Search Documents

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems in developing urban areas. Uncertain knowledge of abandoned coal mines also imposes potential hazards in coal excavation operations since water inundation or the release of methane gas is a pricnipal hazard when mine excavation operations break into an abandoned mine. U.S. Army requirements for an effective method for detecting and mapping subversive man-made tunnels have resulted in a surface-operated automatic earth resistivity survey system with a digital computer data processing system. Field tests aimed at demonstrating the system performance resulted in successful detection of tunnels having depth-to-diameter ratios up to 15 to 1. Under the sponsorship of the Bureau of Mines, a similar system was designed and constructed for use in the detection of coal mine workings. This report discusses the hardware and software aspects of the system and the application of the high-resolution earth resistivity method to the survey and mapping of abandoned coal mine workings. In the field tests reported, the targets of interest were both air-filled and water-filled workings.

Jan 1, 1980

By Alvin Kaufman

Increased exploration in Alaska has resulted in many requests to the Bureau of Mines for facts about the mineral resources and mining conditions in the Territory. This report presents information about the minerals of Southeastern Alaska and the factors that affect development of a mining industry in that area. Southeastern Alaska is a narrow coastal strip of rugged mountains and many islands. The climate is mild, with an average annual temperature of 40° and heavy rainfall. Geologically, the region is favorable for deposition of ore; geographic-ally, it is difficult to prospect and to develop, except along areas immediately adjacent to the coastline.

Jan 1, 1958

By C. M. Dice

This paper is one of a series being published by the Bureau of Mines on milling methods and costs. It describes briefly the procedure followed in concentrating hübnerite or? at the Ima tungsten mine, Lemhi County, Idaho. In October 1911 the Ima mill was utilizing combined gravity-concentration, flotation, and magnetic-separation units for the recovery of a tungsten concentrate and a pyritic silver concentrate approximately 120 tons of ore averaging 0.5 percent W03 is treated daily. The concentrates produced average 66 to 67 percent WO3.

Jan 1, 1943

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

By James P. Bennett

To identify construction materials for emerging technology in chemical and metallurgical processes, the Bureau of Mines investigated the acid resistance of ceramic materials. Eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a five-claybonded silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed for 110 days to 20 wt pct HCl at 50°, 70°, and 90° C and to 30 wt pct HCl at 70° C. Statistically significant changes in cold crushing strength, volume, and weight were generally small or not detected. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. The carbon brick sample had the best acid resistant properties with a maximum total leached ion weight loss of 0.004 wt pct. The silicon carbide, the silica, and one of the fire clay bricks also had excellent acid-resistant properties.

Jan 1, 1983

By Frank E. Cash

The data in this circular were compiled so that individual phosphate companies might have the benefit of the experience of other phosphate companies, and that industries in general might compare experiences (taking into consideration relative hazards), thereby promoting accident preven¬tion. ACKNOWLEDGMENTS The descriptive matter is taken in part from a. paper by Cash and von Bernewitz.4/ Production figures ore from Mineral Resources of the United States;5/ accident data were furnished by each of the operating companies in the pebble-phosphate district, and their assistance in making this report possible is gratefully acknowledged.

Jan 1, 1936

By J. E. Miller

Primary standard gas mixtures were developed for more accurate calibration of analytical instruments at the Bureau of Mines Helium Research Center and for calibration of analytical instruments used in the helium conservation program. A 10-kg-capacity balance is used to weigh a 4-kg metal cylinder filled to high pressure (1,800 psi maximum) with the component gases of the desired mixture. At 1,800 psi, a cylinder contains about 60 g of helium, or 420 g of nitrogen. An accuracy of ±0.05 mole-percent or better is claimed for each component in the mixtures.

