t per ton including maintenance and operation) because of tale extreme abrasiveness of the material. A new Stamler feeder/breaker with Ultramet wear surfaces was put or line in June 1976. Ultramet was found to increase the life of belt transfer station surfaces by up to 400 percent and it is hoped that it will do the same for the feeder/breaker. At this time it is still too early to evaluate the performance of the Ultramet unit. If it does improve abrasion resistance, crushing costs could be greatly reduced. White Pine is very pleased with the units and the service provided by Stamler.

Jan 1, 1976

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspar as a substitute for natural fluorspar flux in basic cupola ironmaking. The synthetic fluor-spars tested were prepared from waste fluosilicic acid generated during the processing of fluorapatite ore. The cupola trials showed the synthetic products to be the equivalent of natural fluorspar from an operational standpoint. However, wet scrubber sampling showed that substantial losses of volatilized fluorine occurred from the cupola during operation. The losses during synthetic fluorspar trials considerably exceeded those from natural fluorspar trials. Laboratory viscosity testing, using a high-temperature rotational viscometer, confirmed this finding and indicated that fluorspar volatility in slags is related to slag basicity. Synthetic fluorspar is accordingly recommended more for highly basic cupola operation (>1.3 basicity) than for neutral or acid operation, because of the increased potential for pollution and baghouse filter detezioration"

Jan 1, 1989

By G. A. Morrison

Iron ores associated with the Oriskany formation extend from the West Virginia border to the southwestern corner of Virginia. The deposits have been mined at many places, and the district is credited with the production of approximately 13,000,000 tons of ore to 1925, when mining operations ceased (fig. 1). The Oriskany iron-ore deposits occur in the Alleghany Mountains throughout their extent in the State. The name Oriskany was originally given to the limonite ore that was supposed to occur in the Oriskany sand-stone. At present, the name applies to all iron-ore deposits occurring in the lower part of the Devonian shale, Oriskany sandstone, and Helderberg limestone. The principal ore-bearing minerals are goethite and limonite. This report deals principally with the occurrences in Allegheny, Bath, Botetourt, and Craig Counties, Va. The Bureau of Mines, as part of the strategic-minerals program, began a project to develop the reserves of the area in November 1943; and continued until December 1944. Work started near Oriskany and extended northeast for nearly three-fourths of the area of the more important deposits. During the program 163 holes were drilled, totaling 11,651 feet; 256 feet of prospect tunnels were driven; 1,346 samples were collected; beneficiation tests were performed; and bulldozer trails and trenches wore excavated. The work served to delimit and appreciably extend the reserves of several areas. Analyses of channel samples are -given in appendix A, and diamond-drill and churn-drill hole logs and sample analyses are given in appendixes B and C, respectively.

Jan 1, 1950

By H. A. Dierks, H. B. Link

The purpose of this investigation was to develop a practical feeder apparatus to introduce comparatively large pieces of coal and similar material into a pipeline under pressure in connection with the vertical hydraulic transportation of solids , termed " hydraulic hoisting . " This method of hoisting the precrushed run - of - mine product of an underground mine has been given unusually wide attention abroad and could be of considerable significance to the U.S. mining industry in its search for operating improvements and cost reduction . A lock-hopper assembly was developed after a series of sinking velocity tests were made by dropping anthracite in a column of water . The system functioned reliably as an automatically operated feeder apparatus .

Jan 1, 1964

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990

By Marvin W. Wilson

The Federal Bureau of Mines has conducted laboratory experiments simulating underground gasification of coal to study the feasibility and mechanism of the process and determine the chemical and physical characteristics of a coal-bed during gasification. Laboratory and small-scale field experiments also were made to investigate the properties of coal and other factors affecting the electrolinking-carbonization method of preparing a path through a coalbed before gasification. Laboratory experiments simulating underground gasification of coal: Experiments with a laboratory retort indicated that bituminous-coal deposits could be gasified in place to produce a combustible gas.

Jan 1, 1960

This report describes a U.S. Bureau of Mines investigation into the removal of gate road chain pillars in conjunction with longwall retreat mining. The research objective was to determine, through evaluations of the loads imposed on the gate road pillars and supplemental support elements in the entries, how the pillars, supplemental support, and entries were affected by the longwall abutment pressure. To achieve this goal, vibrating wire stressmeters and hydraulic flat jack pressure cells were installed in the support elements to monitor stress change caused by abutment pressure as a function of longwall face advance. The findings documented in this report are the result of information collected from instrumentation and observation at the mine. Pillar and support loading measurements and stability observations revealed that the roof and the support elements remained stable during panel retreat, while the face progressed at a normal rate of advance. The ability to safely and efficiently mine chain pillars during panel retreat increases resource recovery and can provide several other benefits described in this report.

Jan 1, 2010

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By John C. Cook

A 1-year program of exploratory research, to determine the feasibility of radar exploration in advance of coal mining, has been completed. Advance detection of obstructions including faults, clay veins, abandoned wells, and pyritic concretions would improve the safety and efficiency of mining. Initial calculations based on laboratory tests of the RF electrical properties of bituminous coals indicated feasibility; radar waves at frequencies below 100 MHz should be detectable through tens to hundreds of meters of coal and be well-reflected by clay, pyrite and metal obstructions. Using a proprietary, experimental, VHF short-pulse "mining radar" system, two cycles of field testing and equipment improvement were completed. Measurements were made in three bituminous coal mines, a quarry, and a salt mine. Comparisons were made with ground-penetrating radar equipment developed by others for salt dome exploration and for military tunnel detection. The proprietary mining radar equipment and techniques used were found to be the most effective known for coal exploration, but further improvements are needed; one major problem in all systems is interfering clutter signals arising in the equipment and from mine room reverberations through leakage coupling of the antennas to the air. Nevertheless, several practical goals have been achieved: excellent radar reflections were received and identified through up to 30 feet of coal; reflections from a wet, abandoned drill hole were identified by their polarization property and detected at distances up to 272 feet, and mine-wall reflections were detected at distances up to 735 feet (both through salt); propagation through and reflections from large vertical clay veins in coal were demonstrated; experimental results agree reasonably well with theory. The results and experience gained during the project affirm the feasibility of the method. They also provide a firm basis for the development of a practical radar technology for exploration in advance of mining. No Subject Inventions, as defined in the contract, were made in the course of this work.

Jan 1, 1971

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By E. G. Baglin

The Bureau of Mines devised a procedure for selectively extracting platinum-group metals (PGM) and gold from Stillwater Complex flotation concentrate. The Stillwater Complex is the only major U.S. PGM resource. Development of a suitable extraction technique will contribute to its exploitation. The concentrate was roasted at 1,050° C to convert host base-metal sulfides to oxides and the PGM from sulfide minerals to their elemental states. The roasted concentrate was preleached with dilute sulfuric acid to remove easily soluble gangue minerals. After pre-leaching, the concentrate was slurried with 6M HCI and leached at ambient temperature and pressure with a strong-oxidizing agent. Hydrogen peroxide, chlorine, sodium hypochlorite, nitric acid, and a persulfate salt were the oxidants investigated. The two-stage leaching scheme ex-tracted up to 97 pct of the platinum, 92 pct of the palladium, and 99 pct of the gold from the roasted concentrate. The base metals were not solubilized and reported to the residue. No attempt was made to devise a procedure to recover the copper and nickel because they comprise less than 5 pct of the value of the concentrate. Viable techniques for recovering the precious metals from the pregnant solution were sulfide precipitation, cementation with nickel, or adsorption on activated carbon.

Jan 1, 1985

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995