Jan 1, 1965

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By P. W. Jeran

The Stereonet Analysis Program (SNAP) is a mathematics tool which, by means of a computer, reproduces mathematically the manual techniques of pre- paring stereograms. This computer program was developed to provide a fast, accurate, and economical means of analyzing fracture orientation data. It is mitten in FORTRAN IV for use on a UNIVAC 1108 operating under an Exec II system, but can be adapted to other systems. SNAP is currently being used to aid in the analysis of cleats and other geologically induced fractures associated with coalbeds that are being mined underground, Methane flows through the coalbed and into these mine workings predominantly through the fracture system. Therefore, knowledge of fracture orientation is an invaluable aid in the development of methane control technology.

Jan 1, 1970

By Oliver Bowles

The exingencies of a world war have brought home to the American public, especially the people of the. Eastern States, the urgent need for conserving fuel. Transportation problems in the East have created an unprecedented situation wherein fuel-oil supplies are greatly restricted, and the consequent increase in demand for coal further complicates the problem of transporting and storing that commodity. People should awaken to the need for utilizing every possibly means of conserving to fuel, even to the extent of reducing the temperature in their homes.

Jan 1, 1942

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By M. M. Tilman

As part of ongoing research to improve mine safety, the Bureau of Mines conducted research on the corrosion of friction rock stabilizer steels in five Missouri lead and iron mine waters. Electrochemical corrosion tests, including evaluation of pitting tendency, were performed on two types of high-strength, low-alloy (HSLA) steels and galvanized steel in four Missouri lead mine waters and one Missouri iron mine water. The tests were conducted at in-mine water temperatures in both air-saturated and deaerated waters. Static, weight-loss corrosion tests were also conducted on HSLA steel specimens in the five Missouri mine waters for 2,900-h duration at average in-mine water temperatures and air-dissolved oxygen contents of 6 to 7 ppm. Corrosion rates determined by the weight-loss tests were roughly comparable with rates determined electrochemically in deaerated waters containing 0.3 to 0.5 ppm dissolved oxygen content. Passivation of specimen (nongalvanized) surfaces in air-saturated waters resulted in very low electrochemically deter- mined corrosion rates. Pitting-tendency was generally higher for both HSLA steels in air-saturated waters than in deaerated waters. Galvanized steel generally exhibited higher tendency to pitting in the deaerated waters than in the aerated mine waters.

Jan 1, 1985

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By John W. Buch

This is the first progress report to be released on the anthracite, mechanical mining research and engineering development program of the Bureau of Mines. This phase of Bureau work, which was initiated as an aid to stimulating wartime production of anthracite, has been continued after the war to assist primarily in improving the general economic position of the anthracite industry. Field work was started in. the 1945 fiscal year with the cooperation of an advisory committee representing management, labor, and the Commonwealth of Pennsylvania. For a beginning, several matters were suggested by members of this advisory committee as being worthy of investigation, and sections of underground mines yore offered for test purposes. Among the suggestions accepted for investigation was the problem of increasing the rate of advance for driving gangways in thin, steeply pitching anthracite beds 4 to 6 feet thick and pitching 60 degrees or more. The problem was undertaken as a field study, and this report relates to accomplishments on this project to June 30, 1947.

Jan 1, 1949

By A. C. Richardson

[During the past two and a half sears the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators, have been making an extensive studs of coal preparation in the State of Alabama. Considerable time has been devoted to the studs of the washing characteristics of the Mars Lee bed and the various methods used In preparing from it a low-ash coal suitable for the manufacture of metallurgical coke. One of the phases of this problem is the utilization of middlings products from the washing plants. This paper gives the results of treating jig middlings on a coal-washing table at the Bureau of Mines laboratory at Tuscaloosa, Ala. The sample used was secured from the Sayreton washery of the Republic Steel Corporation, Sayreton, Ala. WASHERY PRACTICE The Mary Lee bed is very bony, and operators find it difficult to produce from this bed a washed coal much under 10 per cent ash. Experience has shown that in the preparation of a coking coal from the Mary Lee bed it is best to use a process which permits the recovery of a middlings product. Middlings are desirable because separation according to specific gravity is never perfect, and a middlings product makes possible a low ash in the primary warned coal without excessive losses of combustible in the refuse. The general washery practice on the Mary Lee bed is to crush the run-of-mine coal through some maximum screen size and wash it upon some one type of jig without re-treatment of any of the products made. The maximum size treated varies from 3 inch to J inch. The middlings product from multiple-cell jigs is usually termed "boiler fuel" and when possible is utilized as such. At present the production of boiler fuel is often in excess of power requirements, and the surplus, due to its high ash content, becomes waste.]

Jan 1, 1931

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By Irving Hartmann, John Nagy, Donald Mitchell

"SUMMARY AND CONCLUSIONThe test data indicate that water infusion of the Pittsburgh coal seam does not reduce the amount of fine dust produced during mining operations to the extent reported elsewhere. Wide variations in the amounts of dust collected in the air current were noted in duplicate samples and repetitive tests. Changes in depth and location of the infusion holes and amount of water injected and addition of a wetting agent to the water had little effect on the amount of dust liberated.Water was forced readily into the coal. Some water flowed out along the cleats, but an appreciable amount remained in the seam. Little or no water pene¬trated the coal seam above the upper infusion holes.The average dust concentration (with and without infusion) in the return air, 40 feet outby the working face, was 25 million particles per cubic foot during undercutting, 20 million during drilling, 75 million during shot firing, and 20 million during hand loading. At the working face the average concentration was 3 to 6 times higher. The concentrations were measured at an airflow of 1,600 cubic feet per minute (c.f.m.) at the face.On the basis of this short investigation, no final conclusions can be made on the effectiveness of water infusion in reducing the amount of fine dust liberated during mining in the Pittsburgh coal seam. However, the data indicate that dust reduction resulting from infusion would be small.INTRODUCTIONThe production of fine coal dust is an inherent part of nearly every phase of mining. The use of large, high-speed continuous-mining machines and other mechanical equipment has increased dust production. In addition, in coal seams that have been subjected to high pressures for a long period, and particularly in dry and friable seams, some very fine dust is in the seam before mining. Much effort has been devoted to allaying and collecting at its source the fine coal dust released during mining. One of the comparatively recent techniques that has been developed for this purpose is infusion of water or other liquids into the coal seam. This method consists of injecting water under pressure into a coal seam to neutralize the fine dust released during mining. The water generally is introduced through bore holes in the face before undercutting."

Jul 1, 1957

By Irving Hartmann

The Experimental Coal Mine of the Bureau of Mines has served principally as a valuable and unique testing laboratory for studies of the explosibility of coal dust and mine gas; studies of the numerous complex and interrelated chemical and physical factors that govern the ignition of coal dust and the propagation of mine explosions; and studies designed to develop measures for preventing explosions or reducing their destructive effects. These researches, coupled with educational efforts by the Bureau of Mines and enlightened safety consciousness in the mining industry, had fruitful results. This is evidenced by the remarkable reduction in the frequency of major coal-mine explosions and the number of fatalities from explosions since the Bureau of Mines was established. Despite this progress, further important unresolved problems arise; these are due in part to changes in mining conditions and methods, which have brought about increased production of fine coal dust in highly mechanized operations. To solve the new problems, research must be continued without interruption. The results of many very recent and current studies in the Experimental Coal Mine are summarized briefly, and pertinent studies by European mine-safety-research organizations are listed.

Jan 1, 1957

By E. Robert Ruhlman

["Phosphate rock" is a broad term applied to natural deposits of minerals valued chiefly for their phosphorus content. More specifically, phosphate rock may be defined as a natural rock containing one or more phosphate minerals, usually calcium phosphate, of sufficient purity and in sufficient quantity to permit its use directly, or after beneficiation, in the manufacture of phosphorus-bearing products. The grade or quality of phosphate rock is expressed either in terms of its phosphorus oxide (P20S) content or the equivalent in tricalcium phosphate (Ca3(P04)2). The trade name for tricalcium phosphate is bone phosphate of lime (B. P. L.).]

Jan 1, 1958